Minuteman Powerboss P260TDQP Guide

OPERATION ■SERVICE ■PARTS ■CARE
ES260
Floor Scrubber
Traction Driven
Brush Driven
Model #:
P260TDQP, P260TDCE,
P260TDQPIW,
P260BDQP, P260BDCE

TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS...........................................................................................................................................1
FOR SAFETY DURING OPERATION: ..............................................................................................................................................1
FOR SAFETY WHEN SERVICING OR MAINTAINING MACHINE:..............................................................................................1
ELECTRICAL REQUIREMENTS .......................................................................................................................................................2
BATTERY REQUIREMENTS.............................................................................................................................................................2
BATTERY SERVICE AND INSTALLATION....................................................................................................................................2
BATTERY INSTALLATION...............................................................................................................................................................2
CHARGING BATTERIES ...................................................................................................................................................................2
CONTROL PANEL IDENTIFICATION..............................................................................................................................................3
OPERATING INSTRUCTIONS............................................................................................................................................................4
MAINTENANCE.....................................................................................................................................................................................4
REAR SQUEEGEE.................................................................................................................................................................................5
REAR SQUEEGEE COMPONENTS...................................................................................................................................................5
REAR SQUEEGEE ADJUSTMENT....................................................................................................................................................6
EXPLODED VIEWS...............................................................................................................................................................................7
MAIN ASSEMBLY..............................................................................................................................................................................7
MAIN ASSEMBLY BOM....................................................................................................................................................................8
SOLUTION &RECOVERY TANK (BRUSH DRIVE).......................................................................................................................9
SOLUTION &RECOVERY TANK BOM (BRUSH DRIVE) ...........................................................................................................10
MAINFRAME ASSEMBLY (BRUSH DRIVE).................................................................................................................................11
MAINFRAME ASSEMBLY BOM (BRUSH DRIVE).......................................................................................................................12
LINKAGE ASSEMBLY (BRUSH DRIVE) .......................................................................................................................................13
LINKAGE ASSEMBLY BOM (BRUSH DRIVE) .............................................................................................................................14
CONTROL PANELS (BRUSH DRIVE) ............................................................................................................................................15
CONTROL PANELS BOM (BRUSH DRIVE)...................................................................................................................................16
SOLUTION &RECOVERY TANK (TRACTION DRIVE) ..............................................................................................................17
SOLUTION &RECOVERY TANK BOM (TRACTION DRIVE).....................................................................................................18
MAINFRAME ASSEMBLY (TRACTION DRIVE)..........................................................................................................................19
MAINFRAME ASSEMBLY BOM (TRACTION DRIVE)................................................................................................................20
LINKAGE ASSEMBLY (TRACTION DRIVE) ................................................................................................................................21
LINKAGE ASSEMBLY BOM (TRACTION DRIVE).......................................................................................................................22
CONTROL PANELS (TRACTION DRIVE)......................................................................................................................................23
CONTROL PANELS BOM (TRACTION DRIVE)............................................................................................................................24
SQUEEGEE LIFT MECHANISM ASSEMBLY................................................................................................................................25
SQUEEGEE LIFT MECHANISM ASSEMBLY BOM......................................................................................................................26
SQUEEGEE ADJUSTMENT MECHANISM ASSEMBLY..............................................................................................................27
SQUEEGEE BLADE ASSEMBLY....................................................................................................................................................28
WIRING DIAGRAM (TRACTION DRIVE)......................................................................................................................................29
WIRING DIAGRAM (TRACTION DRIVE CE)...............................................................................................................................31
WIRING DIAGRAM (BRUSH DRIVE) .............................................................................................................................................33
WIRING DIARGRAM (CE).................................................................................................................................................................35
MINUTEMAN INTERNATIONAL MADE SIMPLE COMMERCIAL LIMITED WARRANTY..............................................37

