Minuteman M2400 Parts list manual

Parts and Instruction Manual
M2400 Electric Burnisher
W/ Dust Control Option

Parts
and Instruction Manual
This manual is furnished with each new MINUTEMAN M2400. This provides the necessary operating
and preventive maintenance instructions. Operators must read and understand this manual before operat-
ing or servicing this machine.
This machine was designed to give you excellent performance and efficiency. For best results and
minimal cost, please follow the general guidelines below:
· Operate the machine with reasonable care.
· Follow the manufacturers suggested maintenance instructions as provided in this booklet.
· Use original Minuteman supplied parts.
TECHNICAL SPECIFICATIONS
Model M2400
Model No. M17150-00, 01, 04, 05
M24000-00, 02, 04, 06
M24000-01, 03, 05, 07
M20150-01, 02, 03, 04
M17150-01CE, 05CE
M20150-02CE, 04CE
M24000-01CE, 03CE, 05CE, 07CE
Brush Speed
Brush Diameter
Horse Power
Voltage
Cable Length
PAMS Dust
Control
Wheels
Weight
Pad Housing
Handle
Circuit Breaker
Carbon Brush Light
Pad Pressure
15000 rpm
17” (43cm) or 20” (51cm)
1½ hp
115V or 240V
50’ (15m) 14-3
Option
6” (15cm)
84 lbs (38 kg)
Cast Aluminum
Dual switch w/ indicator
light
15 amp
Yes
Adjustable
2400 rpm
20” (51cm)
1½ hp
115V or 240V
50’ (15m) 14-3
Option
6” (15cm)
84 lbs (38 kg)
Cast Aluminum
Dual switch w/ indicator
light
15amp
Yes
Adjustable
1500-2400 rpm
20” (51cm)
1½ hp
115V or 240V
50’ (15m) 14-3
Option
6” (15cm)
84 lbs (38 kg)
Cast Aluminum
Dual switch w/ indicator
light
15amp
Yes
Adjustable
®

Parts
and Instruction
M
anual

Parts
and Instruction Manual
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS.............................................................................................. 1
INSPECTION........................................................................................................................................ 2
GROUNDING INSTRUCTIONS ........................................................................................................... 2
ELECTRICAL....................................................................................................................................... 2
115 Volt - M24000-00, 02, 04, 06; M17150-00, 04; M20150-01, 03 ................................................ 2
240 Volt - M24000-01, 03, 05, 07; M17150-01, 05; M20150-02, 04;............................................... 2
................M24000-01CE, 03CE, 05CE, 07CE; M17150-01CE, 05CE; M20150-02CE, 04CE ........ 2
Model 2400 Burnisher Operating Instructions ................................................................................. 5
Preventive Maintenance..................................................................................................................... 7
Trouble Shooting ................................................................................................................................ 7
Exploded Views .................................................................................................................................. 8
Base Assembly................................................................................................................................ 8
Base Assembly BOM ...................................................................................................................... 9
Handle Assembly .......................................................................................................................... 10
Handle Assembly BOM ................................................................................................................. 11
Dust Control Option....................................................................................................................... 12
Dust Control Option BOM ............................................................................................................. 13
Wiring Diagrams ............................................................................................................................... 14
Minuteman International Made Simple Commercial Limited Warranty........................................ 16

Parts and Instruction Manual
Page 1
FOR COMMERCIAL USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the
following:
READ ALL INSTRUCTIONS BEFORE USING
WARNING - To reduce the risk of fire, electric shock, or injury:
• Do not leave appliance when plugged in. Unplug from outlet when not in use and before
servicing.
WARNING
To reduce the risk of electric shock - Do not expose to rain. Store indoors.
• Never allow children or untrained adults to operate this equipment.
• Keep the area of operation clear of all persons, particularly small children, and pets. Keep
bystanders at least 25 feet away from the area of operation.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return it to a service center.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around
sharpedgesorcorners. Donotrunapplianceovercord. Keepcordawayfromheatedsurfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dustbag and/or filters in place.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas they
may be present.
• Connect to a properly grounded outlet only. See grounding instructions.
SAVE THESE INSTRUCTIONS

