Minuteman TRS17-220 Parts list manual

Parts and Instruction Manual
TRS17-220 Total Recovery System

Parts and Instruction Manual - TRS17 Total Recovery System
Parts and Instruction Manual - TRS17 Total Recovery System
Total Restroom System
SPECIFICATIONS:
Model TRS17-220
Solution Tank 17 gallon
Recovery Tank
Vacuum Motor
Pump
Water Lift
Tank Construction
Baseplate
Rear Wheels
Casters
Power Cord
Dimensions
Weight
Electrical Draw
Vacuum Hose
Solution Hose
Wand
Pressure Gun
Fixture Drying Hose
15 gallon
Single 3-stage
600 psi/.85 GPM – 480 psi nozzle
120”
Polyethylene
¼” aluminum
10” non-marking
4” locking
50 ft.
39”H x 37”Lx 22”W
108 lbs.
12.5 amps
30’
35'
Swivel wand withsqueegee/brush head
Included
45’ x 1.25” Diameter
Technical Specications
Model:
TRS17-220
Technical Specications
Model:
TRS17-220

Parts and Instruction Manual - TRS17 Total Recovery System
INSPECTION...............................................................................
SAFETY INSTRUCTIONS...........................................................
GROUNDING...............................................................................
MAINTENANCE...........................................................................
MACHINE OVERVIEW.................................................................
OPERATION.................................................................................
UPPER ASSEMBLY.....................................................................
UPPER ASSEMBLY BOM...........................................................
UPPER ASSEMBLY BOM (PAGE 2)...........................................
LOWER ASSEMBLY....................................................................
LOWER ASSEMBLY BOM (PAGE 1)..........................................
LOWER ASSEMBLY BOM (PAGE 2)..........................................
LOWER ASSEMBLY BOM (PAGE 3)..........................................
INCLUDED ACCESSORIES........................................................
WARRANTY.................................................................................
4
5
7
8
10
12
16
17
18
19
20
21
22
23
24

Page 4
Parts and Instruction Manual - TRS17 Total Recovery System
INSPECTION
Page 4
Parts and Instruction Manual - TRS17 Total Recovery System
INSPECTION
UNPACKING YOUR NEW :
When your package is delivered, check the carton carefully for signs of rough handling. If your 
is damaged, notify the carrier immediately and request an inspection. Be sure to keep the carton,
packing inserts, packing lists and carrier’s receipt until the inspector has verified your claim.
MINUTEMAN’s liability ceases when the carrier picks up the shipment. However, our customer service
staff will be happy to furnish any information needed in connection with the claim and will attempt to
expedite a resolution.
PLEASE READ BEFORE OPERATING YOUR NEW :
Read the manual carefully and completely before attempting to operate the unit. This manual has
important information for the use and safe operation of the machine. Keep this manual handy at all
times.
This equipment has been engineered and manufactured to provide excellent performance and service.
To
ensure that your equipment will continue to perform as intended:
tMaintain equipment regularly- following the suggested maintenance schedule provided.
tUse only original MINUTEMAN parts when servicing.
tOperate equipment with care.
If additional information is needed, please contact:
MINUTEMAN INTERNATIONAL 630- 627-6900
ll information and specifications printed in the manual are current at the time of printing;
however because of MINUTEMAN’s policy of continual product development, we reserve the right
to make changes at any time without notice.