1
IMPORTANT SAFETY INSTRUCTIONS
Operators must read and understand this manual before operating or maintaining this machine.
Do not operate this machine in areas containing flammable or explosive materials.
This machine is designed solely for scrubbing dirt and dust in an indoor environment. Minuteman does not
recommend the use of this machine in any other capacity.
The information provided in this manual will help prevent a potential hazard to the operator and
equipment. Read this manual carefully and be aware when hazardous conditions can exist. Take necessary
steps to locate all safety devices on the machine and train the personnel operating the machine. Report any
machine damage or faulty operation immediately.
Do not use machine if it is not in proper operating condition.
FOR SAFETY DURING OPERATION:
Keep hands and feet clear of moving parts while machine is in operation.
Make sure all safety devices are in place and operate properly. All covers, doors and latches must be
closed and fastened before use.
During operation, attention should be paid to other persons in the work area.
Electric motors and components can cause an explosion when operated near explosive materials or vapor.
Do not operate this machine near flammable materials such as solvents, thinners, fuels, grain dust, etc.
Store or park this machine on a level surface only, with the key switch in the off position. To prevent
unauthorized use, machine should be stored with the key removed.
This machine is designed for level operation only. Do not operate on ramps or inclines.
This machine is not suitable for picking up hazardous dusts.
Use caution when moving this machine into areas that are below freezing temperatures. Any water in the
tanks or hoses can cause damage to the machine.
FOR SAFETY WHEN SERVICING OR MAINTAINING MACHINE:
Stop on a level surface and turn off the machine.
Disconnect the power to the machine by unplugging the large, red terminal below the recovery tank when
charging batteries or during installation or removal of brushes.
Avoid moving parts. Do not wear loose jackets, shirts, or sleeves when working on machine.
Avoid contact with battery acid. Battery acid can cause burns. When working on or around batteries, wear
protective clothing and safety glasses. Remove metal jewelry. Do not lay tools or metal objects on top of
batteries.
Charging batteries generates explosive gasses. Do not charge batteries when open flames or sparks are
present. Do not smoke. Make sure the charger is turned off before disconnecting it from the machine.
Charge the batteries in a well-ventilated area with the battery cover removed completely.
Do not clean machine with a pressure washer.
Authorized personnel must perform repairs and maintenance. Use ONLY Minuteman supplied
replacement parts.
SAVE THESE INSTRUCTIONS

2
ELECTRICAL REQUIREMENTS:
This piece of equipment operates on 24 VOLT DC.
BATTERY REQUIREMENTS:
4 x 6V, 275Ah batteries (Part Number 956740)
BATTERY SERVICE AND INSTALLATION:
WARNING: Battery acid can cause burns. When working on or around batteries, wear protective clothing
and safety glasses. Remove metal jewelry. Do not lay tools or metal objects on top of batteries.
BATTERY INSTALLATION:
1. Disconnect tank drain hose from rear of machine.
2. Raise the tank assembly by raising rear cover and tilting tank, Figure 1.
3. Install batteries as shown in Figure 2.
CHARGING BATTERIES:
Charging of batteries generates explosive gases. DO NOT CHARGE BATTERIES WHEN OPEN FLAMES
OR SPARKS ARE PRESENT. DO NOT SMOKE. Make sure charger is turned off before disconnecting it
from the batteries. Charge the batteries in well-ventilated area. Fluid levels should be checked before and
after charging and maintained at the proper levels.