Parts and Instruction Manual
Page 2
INSPECTION
Carefullyunpackandinspect yourmachinefor shippingdamage.Each unitistested andthoroughly
inspectedbeforeshipment,andany damage is the responsibility of the delivery carrier who should
be notified immediately.
WARNING
• Read Instruction Manual before operating this piece of equipment.
• To reduce the risk of fire use only commercially available floor cleaners and waxes intended for
machine application.
• To reduce the risk of electrical shock, do not expose to rain. Store indoors.
• Electricalmotors and componentscan cause anexplosionwhenoperatednearvolatile materials
and vapors. Do not use this machine near flammable materials such a solvents, thinners, fuels,
grain dust, etc.
• Risk of explosion. Floor sanding can result in an explosive mixture of fine dust and air.
Use floor-sanding machine only in a well-ventilated area free from flame or match.
-
This floor machine is designed to operate on a standard 15 amp. 120 volt, 60 hz, AC circuit.
Voltages below 105 volt AC or above 125 volts AC could cause serious damage to the motor.
ELECTRICAL -
This machine is designed to operate on a standard 10 amp. 230 volt, 50 hz,AC circuit.
GROUNDING INSTRUCTIONS
• Thisfloorfinishingmachineshouldbegroundedwhileinusetoprotectthe operator from electric
shock. The machine is equipped with a three-conductor cord and a three-prong grounding type
attachment plug to fit the proper grounding type receptacle. The green (or green and yellow)
conductor in the cord is the grounding wire. Never connect this wire to other than the grounding
blade.
• Floor Finishing Machines Rated Less Than 150 Volts - If the machine is provided with an
attachment plug as shown in Sketch A it is intended for use on a 120-volt (nominal) circuit. If a
properly grounded receptacle as shown in Sketch A is not available, an adapter as shown in
Sketch C is available and should be installed as shown in Sketch B if the outlet box that houses
the receptacle is grounded. Be sure to fasten the grounding tab with the faceplate screw.
115 Volt - M24000-00, 02, 04, 06; M17150-00, 04; M20150-01, -03
ELECTRICAL
240 Volt - M24000-01, 03, 05, 07; M17150-01, 05; M20150-02, 04;
M24000-01CE, 03CE, 05CE, 07CE; M17150-01CE, 05CE; M20150-02CE, -04CE

Parts and Instruction Manual
Page 3
POUR USAGE COMMERCIAL SEULEMENT
MODE D’EMPLOI SECURITAIRE
Lorsque l’on utilise un appareil électrique, des précautions de base doivent toujours être suivies
telles que:
BIEN LIRE LE MODES D’EMPLOI AVANT USAGE
AVERTISSEMENT - Pour réduire les risques de feu, choc électrique ou blessure:
• Ne pas quitter l’appareil lorsque la prise de courant est branchée. Débrancher de la sortie
électrique lorsque la machine n’est pas en usage ou pour en faire le service.
AVERTISSEMENT
Pour réduire le risque de choc électrique - Ne pas exposer à la pluie - Entreposer à l’intérieur.
• Ne jamais laisser des enfants ou des adultes inexpérimentés faire fonctionner cet appareil.
• Garder la zone de fonctionnement libre de toute personne, particulièrement les petits enfants
et les animaux. Garder les spectateurs à une distance d’au moins 7,6 mètres (25 pieds) de la
zone de fonctionnement.
• Utilisertelqueprescritdanslelivred’opération etseulementaveclesattachementsrecommendés
par le manufacturier.
• Ne pas s’en servir avec corde ou prise de courant endommangée. Si l’appareil ne fonctionne
pas ou a été échappé, endommagé, entreposé à l’extérieur ou déposé dans l’eau, l’appareil
devrait être envoyé à un département de service pour inspection.
• Ne pas tirer ou porter par le câble ou se servir du câble comme poignée. Ne pas fermer de
portes sur le câble ou tirer le câble près d’objets pointus. Ne pas conduire l’appareil écrasant le
câble et soyez certain de protéger le câble entre toutes surfaces de chauffage.
• Ne pas débrancher en se servant du câble. Pour débrancher tirer sur la prise et non sur le
câble.
• Ne pas manipuler la prise ou l’appareil avec les mains mouillées.
• Ne placer aucun objet dans la sortie et ne pas s’en servir si la sortie est obstruée. Eliminer toute
poussière, maillon, cheveux ou quoique ce soit qui pourrait réduire le mouvement d’air.
• N’exposer aucun cheveux, vêtement, doigts ou autres aux ouvertures de l’appareil.
• Ne rien ramasser de ce qui brûle ou de fumée tels que cigarettes, allumettes ou cendres en feu.
• Ne pas employer sans filtre de poussière ou autre en position.
• Fermer tous les contrôles après utilisation.
• Soyez très prudent lors du nettoyage d’escaliers.
• Ne pas ramasser de liquide inflammable ou combustible tel que gazoline et ne pas utiliser dans
les endroits ou ces derniers pourraient être présent.
• Brancherdans une prise avec une prise de terre seulement. Voir références pour prise de terre.
CONSERVEZ CES RECOMMANDATIONS
DE MODE D’EMPLOI