Page 5
Parts and Instruction Manual - TRS17 Total Recovery System
SAFETY INSTRUCTIONS
Page 5
Parts and Instruction Manual - TRS17 Total Recovery System
SAFETY INSTRUCTIONS
'"*-63&50$0.1-:8*5)5)&FOL LOWING WARNINGS AND
INSTRUCTIONS WILL VOID THE WARRANTY.
WARNING!
tThe machine was designed for use on hard surfaces, applications as per instructions and
recommendations written in this manual. Any deviation from its proper use or purpose and the
consequential damage that may occur is the sole responsibility of the end user.
tDisconnect the power cord from the outlet before servicing. Do not leave machine connected to an
electrical outlet when unattended.
tDo not immerse or use this machine in standing water. Such use may cause electric shock.
tWhen using an extension cord, use only a 3-prong conductor grounding cord-12 gauge wire or
heavier.
tTo avoid electric shock, do not expose the unit to rain or snow. Store it indoors in a heated location
only.
tDo not use the machine for dry vacuuming.
tUse defoamer at all times to prevent damage to the vacuum motor.
tDo not use water in excess of 130°F (54°C) in the solution tank
tTo prevent seal damage and chemical build-up to the pump system, run clean water through the
solution lines after each day’s use.
tUse only commercially available carpet cleaning solutions and defoamer intended for use with
machines of this type. Do not use dyes, bleaches, ammonia, or other additives.
tThe use of powdered cleaning solution, if not diluted properly, may result in damage to the pump.
Powdered chemical is not recommended. If powdered chemicals are used, premix in a separate
container before placing in the solution tank.
tAlways read and understand your chemical’s MSDS (Material Safety Data Sheet) before use.
tThis equipment is not designed to handle or use combustible/volatile substances such as gasoline or
kerosene, in, on, or near the machine. The use of such materials will cause extreme hazardous
condition.

Page 6
Parts and Instruction Manual - TRS17 Total Recovery System
Page 6
Parts and Instruction Manual - TRS17 Total Recovery System
tDo not expose machine to freezing temperatures.
tAll repairs must be done by an authorized MINUTEMAN repair station.
tDo not use replacement parts other than original MINUTEMAN parts.
tDo not allow your spray stream to remain in one fixed location as surface damage may occur.
tCheck that all spray nozzles are securely fastened. Loose nozzles could be ejected from equipment at
high speeds.
tPrevent burns by wearing gloves or using a barrier to remove hot quick disconnects.
tThis is not a toy. Keep away from children.
tDo not pull by the power or use power cord as a handle. Always unplug by grabbing the plug and
pulling, do not unplug by pulling the power cord.
tInspect cord for damage. Do not use damaged cords. Connect only to properly grounded outlets.
tKeep hair, fingers, loose clothing, and body parts away from moving parts and openings.
tTurn off all controls before disconnecting machine
tUse caution with ejected liquid or chemicals. High pressures and temperatures could be hazardous to
nearby people or surroundings.
ELECTRICAL - 220 Volt
Model: TRS17-220V
This machine is designed to operate on a standard 220 volt, AC circuit.

Page 7
Parts and Instruction Manual - TRS17 Total Recovery System
GROUNDING
Page 9
Parts and Instruction Manual - TRS17 Total Recovery System
GROUNDING
GROUNDING INSTRUCTIONS:
This piece of equipment must be grounded. Should an electrical malfunction occur, grounding
provides a path of least resistance for electrical current- reducing the risk of electric shock. This piece
of equipment is furnished with a cord that has a grounding conductor and grounding plug. The
grounded plug must only be plugged into an appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
WARNING:
Connecting the equipment to an improperly grounded outlet can result in an increased risk of electric
shock. A qualified electrician should be consulted if you are unsure that the outlet is properly grounded.
Do not modify the plug provided with the equipment. If it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
This appliance is designed for use on a 220-volt circuit.
Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong plugs
and outlets. DO NOT use extension cords more than 25 feet (7.6 m) long

Page 8
Parts and Instruction Manual - TRS17 Total Recovery System
MAINTENANCE
Page 10
Parts and Instruction Manual - TRS17 Total Recovery System
MAINTENANCE
MAINTENANCE:
This TRS-17 has been engineered and built to require minimum maintenance. But like any machine, it
does require some care to keep it in optimum working condition. Careful attention to these maintenance
instructions will give you maximum operating performance and life expectancy of the machine.
CAUTION: Disconnect the power cord from the outlet before doing any clean up or maintenance
on the machine
1. Keep the machine clean. Do not allow dust to accumulate on external surfaces or near any moving
parts.
2. After every job, wipe down the surface of the machine with a clean damp cloth.
3. Inspect cord for damage. Do not use machine with a damaged cord.
PERIODIC MAINTENANCE
tUse only chemicals safe for extractors
tAdhere to the appropriate mix ratios for all chemicals
tDo not add chemical to the solution tank- use the chemical feed system or pre-spray
tFor optimal performance, it is suggested that the operator flush the system after every job or at the
end of the day.
tPump seals and valves may need to be replaced at the 1000 hour mark if a loss in pressure is noted
tThe pressure regulator may require servicing should a pressure drop be noted
Daily:
tFlush chemical lines with water by placing clean water in the solution tank and using the pump to
spray.
tCheck and clean vacuum filter
Weekly:
xCheck for obstructions in vacuum pathways
xQuarterly:
xCheck pump, plumbing and fittings for leaks
xCheck power cords and hoses for tears
xCheck and clean solution filter