3
CONTROL PANEL IDENTIFICATION

4
OPERATING INSTRUCTIONS
1. Filling: Fill the solution tank with the desired amount of water and add liquid cleaning solution
to the proper dilution ratio. DO NOT USE powdered cleaning chemicals. Powders are unlikely
to dissolve thoroughly, resulting in clogging the in-line solution filter. This can reduce or stop
water flow to the brush.
2. Close lid.
3. Turn on main power key switch (refer to page 5, #15).
4. Adjust main speed control knob (#14) to full counter-clockwise position. (Traction Drive Only)
5. Lower brush assembly:
•Depress foot pedal (#6) slightly and push in on lever (#4) to release. To increase brush
pressure, pull up and back on lever (#4) to lock position.
•To lift the brush, press the pedal down until lift mechanism engages.
•Brushes will begin to rotate when forward (#16) or reverse (#8) levers are engaged.
6. Adjust solution control feed lever (#3).
7. Lower squeegee assembly with lever (#2). This will turn on the vacuum motor. The vacuum will
remain on until the squeegee lever (#2) is raised. After this, the motor will continue to run for
an additional 10 seconds to clear the recovery lines.
Turning off the power using the key switch will immediately shut down all systems,
including vacuum motor, transaxle, and solution feed.
8. Squeeze forward handle (#16), and adjust forward speed using control knob (#14). (Traction
Drive Only)
After Use:
1. Raise brushes with foot pedal (#6), brushes and solution flow will turn off .
2. Raise squeegee assembly; vacuum will shut off 10 seconds after raising.
3. Solution and recovery tanks should be emptied after every use. These tanks can be
emptied using drain hoses (#5 & #19).
MAINTENANCE
Daily:
1. Clean float assembly & squeegee blades.
2. Recharge batteries (check battery acid levels before and after charging).
Monthly:
1. Check wear on squeegee blades.
2. Grease front and rear wheels.
3. Grease pivot points on the brush motor assembly.
Every 500 hours check the condition of carbon brushes on vacuum motor and brush drive motor.

5
L A
REAR SQUEEGEE
The rear squeegee is the main element that acts as the conduit that transfers the spent
solution into the recovery tank. A daily maintenance check of this component is essential to
have optimum machine performance. The rear squeegee assembly is equipped with a
universal front blade that allows the operator the option to use a slotted and a non-slotted side
for specific applications. Each blade configuration has two usable edges. The rear blade
however has four usable edges.
The squeegee is pre-adjusted at the factory. Adjustments may be required to get
optimum performance for different floors and conditions.
REAR SQUEEGEE COMPONENTS
A
B
C
D
E
F
G
H
Rear Squeegee Blade
Wing Nut (2)
Caster Stem (2)
Swivel Caster (2)
Wing Jam Nut (2)
Turnbuckle Adjustment Knob
Front Squeegee Blade
Wing Bolt (2)
I
J
K
L
M
N
O
P
Toggle Clamp
Front Strap (Long)
Front Strap (Short)
Rear Strap (Latch Side)
Rear Strap (Catch Side)
Latch
Guide Wheel (2)
Recovery Hose Intake
O
B
NM
C
D
E
F
J
H P
G I K

6
REAR SQUEEGEE ADJUSTMENT
1. Ensure that the scrubber is on a relatively flat surface. Turn on the key switch and lower the
squeegee to the floor using the squeegee lift lever. This turns the vacuum motor on.
2. Move the scrubber one or two feet forward slowly while someone behind the machine checks
the rear squeegee blade (item A) for uniform deflection to the floor.
3. If uneven deflection or lay is evident, minor adjustments may be necessary to avoid streaking
and uneven wear on the blade.
4. To correct this, loosen the wing jam nut (item B) in order to adjust the caster height. If the
squeegee blade is deflecting too much, the casters (item D) need to be lowered to control the
down pressure. Lower the caster by turning the exposed threaded stem (item C) on the
caster clockwise. Make the adjustment a few turns at a time. Repeat step 2.
5. If the blades are not deflecting enough, raise the caster by turning the stem counter-
clockwise to adjust the caster height to allow more down pressure on the squeegee. Repeat
step 2.
6. Make sure there is even deflection on the entire length of the rear blade. Adjust the casters
and retighten the wing jam nuts to lock the caster setting in place.
7. Pitch adjustment is necessary if the outer ends on the squeegee blade do not contact the
floor and there is too much deflection in the middle area or if the outer ends are over
deflected and there is no contact in the middle.
8. To adjust the pitch, Repeat step 2.
9. Loosen the two wing jam nuts (item E) that lock the pitch angle. Turning the knob (item F)
clockwise or counter-clockwise controls the forward and backward pitch of the squeegee.
Having the rear blades deflected uniformly along its entire length is the desired set-up.
10. Repeat step 2 until desired set-up is achieved.
11. In certain applications where a non-slotted front wiper blade (item G) is needed, detach the
rear squeegee assembly by loosening the two wing bolts (item H). Unlock the toggle clamp
(item I) on the front squeegee to release the front long strap (item J) and slide the front short
strap (item K). Flip the blade over to the non-slotted side. Reattach the straps and lock the
clamp back in place.
12. You can also easily replace the rear blade by unlatching the latch (item N) and removing the
two rear straps (items L& M) by sliding them off the assembly. You can then flip the blade
over in order to use a new edge for better wiping action.