Parts and Instruction Manual
Page 4
INSPECTION
Déballer soigneusement en constatant s’il y, a lieu tout dommage apparent. Chacune des pièces
d’équipement est entièrement inspectée à l’usine et tout dommage de transit est la responsabilité de la
compagnie de transport qui devrait être prévenue immediatement.
AVERTISSEMENT
• S.V.P. lire le manuel d’instruction avant d’opérer cette pièce d’équipement.
• Pour réduire le risque d’incendie, se servir de ces appareils uniquement pour usage commercial et
avec les produits contruits spécifiquement pour usage avec ces appareils.
• Les moteurs électriques peuvent être la cause d’explosion si ils sont utilisés près de matériaux ou de
vapeurs explosives. Ne pas opérer près de matériaux inflammables tels que solvant, essence,
poussière de grain etc.
ELECTRICITE - 115 Volt Modèles M17120-00, 01, 02 M20120-01, 02, 03
Ces appareils sont congus pour opérer sur un circuit standard de 15 amp, 120 volt, 60 hz, circuitAC.
Tout voltage en bas de 105 voltAC ou au-delà de 125 voltsAC pourrait occasionner des dommages au
moteur.
ELECTRICITE - 230 Volt Modèles M17240-01, 02, 03 M20240-01, 02, 03
Cesappareilssont congus pour opérer sur un circuitstandardACde 16amp, fusible type L230volt,50
hz.Tout voltageen bas de 200 voltACou au-delà de 250 voltsAC pourraitoccasionnerdes dommages
au moteur.
INSTRUCTIONS POUR PRISSE DE TERRE
• Ces appareils doivent posséder une prise de miss à terre pour protéger l’opérateur contre les chocs
électriques.Cetappareilest muni d’une corde électrique à trois fils et d’unreceptacleà trois fourchons
et prise de mise à terre pour s’accorder dans un receptacle avec prise de mise à terre réciproque. Le
fil conducteur vert (ou vert et jaune) de la corde électrique est le fil designé comme prise de mise à
terra. Ne jamais relier ce fil à un fil autre que celui de prise de mise à terre.
• Appareils estimés à moins de 150 volts - Si ces appareils offrent une prise de courant tel que dans
le croquisA, ils sont destinés pour utilisation avec un circuit de 120 volts. Si un receptacle avec prise
de mise à terre n’est pas disponible tel que montré au croquisA, un adapteur tel que vu au croquis C
est disponible et devrait être installé tel que montré au croquis B si la boite électrique est munie d’une
prise de mise à terre. Assurez-vous de bien relier la patte de prise avec la vis.
• Appareilsdestinésà plus de 150 volts-Si ces appareilsoffrent uneprisede courant tel que demontré
au croquis D, ils doivent être utilisés avec un circuit de 240 volts. Aucun adapteur n’est disponible
pour cette prise.

