MINOURA RS-1100 User manual

- Page : 1 -
Seat Tube Stay
Front Tire Stopper
Knob Bolt - B
Upper Frame
Knob Bolt - A
BB Support Lock Button
BB Support Bracket
Knob Bolt - C
Leg - B
Leg - A
Lock Release Button
Lower Frame
Down Tube Supporter
Seat Tube Support Bracket
Arm
RS-1100 Bike Fellow 2 Repair Stand
INSTRUCTION MANUAL
Thank you for purchasing the Minoura RS-1100 repair stand.
This foldable, light weight multi purpose stand allows you to use it as both a repair stand
and a display stand.
A convenient Carrying Bag with a tool pocket is available as an option.
IMPORTANT NOTES:
RESOLUTION DIAGRAM

-Page : 2 -
HOW TO ASSEMBLE
¶ No tools are required to assemble your RS-1100.
Loosen Knob Bolt-A on Lower Frame, slide up
Upper Frame, and tighten again Knob Bolt-A
slightly (see Fig. 1) .
Open Leg-A fully until the leg locks (clicks) in
place. When you hear the click sound, Leg-A is
locked automatically.
After that, open Leg-B fully, then place this
stand on the floor (see Fig. 2) .
!
!
!
!
(Fig. 1)
(Fig. 2)
(Fig. 3)
(Fig. 4)

- Page : 3 -
Turn both Arm and Seat Tube Stay fully.
Insert Seat Tube Support Bracket through and
into the Seat Tube Stay, and insert the plastic
cap.
(see Fig. 5)
The BB Support Bracket will help your
bike stable during on this stand.
The BB Support Bracket will open auto-
matically when you open Arm.
(see Fig. 6)
When you wish to fold the legs, you must keep
pressing each Lock Release Button on the Leg-
B, then fold the Leg-A.
(see Fig. 8)
If you don’t wish to use BB Support Bracket or
if you wish to fold this stand, push the Lock
Button on the bottom of the Arm. The BB
Support Bracket may then folded up or down.
(see Fig. 7)
(Fig. 5)
(Fig. 6)
(Fig. 7)
(Fig. 8)

-Page : 4 -
USE RS-1100 AS A REPAIR STAND
Place RS-1100 on a flat stable surface.
Pull up the Arm Stopper and insert it into the
angled hollow firmly to lock it (see Fig. 9) .
Arm Stopper
To begin set the left side crank arm
downward or a little forward, then
twist your bike about 20 degrees
counter-clockwise and lift it up.
(see Fig. 10)
!
Place the down tube onto both Down Tube
Supporters gently.
(see Fig. 12)
!
!
(Fig. 9)
(Fig. 10)
(Fig. 11)
(Fig. 12)

- Page : 5 -
Then support the seat tube with Seat Tube
Support Bracket.
Adjust the position of the bracket not to pinch
the cable. The bike is supported safely .
(see Fig. 13)
Adjust the angle of Arm with Knob Bolt-B in
order to fit all contact points to the bike. Make
sure all contact points are supporting the bike
properly.
(see Fig. 14)
USE RS-1100 AS A DISPLAY STAND
Finally, sandwich the front wheel with both
Front Tire Supporters.
This device will make your bike stable and help
your work securely while the bike is on this
stand.
(see Fig. 14)
Place the RS-1100 on a flat and horizontal
floor.
Pull the Arm Stopper out fron the slot and lay it
down. (see Fig. 15)
Push the Lock Button of the Arm and fold down
the BB Support Bracket.
Then turn the Arm horizontally.
(see Fig. 16)
¶ RS-1100 also can be used as a display stand or temporary bike stand.
!
(Fig. 13)
(Fig. 14)
(Fig. 15)
(Fig. 16)

-Page : 6 -
Place the top tube down softly on
both Down Tube Supporter. (see Fig.
17)
!
FOR WARRANTY, MORE INFORMATION
CONTACT :
MINOURA JAPAN
1197-1 Godo, Anpachi
Gifu 503-2305 JAPAN
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
URL: http:// www.minoura.co.jp
(Fig. 17)
MINOURA WARRANTY CENTER
1415 San Mateo Avenue,
South San Francisco, CA 94080 U.S.A.
Toll Free: 800-601-9592
MINOURA NORTH AMERICA
37653 B Argyle Rd.
Fremont, CA 94536 U.S.A.
Phone: [phone]
Fax: [phone]
E-mail: [email protected]