EXPLODED VIEWS
MAIN ASSEMBLY
7

ITEM PART NO. REQ'D DESCRIPTION
1 260087 2 HINGE-15"
2 260090 1 REAR BASE CHAR GREY
2A 260256 1 BASE 260TD CHAR GREY
3 260091B 1 RECOVERY TANK, ES260320 BURGUNDY
4 260092B 1 SOLUTION TANK, ES260320 BURGUNDY
5 260093 1 CHASSIS MMAN 260
5A 260360 1 MAINFRAME MMAN 260 TD
6 260096B 1 LID RECOVERY 260 BURGUND
7 260098 1 FRNT SKIRT 260 BLACK
8 260142 1 SKIRT RETAINER, L SIDE
9 260143 1 SKIRT RETAINER R SIDE
10 260145 1 SPLASH SKIRT
11 260149 1 U CHANNEL 12"
12 260157 2 LID GSKT SHORT 260B
13 260158 2 LID GSKT 260B
14 260159 1 HOSE-VAC 1.5 X 78" WIRELOC
15 260160 1 RECOVER HOSE ASY260B
16 260169 1 LID FLAP
17 260170 2 RETAINER STRIP
18 260203 2 CLAMP-HOSE 102120 MURRAY
19 260212 1 SCREEN FILTER
20 260241 2 PIN-HITCH 7/16 X 3
21 260294 1 GASKET 260
22 260299 1 SHUT OFF PLATE ASY
23 260301 1 DEFLECTOR FLAP
24 260336 1 SKIRT RETAINER - FRONT
25 260664 2 REC LID MOUNT WMT, ES260320
26 450037 1 ADAPTER MCH
27 450081 1 WSR 1.908 X 2.41 X .03 SS
28 711106 20 SCR-ST-A 10 X .75 PL
29 712822 4 SCR-MC 10-24 X .50 SS
30 711161 10 SCR-HI/LO #10 X 3/4 ZINC
31 711505 4 WSR-FLT 1/4
32 711508 2 WSR-FLT .44 X 1.00 X .08
33 260022 1 .125R 1S1B SKIRT MOUNT BRACKET
34 712540 14 SCR-MC 10-24 X .37 SS TH
35 712565 17 SCR-MC 1/4-20 X .62 SS
36 712667 4 NUT-HEX NYLOC 1/4-20 SS
37 715607 1 DECAL-BATTERY CABLE ROUT
38 760263 2 FOAM TAPE 1/16 X 1/2
39 828970 1 WSR NEOP 1.87X2.4X.125
40 828971 1 NUT 1 1/2 PIPE THREAD
41 260024 2 WELD-BRKT SKIRT
42 715841 1 DECAL, ES260320
PARTS LIST
MAIN ASSEMBLY BOM
8