Parts and Instruction Manual
Page 5
Hand Tighten or push in. DO NOT FORCE.
Safety Interlocking switches.
Pad Pressure Adjustment Knob. When using new pad, turn
Install 20 Inch Pad inside pad driver.
Hand Tighten center clip or push straight in.
Model 2400 Burnisher Operating Instructions
1. Install the polishing pad on to the pad driver. Make
sureyourinstallingatrue20” polishing type pad.Then
install the locking centering device cup by lining up
the threads on the pad driver and the cup and push
straight down, or just screw the cup devise onto the
pad driver. Hand tighten the cup to the pad driver. Do
notforcethecenteringcupifcross-threaded. Because
of patented centering cup Just hit the high side of the
cup with the palm of your hand to straighten out the
crossthreadingproblem.Toremovethecentering cup
hold onto it with one hand and with the other hand
spin the pad driver in the opposite direction until the
cup is removed.
2. Plug the machine into a standard 115-volt grounded
wall outlet. If an extension cord is required, it must
be 3-wire cord. The burnisher is equipped with a 3
wire, 14-gauge cord, 50 feet long. If the extension
cord to be used is more than 25 feet a larger wire
size cord should be used, preferably a 12- gauge
cord no longer than 50 feet long. Failure to use a
lager size cord may result in reduced performance
and motor overheating. After the cord is properly
plugged into the outlet a red light will illuminate on
the rear of the operators handle telling the operator
you now have power to the machine.
3. After the pad is on the machine stand the burnisher up straight on top of the pad so it is flat on the
floor. If you are starting with a new pad, decrease the pad pressure adjustment centering wheel as far
as it can go. This will raise your pad to the highest position. Next by stepping onto the foot locking
lever, located on the right side of the machine, push downward with your foot to release the handle.
Whilethe handleis lowereddown take oneof yourthumbs andpull eithersafety interlockingswitches,
located at the top of the handle, with you fingers grab the lever switch and pull at the same time.
CAUTION: This machine has a high starting torque. Have both hands on the control handle when
starting to ensure complete control.

Parts and Instruction Manual
Page 6
Model 2400 Burnisher Operating Instructions
4. After the machine has started the pad pressure gauge, located at the backside near the rear of the base, should
be reading at the top of the white zone, or telling the operator the pad is off the floor. Now, to increase the pad
pressure keep the burnisher running with one hand and pushing the machine in a back and forth motion. With
the other hand turn the center adjustment knob, in the center of the base, to the increase clockwise position
until the gauge gets to the 15 amp red line. After the meter needle reads between the lower edge of the red
zone, or 15 amps, you have reached the proper polishing pressure. If the burnisher runs over a high spot, the
gauge needle will go into the top of the red zone, but should fall back into the safety-working zone as you go
along.As the pad is being used more pad pressure will be required just by running the machine back and forth
and screwing the adjustment knob to the increase position until the needle reaches 15 amps, or the bottom of
the red safety working zone. If the operator works too long in the red zone the machine will trip the thermo-reset
breaker located at the rear base of the machine. To prevent it from happening again adjust the pad pressure
screw knob counter clockwise to decrease pad pressure.
5. The machine should always be started with the pad
pressure fully decreased when using a new pad, and
then adjusted to the correct pad pressure.
6. Burnish with the machine in a straight line. The pace
ofthe machine shouldbe determinedby the condition
of the floor. Normally the machine can be operated at
a slow to medium walking pace. Overlap with the pad
driver approximately 2” to 3” when making a pass.
For the ease of use, start nearest the wall outlet and
work away from this point. CAUTION: Do not let the
machinesit in one spotfor more than5to 10 seconds.
Due to the high RPM’s of this machine and the heat it
develops, sitting in one spot longer than this may
damage the floor finish and possible the floor itself.
7. The machine employs an adjustable spring loaded
center caster directly in the center of the pad driver.
Thiscasterispresetatthe factory to have the machine
operate at 14.0 to 14.5 amps. If the machine circuit
breaker trips, or the wall circuit breaker trips, adjust
thecenterwheelcasterto“decrease”thepadpressure
on the floor. If the machine is not properly burnishing
the floor with full pad contact, adjust the caster to
“increase” the pad pressure on the floor.
8. This machine employs a motor carbon brush wear
indicatorlightlocated on the rearbaseof the machine.
Thislight willilluminate when the brushes are worn to
the point where there is approximately 250 hours
remaining. The carbon brushes should be replaced
shortly after this light indicates excessive wear.
Pad Pressure Gauge. Needle will “peg” then drop to its normal
pressure. Adjust pad pressure knob so pad pressure gauge reads
at the 15 amp red line. Be sure to keep unit moving to prevent
damage to the floor.
Pad Pressure Gauge
Circuit Breaker
Carbon Brush Wear Indicator Light