Page 9
Parts and Instruction Manual - TRS17 Total Recovery System
Page 11
Parts and Instruction Manual - TRS17 Total Recovery System
CORD STORAGE:
While not in use, storage can be accomplished by winding cord around handle assy. Cord should be
completely unwound during operation.
CORD SAFETY
xDo not leave appliance when plugged in. Unplug from outlet when not in use and before
servicing
xDo not use with damaged cord or plug. If applianc
e is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water, return to service center for inspection and repair.
xDo not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run this TRS-17 over cord. Keep cord away from heated surfaces.
xDo not unplug by pulling cord. To unplug, grasp the plug, not the cord.
xDo not handle plug or appliance with wet hands.
xThis equipment should be stored indoors and not exposed to rain.

Page 10
Parts and Instruction Manual - TRS17 Total Recovery System
MACHINE OVERVIEW
1. Handle- Used to maneuver and position the TRS-17. Contains switch box (For switchbox, see
#17)
2. Recovery tank & lid- Lid allows access to recovery tank and creates a seal to ensure suction.
Recovery tank collects waste water.
3. Solution tank & lid- Lid allows access to the solution tank and prevents external contamination of
solution tank. Solution tank holds clean water or solution.
4. Accessory racks for hoses, cords, tools etc.- Two large racks on one side and three small racks
other side of the machine. 5 total.
5. Wand storage bracket and velcro strap- Allows the operator to secure a wand attachment to the
machine for ease of transport.
6. Non-marking front 4” locking casters and rear 10” wheels.
7. Recovery/vacuum hose inlet barb- connect your recovery vacuum hose to this barb
8. Feed hose line for chemical with threaded bottle cap- secures the feed hose line to the chemical
bottle
9. Bottle holder for chemical feed system- Holds up to a one gallon chemical bottle
10.N/A for 220v
11.Chemical dispensing valve- Select between “SOAP” and “RINSE” by turning to left or right as
marked
12.Male twist lock pigtail- Connects to 50 ft cord
13.Exhaust port hose barb- Used to connect to hose with blower attachment.
14.Pressure regulator- Decrease pressure by turning counter-clockwise or increase pressure by
turning clockwise
15.Priming/Pressure relief valve- Prime system in the event of air lock. Relieves pressure in the
event of pressure lock
16.Solution line Q.D.- Pressurized connection for solution line
17.Recovery tank dump hose
18.Switch box- one switch marked “PUMP” and one switch marked “VACUUM”. Switches light up
when powered on.