SOLUTION AND RECOVERY TANK (BRUSH DRIVE)
9

ITEM PART NO. REQ'D DESCRIPTION
1 130118 1 STRAINER-SOLUTION M3-40
2 210045 1 CABLE-SOLUTION CONTROL
3 210370 1 SOLUTION VALVE BRACKET
4 210408 1 FITTING BRASS TEE 3/8MPT&FPT
5 210409 1 FITTING BRASS 3/8MPT 3/8FPT
6 210410 1 FITTING BRASS 3/8FPT 3/8HOSE
7 210414 1 O RING 2-113
8 260029B 1 LID SOLUTION BURGUNDY
9 260091B 1 RECOVERY TANK 260 BURGUNDY
10 260092B 1 SOLUTION TANK 260 BURGUNDY
11 260156 1 FLOAT ASSEMBLY
12 260670 1 TUBING, PLASTIC 3/8 ID X 70"
13 260178 3 FITTING NYLON T 3/8HOSE
14 260179 4 HOSE-NYLOBRAID 3/8 X 2.38
15 260182 1 SOLUTION HOSE C/L 18"
16 260184 1 SUPPORT ANGLE
17 260202 1 HOSE ASY 260B NEW STYLE
18 260203 1 CLAMP-HOSE 102120 MURRAY
19 260214 2 TANK CABLE ASY 260
20 320269 1 STRAP, DRAIN PLUG RETAINING
21 342430 1 FITTING BRASS 3/8MPT 3/8HOSE
22 430114 1 FITTING NYLON CAP 1/4FPT
23 450021 1 HINGE
24 450040 2 ELBOW PLT 3/8MPTX3/8BARB
25 450055 1 HOSE NYLO 3/8ID X 9"
26 450076 12 CLAMP-CRIMP 185R SS
27 450081 1 WSR 1.908 X 2.41 X .03 SS
28 710353 2 SCR-MC 10-32 X .37 ZINC
29 710985 2 SC 3/8-16 X .62
30 711124 1 SCR-ST-B 10 X .37 NI
31 711506 2 WSR-FLT 5/16 (NARROW) ST PL
32 711512 1 WSR-FLT .75 X 1.37 X .08
33 711513 1 WSR-FLT .689 X 1.06 X .029 SS
34 711553 2 WSR-INT LOCK #10
35 712041 2 BLT-SHOULDER 1/4-20 X .44 X .3
36 712563 4 SCR-MC 1/4-20 X 1.00 SS
37 712667 4 NUT-HEX NYLOC 1/4-20 SS
38 712822 7 SCR-MC TR HD 10-24 X .50 SS
39 760220MCH 1 1.5 ADAPTER MCH
40 809413MCH 1 SOLUTION VALVE
41 828490 2 CLAMP-CRIMP 140R
42 828952 1 FITTING PP 1/4MPT 3/8BARB
43 828970 2 WSR NEOP 1.87X2.4X.125
44 828971 1 NUT 1 1/2 PIPE THREAD
45 828975 1 WSR NEOP .75X1.5X.09
46 829463 1 S S WASHER
47 830062 1 FITTING BRASS 90 3/8MPT 3/8FPT
48 832896 2 GUIDE WHEEL
49 832949 2 BRACKET BUMPER
50 833254 2 BUMPER WHEEL AXLE
51 833316 1 DRAIN PLUG
52 281637 1 HOSE-WIRE REINF 3/8 X 11"
PARTS LIST
SOLUTION AND RECOVERY TANK BOM (BRUSH DRIVE)
10