Parts and Instruction Manual
Page 7
Model 2400 Burnisher Operating Instructions
Preventive Maintenance
1. Inspectmotor carbon brushes approximately every 250 hours.Aset of carbon brushes should
last as long as 2500 hours. Premature wear may indicate other problems with the motor.
Thesecanbeinspectedby removing the motor cover.Indications for changing carbon brushes
would be if the indicator light comes on or if the carbon brushes are flush with or slightly
recessed in the brass brush holder.
2. Periodically clean the motor by removing the motor cover and blowing it out with compressed
air.
3. Check the drive belt of wear and proper tension. Retention the belt by loosening the four
motor mount screws, then apply force to the motor toward the rear of the machine. Take out
excessive slack. Do not overtighten the belt. This can cause excessive loads to the bearings
and reduce the belt life.
Trouble Shooting
1. Machine will not start.
A. Check to see if the machine circuit breaker is reset.
B. Check to see if there are any disconnected wires at the motor or switches.
C. Check to see if the “on/off” switch and safety switch are activating.
2. Motor will not start, circuit breaker trips.
A. Check rectifiers in the motor for damage.
B. Inspect internal wiring for loose connections or direct shorts.
C. Inspect carbon brushes for excessive wear.
3. Machine runs a short period of time, then the circuit breaker trips.
A. Check motor carbon brushes for wear.
B. Adjust pad pressure to the floor to relieve pad pressure.
C. Extension cord under size, pulling a low voltage.