Page 11
Parts and Instruction Manual - TRS17 Total Recovery System

Page 12
Parts and Instruction Manual - TRS17 Total Recovery System
OPERATION
Page 14
Parts and Instruction Manual - TRS17 Total Recovery System
OPERATION
Assembling the accessory racks:
5IF534JTTIJQQFEXJUIUIFBDDFTTPSZSBDLTBOEIBSEXBSFJOUIFTPMVUJPOUBOL8IFOZPVSFDFJWF
ZPVS534JUJTOFDFTTBSZUPTFDVSFUIFSBDLTUPUIFCPEZ5IF POMZUPPMSFRVJSFEUPDPNQMFUFUIF
BTTFNCMZJTB1IJMMJQT IFBETDSFXESJWFS
-PDBUFUIFQSFJOTUBMMFEUISFBEFEJOTFSUTPOUIFTJEFTPGUIFNBDIJOFT5IFWBDVVNIPTFSBDLTBSF
JOTUBMMFEPOUIFMFGUPGUIFNBDIJOFMFGUXIFOTUBOEJOHCFIJOEUIFNBDIJOF5IFUISFFTNBMMFSSBDLTBSF
JOTUBMMFEPOUIFSJHIUTJEFPGUIFNBDIJOF
Page 14
Parts and Instruction Manual - TRS17 Total Recovery System
OPERATION
Assembling the accessory racks:
5IF534JTTIJQQFEXJUIUIFBDDFTTPSZSBDLTBOEIBSEXBSFJOUIFTPMVUJPOUBOL8IFOZPVSFDFJWF
ZPVS534JUJTOFDFTTBSZUPTFDVSFUIFSBDLTUPUIFCPEZ5IF POMZUPPMSFRVJSFEUPDPNQMFUFUIF
BTTFNCMZJTB1IJMMJQT IFBETDSFXESJWFS
-PDBUFUIFQSFJOTUBMMFEUISFBEFEJOTFSUTPOUIFTJEFTPGUIFNBDIJOFT5IFWBDVVNIPTFSBDLTBSF
JOTUBMMFEPOUIFMFGUPGUIFNBDIJOFMFGUXIFOTUBOEJOHCFIJOEUIFNBDIJOF5IFUISFFTNBMMFSSBDLTBSF
JOTUBMMFEPOUIFSJHIUTJEFPGUIFNBDIJOF

Page 13
Parts and Instruction Manual - TRS17 Total Recovery System
Page 15
Parts and Instruction Manual - TRS17 Total Recovery System
*OTUBMMJOHNFUFSJOHUJQTGPSUIF$IFNJDBMGFFEsystem:
Remove the semi-clear hose from the bottle cap (#8 on page ). Select the appropriate metering tip
for the dilution required and  it into the tube on the bottle cap.
0QFOJOHUIFNBDIJOF







Page 14
Parts and Instruction Manual - TRS17 Total Recovery System
Page 16
Parts and Instruction Manual - TRS17 Total Recovery System
Recovering liquid from hard surfaces:
The TRS-17 is equipped with two dedicated tools for liquid recovery: The squeegee/brush wand and the
Gulper tool.
 Connect recovery vacuum hose to the recovery inlet barb (#7 on page ).
 Place the vacuum switch (see #18 on page ) into the “ON” position.
 Using either the squeegee/brush wand or the Gulper tool, to extract the liquid from the surface.
(seepage ).
 Monitor the levels in the recovery tank and empty as necessary. Use defoamer to ensure your vacuum
motor does not take in foam/fluid.
Using the blower feature:
To use, this feature connect the Blower hose (#5 on page ) to #13
on page  and turn on the vacuum motor.
Convenient for:
tBlowing fluid off countertops and walls onto the floor
tDrying faucets and other fixtures
tBlowing off dust
NOTE: Do not leave the blower hose on during normal extraction as it will reduce suction.
Chemical feed system and hard surface cleaning:
The chemical feed system is designed to deliver accurate chemical dilution for touchless surface
cleaning.
To clean hard surfaces:
 Fill the solution tank of your TRS-17 with sufficient water for the task at hand.
 Connect solution hose and accessory pressure gun.
 Select the appropriate tip and install on the cap of the chemical feed (#8 on page 1).
 Place a bottle into bottle holder (#9 on page 1).
 Take the feed tube attached to the cap (#8 on page 1) and place it inside the bottle.
 Take the cap from #8 on page  and thread it onto the bottle of chemical to secure it in
place.
 Turn the chemical dispensing valve (#11 on page 1) to the left toward the word “SOAP”.
 Chemical will only draw accurately in the “LOW” pressure setting of your pressure gun. To
activate the “LOW” pressure setting, pop the collar of the gun out.
 In “LOW” pressure, apply chemical to the walls and fixtures starting from the lowest point
tothe highest.
 Spray the floor as you make your way out of the room.
 Allow the chemical to dwell according to the chemical manufacturers recommendations.
 You may use the brush on your squeegee/brush wand to agitate particularly soiled areas.
 When you are ready to rinse away the chemical, simply turn the chemical dispensing valve
(#11 on page 1) to the word “RINSE”.
 Set your pressure gun to the desired rinsing pressure by pulling the collar in or out. Rinse
surfaces starting from the top down.
 See “Recovering liquid” for final steps.