MAINFRAME ASSEMBLY (BRUSH DRIVE)
11

ITEM PART NO. REQ'D DESCRIPTION
1 210142 1 PEDAL PAD
2 260030 5 BUSHING-.5015 X .628 X .375 OI
3 260041 2 BUSHING-FLG .502 X .750 X .375
4 260043 1 LIFT ARM, LEFT SIDE
5 260044 1 LIFT ARM, RIGHT SIDE
6 260046 1 PEDAL BRACE
7 260054 1 PEDAL WELDMENT
8 260055PTD 1 LIFT HANDLE WELDMENT
9 260075 1 YOKE WELDMENT
10 260256 1 BASE 260TD CHAR GREY
11 260093 1 CHASSIS MMAN 260
12 260125 1 BUSHING-YOKE .407 X 1.687 STL
13 260128 1 SPACER-YOKE
14 260219 2 WHEEL-10" MOLD-ON ONLY
15 260136 2 WHEEL AXLE BKT ASY
16 260141 1 SPACER-LIFT ARM
17 260660 1 SQUEEGEE MECH ASSEMBLY
18 710196 4 SCR-MC 5/16-18 X .62
19 710986 2 SC 3/8-16 X 1 ZINC
20 710992 1 BLT-SHOULDER 1/2 X 1.25 X 3/8
21 711228 8 BLT-HH 5/16-18 X .75 STL ZINC
22 711232 4 BLT-HH 5/16-18 X 1.50
23 711242 8 BLT-HH 3/8-16 X 1.00
24 711250 2 BLT-HH 3/8-16 X 1.25 STL ZINC
25 711374 2 NUT-NYLOC 5/16-18
26 711375 2 NUT-NYLOC 3/8-16 1/2NUT
27 711380 2 NUT-NYLOC 3/8-16
28 711439 3 NUT-FLANGED WIZZ 3/8-16
29 711507 2 WSR-FLT .37 X 1.12 X .06
30 711512 8 WSR-FLT .75 X 1.37 X .08
31 711515 8 WSR-FLT .406 X .812 X .0625
32 711545 16 WSR-HELICAL 5/16
33 711546 12 WSR-HELICAL 3/8
34 711575 22 WSR-FLT .31 X .75 X .06 STL
35 711579 2 WSR-FLT .56 X 1.00
36 712081 2 BLT-SHOULDER 5/16-18 X .75 X .
37 712099PLT 2 BLT-SHOULDER 1/2 X 1/2
38 712310 6 WSR-FLT .52 X .87 X .06 PL
39 712680 4 NUT-HEX 5/16-18 SS
40 713045 1 BLT-HH 3/8-16 X 1.75 #5
41 713048 1 BLT-HH 3/8-16 X 2.50 #5
42 762107 2 SPACER-1.00 X 1.25 X .25
43 762340 2 BUSHING-.502 X .625 X .270 STL
44 809247 2 SPACER-.442 X .50 X .312
45 827110 2 CASTER 5 INCH
46 832829 2 NUT-U TYPE 5/16 X 18
47 710493 2 SCR-MC 4-40 X .75 PAN HD
48 711596 2 WSR-INT LOCK #4
49 711428 2 NUT-HEX 4-40
50 747603-1 1 SWITCH, MICRO 1.34" ROLLER ARM
PARTS LIST
MAINFRAME ASSEMBLY BOM (BRUSH DRIVE)
12