Parts and Instruction Manual
Page 8
Exploded Views
Base Assembly

Parts and Instruction Manual
Page 9
Item Part No. Qty. Description
1 130040PTD 1 Handle PTD DK Grey
1A* 130040CTD 1 Handle - Coated
2 150208 1 Motor Bracket 56/56 Frame
3 150209 2 Foam Tape 25 in.
4 230002 1 Housing Plate
5 230003 1 Housing Plate Gasket
6 230004 1 Curved Sealing Plate 17"
6A 230022 1 Curved Sealing Plate 20"
7 230005 1 Rear Closure 17"
7A 230023 1 Rear Closure 20"
8 230006 1 Motor Shroud
9 230010 1 Release Pedal Weldment
10 230013 1 Axle
11 230016 1 Release Weldment
12 230017PTD 1 Base Casting 17" Painted
12A* 230017PTDCE 1 17" Casting CE Painted
12B 230020PTD 1 Base Casting 20" Painted
12C* 230020PTDCE 1 20" Casting CE Painted
13 230019 1 Clamp Band Assy. 17" HS
13A 230030 1 Clamp Band Assy. 20" HS
14 230021 1 Dust Skirt 17" HS
14A 230037 1 Dust Skirt 20" HS
15 230024 1 Spring Bracket
16 230031 1 Non-Skid Strip
17 230036 1 Foam Gasket
18 230038 1 Shielding Bracket
19* 230040 1 Line Filter Bracket
20 230043 2 Wheel, 6” w/Nylon Brushing
21 260581MCH 1 Pad Grabber, Ring Machined
22 430051 1 Spring-Return .313x.438x2.
23 450050 1 Bushing - Heyco .875x.875x1.
24 710196 2 SCR-MC 5/16-18x.62
25* 710360 2 SCR-MC 10-32x1 Zinc
26 710579 2 SCR-MC 1/4-20x.62 Zinc
27 710985 2 SC 3/8-16 x .62
28 710986 4 SC 3/8-16 x 1 Zinc (1500 rpm)
28A 711246 4 BLT-HH 3/8-16 x .87 (2400 rpm & V.S.)
29 710987 2 SC 3/8-16 x 1.50 Zinc
30 711142 11 SCR-ST-F 10-24 x .37 Zinc
31 711243 1 Bolt-HH 3/8-16 x 1.50 STL Zinc
32* 711350 2 Nut-Nyloc 10-32
33 711379 1 Nut-Flanged Wizz 5/16-18
34 711380 2 Nut-Nyloc 3/8-16
35 711387 2 Nut-Nyloc 1/4-20 1/2Nut
36 711400 1 Nut-Pipe Lock 1/2
37 711508 4 WSR-FLT .44 x 1.00 x .08
38 711512 3 WSR-Flat .75 x 1.37 x .08
39 711515 2 WSR-Flat .406 x .812 x .0625
40 711519 2 WSR-Flat .25 x 1.01 x .06
41 711524 4 WSR-WAVE .52 x .87 x .01
42 711544 2 WSR-Helical 1/4
43 711553 3 WSR-Internal Lock #10
44 711555 4 WSR-Internal Lock 3/8 (1500 rpm)
44A 711556 4 WSR-Lock Internal 1/2 (2400 rpm &
V.S.)
45 711592 3 WSR-FLT .50 x .90 x .075 NYL
46 712081 1 BLT-SDR 5/16-18 x .75
47 712822 1 SCR-MC TR HD 10-24 x .50 SS
48 713002 2 BLT-HH 1/4-20 x .75 #5
49 715061 1 Decal, General Warning
50 715067 1 Decal, Brush Wear Indicate
51 710159 1 Decal, 1500
51A 715193 1 Decal, 2400
52 715234 1 Decal-Pad Pressure
Item Part No. Qty. Description
53 740044 1 Cap-Wire 12-18 74B
54 740220 1 Circuit Breaker 20AMP 2-Terminal 115V
54A 740106 1 Circuit Breaker 9AMP Push Button
240V
54B 741400 1 Circuit Brkr 10A Push Btn (Norway)
55 742115 1 Motor 1.5 HP 115V 66 Frame E623
55A 742230 1 Motor 1.5 HP 230V 66 Frame
56* 742254 1 RFI Shield Torroid
57* 742256 1 RFI Filter
58 742260 1 Triac ControlAsy. 115V
58A 742261 1 Triac ControlAsy. 230V
59 190031 1 Knob
60 230039 1 Heat Sink 2400
61 710377 1 SCR 1/4-20 x .37 Zinc
62 712666 1 Nut-Hex Jam 1/4-28 SS
63 715191 1 Decal - Speed Control
64 760028 1 Pulley MTR 4” ODX .62ID (1500 rpm)
64A 832409 1 Pulley (2400 rpm & V.S.)
65 760401 1 Center Cup New Style
66** 762160 4 Carbon Brush 115V
66A** 740281 4 Motor-Brush Carbon 240V
67 762318PLT 1 Sleeve .375 x .623 x .75
68* 762410 2 Bushing-.20x.312x.265 Alm
69 77-81-A 2 Spacer .53x.75x.25
70 829014 2 Flanged Bushing
71 829194 1 Top Cover w/Screen Print
72 832122 1 Spacer .384x.50x.31
73 832480 1 CasterAsy Complete
74 711319 1 Nut-Hex 5/16-18 ST PL
75 712533 1 SCR-MC 10-24 x 1.25 SS
76 712638 1 Nut-Hex 10-24 SS Nyloc
77 712763 2 Bearing Race Washer SS
78 712764 1 WSR #10 SS
79 762018 1 Caster Center
80 787791 1 Brush Shaft
81 831089 2 Shaft Bushing .375x.56x.75
82 831542 1 Spring .31x.42x1.5
83 832186 1 Thrust Bearing
84 832418 1 Adjustment Knob 5/16x18
85 832448 1 Shoulder Screw
86 832453 1 SCR-ADJ 5/16x18
87 833102 1 Spring-Knob .60x.73x1.75 Z
88 833224 1 Caster Weldment Yoke SS
89 833368 1 Bushing-Cast .203x.4995x.7
90 833507PLT 1 Cap Nut M2300PLT
91 880023 1 Nut-Nyloc 3/4x16
92 832552 1 Meter 115V 25 AMP w/Clip
92A 832819 1 Meter 230V 0-15 AMP
93 832603 1 Decal-CB Reset
94 832619 1 Spring
95 832623 1 Spring Clamp
96 832829 2 Nut-U Type 5/16x18
97 832859-1 1 Indicator Light 115V Asy
97A 742313-1 1 Lamp Assy 230V VDE
98 833073 1 Belt A38 (1500 rpm)
98A 832574 1 Belt V (2400 rpm & v.s.)
99 833199 1 MultiFlex 17" Assy.
99A 833900 1 MultiFlex 20" Assy. New
100 833212 1 PulleyAsy w/Bearings
101 833122 1 Drive Pulley Machined
102 881060 2 Bearing 3/4”
103 881317 2 Ret. Ring
104 833823 1 Dome Plug 2” Black
Base Assembly BOM