Page 15
Parts and Instruction Manual - TRS17 Total Recovery System
NOTES

Page 16
Parts and Instruction Manual - TRS17 Total Recovery System
40 1
53
49
8
31 13 36
9
30 35 41
51
47
48
25 22
14 32
43
6 2
23 21
5
52
50
27
19
4
7
29 42
55
10
15
56
16
11
20
33
44
38
21
2
11
24 17
27
11
37
18
26
17
24
34
54
46
39
28 12
45
TRS17-220
UPPER
9/6/2017
UPPER ASSEMBLY

Page 17
Parts and Instruction Manual - TRS17 Total Recovery System
UPPER ASSEMBLY BOM (page 1)
Page 19
Parts and Instruction Manual - TRS17 Total Recovery System
UPPER ASSEMBLY BOM
BILL OF MATERIAL
ITEM PART # QTY DESCRIPTION
110989-2A 1 BALL FLOAT
2 A00052 4 90 DEGREE ELBOW, .25" MP X .25" FP
3 A00060 1 BARB, .375" X .25" MPT, BRASS
4 A00124 2 LOCKNUT, .25NPT, BRASS
5 A00139 1 BARB, .25 X .25MP, BRASS
6 A13881 1 CHECK VALVE
7 A90004 1 BARB, .5 X .25MP, BRASS
8 B010314 1 WIRE HARNESS
9 B02211-1 2 ROCKER SWITCH
10 C00234 1 WASHER, FENDER, .25" ID, SS
11 C00238 7 1/4" ID SEALING WASHER
12 C00262 1 HEX NUT, 5/16-18, ZP
13 C00295-1 2 #10 X 3/4" SHEET METAL SCREW, SS
14 C00313 4 1/4-20 X .75" HEX BOLT
15 C00316 1 SCREW, 1/4-20 X 3/4, PH, SS
16 C02251 1 JAM NUT, 1/4-20, SS
17 C02282 4 HEX BOLT, 1/4-20 X 1 1/2"
18 C02294 6 SCREW, 1/4-20 X 1 1/4, SS
19 C11144 2 SCREW, 1/4-20 X 2" SS
20 C11167 2 1/4-20 X 3/4" SCREW, SS
21 C11244 3 WASHER, 9/16" ID X 1.5" OD
22 C11540 2 WASHER, 5/16"
23 C12021 1 WASHER, FLAT, 9/16 ID, SS
24 C12039 4 FENDER WASHER, 1/4" ID, 1" OD
25 C12110 2 HEX BOLT, 3/8-16 X 1 3/4
26 C13361 2 SCREW, 1/4-20 X 1 1/2, TRUSS, SS
27 C14017 8 SCREW, 10-32 X 1/2", TRUSS
28 C14067 1 HEX SCREW, 5/16-18 X 1 1/4", SS

Page 18
Parts and Instruction Manual - TRS17 Total Recovery System
UPPER ASSEMBLY BOM (page 2)
Page 20
Parts and Instruction Manual - TRS17 Total Recovery System
UPPER ASSEMBLY BOM (page 2)
BILL OF MATERIAL
ITEM PART # QTY DESCRIPTION
29 D00373 2 FILTER, INLET
30 D010284 1 SWITCHPLATE
31 D03421 1 COVER, SWITCHPLATE, 2 SWITCH
32 D13683 1 CHEMICAL BOTTLE HOLDER
33 D13697-2 2 HOSE RACK
34 D13698-2 2 RACK, SOLUTION HOSE/POWER CORD
35 E010453 1 GASKET, SWITCH BRACKET
36 E03433 1 GASKET, SWITCH BRACKET
37 E11128 2 DRAIN VALVE GASKET
38 E11836 1 GASKET, RECOVERY TANK, LID
39 E14058 1 SHRINK TUBING, 2.5" ID X 2.0" L
40 F11785-1-MM 1 LID, RECOVERY TANK
41 F11786-1-MM 1 HANDLE
42 F11787-1-MM 1 SOLUTION TANK
43 F11788-1-MM 1 RECOVERY TANK
44 F11791-1-MM 1 LID, SOLUTION TANK
45 H13699 1 DECAL, MINUTEMAN, WHITE
46 J00650 1 SCREW CLAMP #24 1.25 INCH
47 K00665-1 2 1.5" HOSE ADAPTER
48 K00666 1 1-1/2" 90 DEGREE ELBOW
49 K00672 1 PVC PIPE, 1.5" SCH40, 1.3125'
50 K00672-1 1 PVC PIPE, 1 1/2" X 2.25", SCH40
51 K00741 1 ADAPTER, MALE, 1 1/2", SCH40
52 K11185 1 90 DEGREE ELBOW, SCH40, MPT, SF
53 K11965 1 RETURN BEND, 1 1/2"
54 K13724 1 DRAIN HOSE ASSEMBLY
55 S11179 1 NON-SKID TAPE
56 S13706-A 1 STRAP, WAND, VELCRO