LINKAGE ASSEMBLY (BRUSH DRIVE)
13

ITEM PART NO. REQ'D DESCRIPTION ITEM PART NO. REQ'D DESCRIPTION
1 210066 2 DRIVE HUB RETAINER BLT 40 710823 2 SC 1/4-20 X .50 NYL
2A 260002 2 PAD HOLDER-26B 41 710986 8 SC 3/8-16 X 1 ZINC 2B 260003 2 BRUSH-FEED THRU BASSINE 42 711128 1 SCR-ST-B HI-LO 8 X .62 ZINC
2C 260004 2 BRUSH-26B NYL 43 711160 3 SCR-HI/LO #10 X 5/8 ZINC 2D 260005 2 BRUSH-POLY GRIT 26B 44 711161 2 SCR-HI/LO #10 X 3/4 ZINC
2E 260006 2 BRUSH-STRATAGRIT 26B 45 711203 6 BLT-HH 1/4-20 X .62
3 260009 1 BATTERY TRAY 46 711210 2 BLT-HH 1/4-20 X 1.25 STL ZINC 4 260030 8 BUSHING-.5015 X .628 X .375 OI 47 711228 2 BLT-HH 5/16-18 X .75 STL ZINC 5 260036 12 PIN, RETAINER 48 711316 2 NUT-HEX 1/4-20 ST PL 6 260038PTD 1 MOTOR MOUNT WELDMENT RH 49 711334 2 NUT-HEX 1/2-13 ST PL 7 260039PTD 1 MOTOR MOUNT WELDMENT LH 50 711368 2 NUT-WING NYLOC 1/4-20 PL 8 260041 13 BUSHING-FLG .502 X .750 X .375 51 711375 3 NUT-NYLOC 3/8-16 1/2NUT 9 260042 1 ACTUATOR BAR WELDMENT 52 711425 9 NUT-FLANGED WIZZ 1/4-20
10 260049 4 LINKAGE BAR 53 711505 7 WSR-FLT 1/4 11 260053 2 CABLE-PUSH / PULL 54 711510 1 WSR-FLT .50 X 1.37 X .10 12 260066 2 BUSHING-FLG .377 X .687 X .406 55 711517 2 WSR-FLT .77 X 1.37 X .03 13 260068 1 SPACER-SPRING 56 711524 2 WSR-WAVE .52 X .87 X .01 14 57 711544 6 WSR-HELICAL 1/4 15 260077 1 MOTOR FRAME WELDMENT 58 711545 2 WSR-HELICAL 5/16 16 260114 2 LINKAGE WELDMENT 59 711713 14 RET RING-E EXT .50 17 260123 1 CABLE BRACKET WELDMENT L.H. 60 711717 2 RET RING-E EXT .37 18 260124 1 CABLE BRACKET WELDMENT R.H. 61 712129 2 SCR-TR 1/4-20X 1.00 HWH 19 260137 1 SPRING-COMP .960 X 2.00 ZINC 62 712301 2 WSR-FLT .37 X .87 X .06 (WIDE) 20 260150 1 BATTERY LINER 63 712310 25 WSR-FLT .52 X .87 X .06 PL 21 260159 1 HOSE-VAC 1.5 X 78" WIRELOC 64 712667 1 NUT-HEX NYLOC 1/4-20 SS 22 210466 1 CABLE CONDUIT 65 740132 2 INSULATOR (GLASTIC) 23 260183 1 NUT 1/4 NPT NYL 66 740159 1 CIRCUIT BRKR-175 RED HOUSING 24 260203 1 CLAMP-HOSE 102120 MURRAY 67 740209 2 GEARMOTOR 24V 17B 25 260214 2 TANK CABLE ASY 260 68 740225 1 VAC MOTOR 6515-13 24V 26 260224 1 DRAIN HOSE 1/4 X 18 SILICONE 69 762073 1 BUSHING-.259 X .375 X .265 27 260315 1 LIFT CABLE BRACKET 70 762256PLT 2 NUT ADJ LH ZINC PLT 28 260337 1 SQUEEGEE CABLE 71 809444 1 CLIP-CORD 29 290017 1 MOULDED VAC MOTOR GASKET 72 828264 1 WASHER CUP 30 320248 2 CLEVIS, SLOTTED 73 828490 1 CLAMP-CRIMP 140R 31 320271 1 FITTING PP 90 3/8MPT 3/8HOSE 74 829067 2 CLAMP-CRIMP 560R 32 320272 2 NOZZLE BODY LOCKNUT 75 832996 1 TERMINAL BLOCK 2POLE VDE 33 320273 1 CLAMP-HOSE SHUT-OFF 76 833191 1 HOSE RUBBER FLEX 2X9 34 364-816 1 NUT-NYLOC 1/2-13 HALF 77 833265PLT 1 THREADED SPACER PLT ZINC 35 380064 1 RING, FOAM 78 833325 2 FITTING NYLON 90 1/4MPT 3/8HOSE 36 430035-1 2 DRIVE HUB W/ BRASS INSERT 79 833638 2 BRASS STUD 37 450038-H 2 Z BKT 5.7 VDE ZINC 80 833725 2 CLIP-T 38 450076 15 CLAMP-CRIMP 185R SS 81 840011 1 VAC MOTOR COVER TOP 39 710180 2 SCR-MC 1/4-20 X .75 ZINC 82 840012 1 VAC MOTOR COVER BOTTOM
PARTS LIST
LINKAGE ASSEMBLY BOM (BRUSH DRIVE)
14