Parts and Instruction Manual
Page 10
Handle Assembly

Parts and Instruction Manual
Page 11
Item Part No. Qty. Description
1 150002 1 Cord-14GA-3 50FT Med Grey
1A 740600 1 Cord-European F3 G1.5MM 50Ft B
2 150003 1 Strain Relief 100x50
2A 150004 1 Strain Relief Heyco 3251
3 170040PLT 1 Cord Hook Plated
4 190006 2 End Cap
5 190008 1 Switch Cap
6 190009B 2 Safety Button Black
7 190010 1 Strain Relief
8 190015 2 Trigger Spring
9 190016 2 Foam Grip 4 1/2 I/L
10 190022 1 Switch Box Front Cover Black
11 190023 1 Switch Box Back Cover Black
12 190024 1 Electrical Box Cover Black
13 190029 2 Bushing .270 x .343 x 1.250
14 190033B 2 Switch Trigger Long Black
15 230025 1 Tube Handle
16 230027 1 Yoke Weld
17 710186 2 SCR-MC TR-HD 1/4-20 x 2 1/4
18 710380 2 SCR-MC 1/4-20 x .75 Zinc
19 711128 4 SCR-ST-B HI/LO 8 x .62 Zinc
20 711160 4 SCR-HI/LO #10 x 5/8 Zinc
21 711162 4 SCR-HI/LO #10 x 1 1/2 Zinc
22 711214 2 Bolt-HH 1/4-20 x 2.00 STL Zinc
23 711316 2 Nut-Hex 1/4-20 ST PL
24 711373 2 Nut-Nyloc 1/4-20
25 711387 2 Nut-Nyloc 1/4-20 1/2Nut
26 711400 1 Nut - Pipe Lock 1/2
27 711504 2 WSR-Flat 1/4 SS
28 711554 4 WSR-INT Lock 1/4
29 711619 2 Roll Pin 1/8 x 1 3/5
30 711620 2 Roll Pin .25 x 1.25
31 715175 1 Decal - MMAN Runner
32 715237 1 Decal - Read Instruction
33 715501 1 Decal - Made in USA
34 715950 1 Label - Patent Numbers
35 740029 2 Switch - Snap SPST PB NO/NC
36 740361 1 Wire Assembly 14G White 6.00"
37 740362 1 Wire Assembly 14G Black 6.00"
38 741129 3 Splice, Crimp, End
39 742259 1 CableAssy, 2400 Handle
40 742313 1 Lamp-230V VDE
40A 832859 1 Indicator Light (115V)
Handle Assembly BOM