Page 19
Parts and Instruction Manual - TRS17 Total Recovery System
LOWER ASSEMBLY
2
17
58 20
78 80
413
42 12
65 14
911
8
10
15
71 21 23 32
34
6
50
69
18 81
39 72
29
27
26
83
28
55
66
84
16
40
70
38
60
51
5
49
7
3
75
41 30
77
63
35
59
61
33
82
57
48
25
68 43 44
64
19
79
22
36
47
24
1
31 73
76
62
30
32 30
34
77
74
37 52
32
TRS17-220 BASE 9/6/2017
46 53
73
70
13
4
56 54

Page 20
Parts and Instruction Manual - TRS17 Total Recovery System
LOWER ASSEMBLY BOM (page 1)
Page 22
Parts and Instruction Manual - TRS17 Total Recovery System
LOWER ASSEMBLY BOM (page 1)
BILL OF MATERIAL
ITEM PART # QTY DESCRIPTION
1 -- 2 HOSE ASSEMBLY
J00580 1 HIGH PRESSURE/TEMP HOSE .25" ID X 10"
L
J00660 2 SWAGE FITTING, .25" FP
2 -- 1 HOSE ASSEMBLY, .25" MP X .25" FP, 10" L
J00580 1 HIGH PRESSURE/TEMP HOSE .25" ID X 10"
L
J00659 1 SWAGE FITTING, .25" MP
J00660 1 SWAGE FITTING, .25" FP
3 -- 1 HOSE ASSEMBLY, .25" MP X .25" MP, 35" L
J00580 1 HIGH PRESSURE/TEMP HOSE .25" X 35"
J12932 2 CRIMP, .25" X .25" MPT, SWIVEL
4 A00052 2 90 DEGREE ELBOW, .25" MP X .25" FP
5 A00053 1 45 DEGREE ELBOW, .25" MP X .25" FP
6 A00055 3 NIPPLE, .125", CLOSE, BRASS
7 A00060 1 BARB, .375" X .25" MPT, BRASS
8 A00073 2 90 DEGREE ELBOW, BRASS
9 A00094C 1 BODY, CHECK VALVE, .25" M
10 A00094E 1 CHECK VALVE
11 A00097A 1 CAP, INLINE FILTER
12 A00104 1 QD, .25" M X .25" FP, BRASS
13 A00114B 4 HEX NIPPLE, .25" MP X .125" MP
14 A00134 1 90 DEGREE ELBOW, .25" BARB X .125" MPT
15 A00135 1 TEE, .125" FP X .125" FP X .125" MP
16 A00155 1 PLUG, MALE, .25"
17 A00161 1 TEE, .25" FP X .25" FP X .25" FP
18 A00168-18 1 BUSHING, .25" M X .125" F
19 A12917 2 ELBOW, .25" F X .375" M, NPT
20 A12960 2 NIPPLE, HEX, .25" X .25", BRASS
21 A12964 1 COUPLER, .25", BRASS
22 A13430 1 BARB, ELBOW, .375" MP X .5" BARB
23 A13688 1 BALL VALVE, 3-WAY, .125"
24 B00192 2 TIE HOLDER, W/ ADHESIVE