CONTROL PANELS (BRUSH DRIVE)
15

ITEM PART NO. REQ'D DESCRIPTION ITEM PART NO. REQ'D DESCRIPTION
1 210045 1 CABLE-SOLUTION CONTROL 33 711671 1 PIN-CLEVIS .31 X 2.13 11-10 2 260053 2 CABLE-PUSH / PULL 34 711808 1 PIN-HAIRPIN COTTER #13 3 260066 4 BUSHING-FLG .377 X .687 X .406 35 712070 1 BLT-SHOULDER 5/16 X 3/4 X 1/4- 4 260069MCH 1 LEFT HANDLE MACHINED 36 712100 2 BLT-SHOULDER 3/8 X 2.25 5 260070MCH 1 RIGHT HANDLE MACHINED 37 712320 8 WSR .22 X .45 X .04 NYL 6 260081 1 CABLE MOUNT WELDMENT 38 712540 6 SCR-MC 10-24 X .37 SS TH 7 260084 1 DASHBOARD 39 712822 8 SCR-MC TR HD 10-24 X .50 SS 8 260099 1 CONTROL LEVER MOUNTING BRACKET 40 715608CE 1 DECAL-FORWARD TD CE 9 260173 1 ELECTRICAL BOX MTG 41 715602-1 1 DECAL, REVERSE ES260320
10 260255 1 SPEED CONTROL BRACKET 260TD 42 715603 1 DECAL-SQUEEGEE LIFT 260 11 260658 1 BKT, CIRCUIT BREAKER PANEL, ES320 43 715604 1 DECAL-SOLUTION 260 12 260284 1 REAR PANEL ASY 260TD 44 715605 1 DECAL-BRUSH POSITION 13 260286 1 SQUEEGE HANDLE WELDMENT 45 746006 1 CIRCUIT BRKR-3AMP PUSH BUTTON 14 260291 1 HANDLE GRIP 260TD 46 740132 2 INSULATOR (GLASTIC) 15 260325 1 HANDLE BRACKET 47 740247 1 CIRCUIT BREAKER-30AMP PUSH BUTTON 16 260337 1 CABLE-SQUEEGEE 48 740216 1 GUAGE BATTERY COND 17 320248 2 CLEVIS, SLOTTED 49 740241 1 CONTACT-24V 50AMP 18 281579 1 SQUEEGEE BLADE ASSY 32" 50 742266 1 CIRCUIT BREAKER-60AMP PUSH BUTTON 19 430051 2 SPRING-RETURN .313 X .438 X 2. 51 760286 1 WIRE FORMED HOOK 20 710178 4 SCR-MC TR HD 1/4-20 X .50 ZINC 52 762400 1 BUSHING-HEYCO 1-5/8 X 2-1/8 X 21 710180 17 SCR-MC 1/4-20 X .75 ZINC 53 788147 1 SOLENOID-24VDC 22 711125 2 SCR-ST-B 10 X .50 NI 54 809311 2 PIN-COTTER 7/64 X 1 23 711161 2 SCR-HI/LO #10 X 3/4 ZINC 55 747024 1 KEY SWITCH, SPST SOLDER LEADS 24 711368 2 NUT-WING NYLOC 1/4-20 PL 56 833102 1 SPRING-KNOB .60 X .73 X 1.75 Z 25 711373 1 NUT-NYLOC 1/4-20 57 833374 2 PIN-HAIRPIN COTTER 3/8 26 711420 2 NUT-HEX JAM 5/16-18 STPL 58 833638 2 BRASS STUD 27 711503 2 WSR-FLT #10 59 881002 2 PIN-CLEVIS 11-083 ZINC 28 711505 4 WSR-FLT 1/4 60 710493 2 SCR-MC 4-40 X .75 PAN HD 29 711523 4 WSR-WAVE .37 X .68 X .08 61 711596 2 WSR-INT LOCK #4 30 711544 4 WSR-HELICAL 1/4 62 711428 2 NUT-HEX 4-40 31 711575 1 WSR-FLT .31 X .75 X .06 STL 63 747603-1 1 SWITCH, MICRO 1.34" ROLLER ARM 32 711668 2 PIN-CLEVIS 3/8 X 1 11-141
PARTS LIST
CONTROL PANELS BOM (BRUSH DRIVE)
16

SOLUTION AND RECOVERY TANK (TRACTION DRIVE)
17