Parts and Instruction Manual
Page 12
Dust Control Option

Parts and Instruction Manual
Page 13
Item Part No. Qty. Description
1 230034 1 Dust Tube
2 230101 1 Hose 2” C/L 14”
3 380035 1 Gasket 4.31 x 5.81 x .19
4 390061 1 O-Ring - Valve Stem
5 710197 2 SCR-SC 5/16-18 x .75
6 710556 2 SCR-MC 10-32 x .75 Zinc
7 711202 1 BLT-HH 1/4-20 x .50 STL Zinc
8 711350 2 Nut-Nyloc 10-32
9 711505 1 WSR-Flat 1/4
10 711524 1 WSR-Wave .52 x .87 x .01
11 711594 1 WSR-Flat .56 x .88 x .03 Nickel
12 711903 1 Rivet-Pop .19 x .25 AL
13 715100 1 Decal - Pams Light Grey
14 762131PTD 1 Hose Fitting D/C 2300
15 762132 1 Dust Collection Tray
16 762396B 1 Filter Housing Burgundy
17 762403 1 Filter Pad 9” 5per
18 762404 1 Filter Gasket
19 762409PLT 1 Thrd Pin Retainer Zinc PL
20 462410 1 Bushing .20 x .312 x .265 ALM
21 762411 1 Gasket - Dust Collection
22 762415 1 Filter Housing Cover
23 762416PLT 1 Threaded Spacer Plated
24 805042 3.166 Ft Gasket
25 833214 1 Knob - 3 Sided 1/4 20 Insert
Dust Control Option BOM

Parts and Instruction Manual
Page 14
Wiring Diagrams

Parts and Instruction Manual
Page 15

Minuteman International, Inc. warrants to the original purchaser/user that the product is free from defects in
workmanship and materials under normal use. Minuteman will, at its option, repair or replace without charge, parts
that fail under normal use and service when operated and maintained in accordance with the applicable operation and
instruction manuals. All warranty claims must be submitted through and approved by factory authorized repair
stations.
This warranty does not apply to normal wear, or to items whose life is dependent on their use and care, such as belts,
cords, switches, hoses, rubber parts, electrical motor components or adjustments. Parts not manufactured by
Minuteman are covered by and subject to the warranties and/or guarantees of their manufacturers. Please contact
Minuteman for procedures in warranty claims against these manufacturers.
Special warning to purchaser -- Use of replacement filters and/or prefilters not manufactured by Minuteman or its
designated licensees, will void all warranties expressed or implied. A potential health hazard exits without original
equipment replacement.
All warranted items become the sole property of Minuteman or its original manufacturer, whichever the case may be.
Minuteman disclaims any implied warranty, including the warranty of merchantability and the warranty of fitness for a
particular purpose. Minuteman assumes no responsibility for any special, incidental or consequential damages.
This limited warranty is applicable only in the U.S.A. and Canada, and is extended only to the original user/purchaser
of this product. Customers outside the U.S.A. and Canada should contact their local distributor for export warranty
policies. Minuteman is not responsible for costs or repairs performed by persons other than those specifically
authorized by Minuteman. This warranty does not apply to damage from transportation, alterations by unauthorized
persons, misuse or abuse of the equipment, use of non-compatible chemicals, or damage to property, or loss of
income due to malfunctions of the product.
If a difficulty develops with this machine, you should contact the dealer from whom it was purchased.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some
states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions and limitations may not apply to you.
Cord Electric Group………. Three years parts, two years labor, ninety days travel (Not to exceed two hours)
Exceptions………. Port-A-Scrub, one year parts, six months labor
MPV 13, one year parts
MPV 14 and 18, two years parts, one year labor
RapidAir blower, one year parts, one year labor
Explosion-Proof Vacuum, one year parts, one year labor
Pneumatic Vacuums, three years parts, one year labor
Battery Operated Group…..Three years parts, two years labor, ninety days travel
(Not to exceed two hours)
Exceptions……Sweepers, one year parts, one year labor, ninety days travel
(Not to exceed two hours)
Internal Combustion Group….One year parts, one year labor, ninety day travel
(Not to exceed two hours)
Replacement Parts……………..Ninety days
Batteries………………………….0-3 months replacement, 4-12 months pro-rate
Polypropylene Plastic Tanks…Ten years, no additional labor
111 South Rohlwing Road · Addison, Illinois 60101 USA
Phone [phone] · Fax [phone]
E-Mail, www.minutemanintl.com
A Member of the Hako Group
Minuteman International Made Simple Commercial Limited Warranty
988563
Rev A 02/07