MINOURA P-600AL User manual

Type-A: plain type bolt
Type-B: with Spring Washer
1
2
3
5
P-600AL "Closet Cyclist 2" instructions manual
Upper Hook
Main Pillar
Lower Hook
Reinforcement Bar
Rear Leg
Right Side Front Leg
Height Adjuster
Leg Base Plate
Stainless Band Clip
• For use of normal human-powered 2-wheel bicycles only. Heavy and long bikes
such as tandem, electric assisted and downhill / freeride bikes don't t P-600AL.
• P-600AL may lose balance when hanging bike on just one side only depends on
the bike weight. Be careful about the stability when taking off the bike.
• You should setup P-600AL along a wall to prevent falling backward problem. Do
not install the bike on the backside of P-600AL.
Required Tools for Assembling
Bolt Type Recognition
Install both right and left Front Legs to the
Leg Base Plate with the supplied M6x35
bolt (type-A), Flat washer, Collar and M6
Nylon nut. (see Fig. A)
M6 Nylon Nut
Collar
M6 Flat
Washer
Left Side
Front Leg
Place the Rear Leg on the Leg Base
Plate, and put the Pillar Base Plate
onto the assembled legs.
Put the M6x40 bolt (type-A) with
M6 Flat Washer into the front side
hole, then tighten to M6 Nylon Nut
temporarily. (see Fig. B)
Pillar Base
Plate
M6x40 Bolt (type-A)
Rear Leg
Put the M6x40 bolt (type-A)
with M6 Flat washer into the
backside hole and tighten to M6
Nylon Nut rmly.
After that, tighten the front side
bolt rmly too. (see Fig. C)
M6x40 Bolt
(type-A)
Attach the Backside Leg on the back
of the Main Pillar, then tighten with
the supplied two M6x18 bolts (type-B)
temporarily.
Please note that you will tighten
these bolts rmly after installing the
Reinforcement Bars. (see Fig. E) Backside Leg
M6x18 Bolt
Main Pillar
1 x M5 Hex Wrench
1 x 10mm Spanner
1 x 13mm Spanner
M6x35 Bolt (type-A)
Leg Base Plate
MADE IN JAPAN
IMPORTANT NOTICES
Be sure the Legs are different
for right side and left side.
Each Reinforcement Bar must
be located inward.
!
M6 Nylon Nut
!
Be sure the collar insertion
direction is different on right
and left side. Follow as
shown in Fig. A.
(Fig. A)
(Fig. B)
(Fig. C)
(Fig. D)
(Fig. E)
M6 Nylon Nut
4Insert the Main Pillar onto the Pillar
Base Plate.
Make sure the Main Pillar must cover
on the bracket, not placing beside the
bracket. (see Fig. D)
M6 Flat
Washer
M6 Flat
Washer
Stainless Band Clip
(2009/07)

6
7
8
!
!
!
M6x70 Bolt
(type-A)
Raise up the Reinforcement Bars and attach to the Main Pillar with the
supplied M6x70 bolt (type-A), Plastic Shim, M6 at washer and M6
Nylon nut.
After installing the Reinforcement Bars, adjust the Backside Leg height
to touch the oor all together, then tighten the M6x18 bolts on the
Backside Leg rmly. (see Fig. F)
Plastic Shim
Reinforcement Bar
Install Upper Hook (Fig. G) and Lower Hook (Fig. H) to the Main Pillar.
Each bike requires both hooks and they are fully position adjustable.
Find out the best position to hang down your bike most efciently.
To install the Stainless Band Clip, follow the steps below;
1) Once disassemble the Stainless Band Clip.
2) Open the band and wind it around the Main Pillar.
3) Lap the band ends (see Fig. I). The end with a welded nut must be
inward. Make sure that both ends t each other. If not, adjust the
bending angle.
4) Attach the Plastic Bracket onto the band. It should be snapped in.
Upper Hook Lower Hook
P-600AL is a tall stand. You must maintain the balance
whenever you use it to prevent from any accident.
Adjust the Height Adjuster on each legs to keep the
Main Pillar truly vertical and stable, then tighten the
Lock Nut rmly with a 13mm spanner. (see Fig. K)
< Complete Style with Bikes >
For More Information
MINOURA JAPAN MINOURA NORTH AMERICA
(for ALL customers) (for U.S. residents ONLY)
1197-1 Godo, Anpachi 1996 East Avenue
Gifu 503-2305 Japan Hayward, CA 94541-5454 U.S.A.
Phone [phone] Phone [phone]
Fax [phone] Fax [phone]
Email [e-mail] Email [email protected]
Web www.minoura.jp
Washer
Washer
Nylon Nut
(Fig. F)
If you have any questions or need help, you should contact the dealer where you purchased
or the Minoura distributor in your country rst. The distributor can be found on our web site.
Only when you cannot get enough service, you can contact us.
(Fig. K)
Please attach the Lower Hook
from the back of the rear wheel
to support it, otherwise the
bike will not become vertical
to save the space due to the
bike's weight balance.
If the inside band end with welded nut has
been angled against the bolt, you won't be
able to screw the bolt in.
Make sure the nut side end is properly set
at right angle to the bolt. (see Fig. J)
Do not push the bolt so much when
screwing in. The band end will have to
be bent and you are no longer tighten
the bolt.
5) Put the bolt into the hole on the hook, then screw into the bracket gently.
6) Adjust the hook position and tighten the bolt rmly.
Lock Nut
Height Adjuster
(Fig. G) (Fig. H)
(Fig. I)
(Fig. J)
90º
Stainless Band (45mm)
Plastic Bracket
M6 Flat Washer
M6x30 Bolt (type-A)