Mira Platinum User manual

1
Mira Platinum Wireless Controller
User Guide

2
3
Contents
Introduction......................................................................... 4
Safety Information.............................................................. 5
Control layout..................................................................... 6
Display symbols................................................................. 7
Using the Shower............................................................... 8
Switch on/off................................................................... 8
Adjust Temperature.......................................................... 10
Adjust Flow........................................................................11
Functions .......................................................................... 12
Function Menu.................................................................. 14
Enter the Function Menu.............................................. 14
Exit the Function Menu ................................................ 15
Changing Functions/Settings.......................................... 16
Maximum showering water temperature...................... 16
Eco............................................................................... 17
Warm-Up...................................................................... 18
Clock Setting................................................................ 19
Clock Display ............................................................... 21
Calibration No. ............................................................. 23

3
Flow Range.................................................................. 24
Control Frequency........................................................ 26
Replacing the Batteries.................................................... 27
Fault Diagnosis................................................................. 28
Error Codes.................................................................. 28
Error During Function Change..................................... 29
General Faults.............................................................. 30
Cleaning ............................................................................ 32
Disposal and Recycling................................................... 32
Guarantee of Quality........................................................ 34
What to do if something goes wrong ............................. 35
Service Repairs................................................................. 35
To Contact Us ......................................................back page

4
5
Introduction
Thank you for purchasing a quality Mira product. To enjoy the full potential
of your new product, please take the time to read this guide thoroughly and
keep it handy for future reference.
TheMiraPlatinumWirelessControllerisaremoteuserinterfaceandcontrols
the following functions:
Showering Water Temperature• Showering Water Flow• Maximum Showering Water Temperature• Eco Mode• Warm-Up Mode• Clock• Flow Range•
This guide covers the setting and use of these functions and includes a
trouble shooting guide should the appliance not function as expected.
For issues relating to the installation of the appliance or other associated
products, please refer to the relevant Installation Guide(s) or contact our
Customer Services Team. (Details in the back of this guide.)
NOTE! ALL FUNCTIONS ARE ONLY AVAILABLE AFTER THE
CONTROLLER HAS BEENASSIGNED TOAMIRAPLATINUM DIGITAL
MIXER VALVE. (See Mira Platinum Installation Guide.)

5
Safety Information
1. Make sure that you fully understand how to operate this shower
and make sure that it is properly maintained in accordance with the
instructions given in this manual.
2. Sunburn or skin conditions can increase your sensitivity to hot water.
Make sure that you set the shower to a cooler temperature.

6
7
Control Layout Turn Outer Ring
Showering Water Flow Adjustment
Decrease
Flow Increase Flow
Increase
Temperature
Decrease
Temperature
Display Start/Stop

7
Display Symbols
Flow Display
Low Battery
Display
Control Out
Of Range
Temperature Display
Clock Display
Economy Flow
Display

8
9
Using the Shower
Switch on/off
Press “ ” to start or stop shower.
Temperatureandowsettingswillbesameaswhenlastused.
After a short period, display will dim to help extend battery life.
Approximately 10 minutes after shower has stopped, display will turn
off automatically.
Shower will not run continuously for more than 30 minutes before
stopping automatically (5 minutes when “ECO” function is set to
“on”).
When “Warm-Up” function is “on”, there will be a short delay (5
seconds)beforewaterowsfromshower.

9

10
11
Adjust Temperature
While shower is running, press “ + ” or “ - ” to adjust temperature.
Showering temperature appears on display in degrees Celsius (°C).

11
Adjust Flow
Turnouterringclockwiseoranticlockwisetoadjustow.Showering
owlevelappearsondisplayinwhitebars.

12
13
Functions
Thefollowingfunctionscanbe alteredindividuallytoadjusthow theshower
operates:
F1 - Maximum Showering Water Temperature. This is the temperature
the shower cannot go beyond when in use.
F2 - Eco. The shower will stop
automatically after 5 minutes. When
thissettingis“on”,maximumavailable
showering flow is limited to half
the ow normally produced. “ECO”
symbol is displayed. When setting
is “off”, maximum showering flow
will be at full flow. “ECO” symbol
goes out when more than half ow
is selected.
F3 - Warm-Up. When this setting is
“on” and the shower is started, there
is a short delay (5 seconds) before
waterowsandtemperaturedisplay
willashtoindicateshoweriswaiting
forselecteddisplaytemperaturetobe
achieved.Whenshowerstops,temperaturehas been reached and shower
is ready for use, press “ ” as normal. If temperature cannot be found,
shower will stop automatically after 5 minutes.

13
When “Warm-Up” setting is “off”,temperaturedisplaywillnotashand
shower operates as normal.
Note! Whenusedwithsomecombinationboilers,thewarm-upfunctionmay
be impaired. This is due to the functional nature of combination boilers.
F4 - Clock Setting. To set the time.
F5 - Clock Display. When Clock
Display is “on”, time is displayed
whenshowerhasstopped,orafter10
secondsofinactivitywhilsttheshower
is running. When Clock Display is
“off”, the time is replaced by the
showering temperature.
F6 - Calibration Number.
F7 - Flow Range. For use with High Pressure/Combi Valve version only.
Thewaterowrate(showeringforce)canbeadjustedtowithinadesired
rangeby settinga low pointand a highpoint.Duringadjustmenttheshower
will need to be started.
F8 - Control Frequency. An unreliable functioning of the appliance (not
always able to change settings of shower) may indicate radio interference
by another device transmitting locally on same channel. Changing channel
may resolve this problem.
offon

14
15
Function Menu
Enter the Function Menu
Press “+” and “ ” buttons
simultaneously until “End” is
displayed on the unit.
Use “+” or “-” buttons to cycle
through functions and press
“ ” to enter setting.
(See following sections in this
guidefordetailsoneachfunction
and how to alter their settings.)
Note! Ifsignallossoccursduring
a function change, “Err” will
appear on display.
Press “ ” to clear and retry
function change.

15
Exit the Function Menu
When finished, use “+” or “-”
buttons to cycle back through
functions until “End” appears.
Press “ ” to exit.
Control is ready to use.
If necessary, test shower to
see if functions are working as
expected.

16
17
Changing Functions/Settings
Maximum Showering Water Temperature
Press “+” or “-” to adjust
temperature.
Maximum = 48°C
Minimum = 35°C
Cycle menu to “F 1” and press
“ ”.
Factory default “45°C”.
Press “ ” to set.
Press“ ” to exit back to Function
Menu. See section “Exit the
Function Menu”.

17
Eco
Press “+” or “-” to change setting
“on” or “off”.
Cycle menu to “F 2” and press
“ ”.
Factory default “off”.
Press “ ” to set.
Press“ ” to exit back to Function
Menu. See section “Exit the
Function Menu”.

18
19
Warm-Up
Press “+” or “-” to change setting
“on” or “off”.
Cycle menu to “F 3” and press
“ ”.
Factory default “off”.
Note! Function will not work with combination boilers.
Press “ ” to set.
Press“ ” to exit back to Function
Menu. See section “Exit the
Function Menu”.

19
Clock Setting
Press “-” to change hour
setting.
Press “+” to change minute
setting.
Cycle menu to “F 4” and press
“ ”.
Factory default “10:43”.
Note! Can also be activated by disconnecting and reconnecting battery.

20
21
Press “ ” to set time and exit
back to Function Menu. See
section “Exit the Function
Menu”.