MIRADOR 88S User manual

BIOCLIMATIC
PERGOLA
INSTRUCTION MANUAL
4 PILLARS
88S

1
This manual will provide you with clear and detailed instructions on how to safely and correctly assemble and maintain your pergola, to ensure it
brings you many years of use and enjoyment.
IMPORTANT
Warning: Important safety instructions. It is important for the safety of persons to follow these instructions. Please keep these instructions in a safe
place.
This pergola can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack
of experience and knowledge if they have been given supervision or instruction concerning use of the pergola in a safe way and understand
the hazards involved. Children shall not play with the pergola. Cleaning and user maintenance shall not be made by children without supervison.
Intended use
This pergola is intended for outdoor domestic use in residential environments, and to protect users from direct sunlight, glare and heat.
Any use or modication to the pergola not included in this manual shall be considered as improper use, which may cause considerable danger
to users and property and will void the product warranty.
THANK YOU
FOR PURCHASING
OUR MIRADOR®
BIOCLIMATIC PERGOLA!
Mirador_88S_4_Pillar_EN_23v1.0

2
- Before Assembling Your Pergola
- Important Safety Advice
- List of Parts
- Installation
- Operating Your Pergola
- Problem Solving, Care & Maintenance
- Warranty & Complaints Procedure
- Disassembly and Disposal of the Product
- Certication Information
3
5
7
10
26
27
29
30
31
TABLE OF CONTENTS

3
BEFORE ASSEMBLING
YOUR PERGOLA
Make sure you have all the tools required for assembling your pergola
In order to assemble your pergola safely and correctly, please ensure you have access to the following tools and accessories, all of which are not
provided.
Please read all the instructions carefully before you begin, and follow the steps in the
order they are presented.
Hard hat Protective gloves Box cutter Tape measure Spirit level Phillips screwdriver
Cordless screwdriver Hexagonal spanner/
wrench set
Hammer drill Hammer 2 step ladders Scissors

4
Check to ensure there are no missing parts
Before you begin installation, please check that you have all the parts required to assemble your pergola. Please also carefully check that the
quantity of parts match with that of the model you have purchased.
If any parts are missing, please contact customer service before beginning the installation .
Prepare the parts you will need for each step
In the Installation section of the manual, each step indicates the necessary parts and quantities required to complete the step. We recommend that
you prepare the parts you will need for each installation step. Doing this will save you time and eort during assembly. If possible, place the parts on
cardboard or other soft surface to protect from scratching the painted surfaces.
Select a suitable location:
Warning:
Most terraces or patios are designed with a slight slope to prevent (rain) water from forming pools or reaching the house or other structures.
For the perfect pergola installation, a level surface without such a slope is required. Small pebbles could also prevent the pergola from being
safely secured on the ground.
If the pergola is installed on an uneven surface, it may prevent accessory components from working correctly and may void the product
warranty. Additional adjustment of the pillar heights would also be necessary.
Prepare a foundation:
To prepare it, you need to:
- check for underground pipes and cables (Call 811 before you dig if you live in the USA)
- check with your local authorities regarding any building permits that may be required
- contact a reliable contractor if you decide to have a concrete base
The ground should be solid
and at The ground should be level Sucient water drainage Easy access to power No overhanging trees and powerlines
>2.5°

5
IMPORTANT
SAFETY ADVICE
For the safety of all persons installing and using the pergola, it is important to follow
the safety guidelines below.
The pergola must be
positioned and xed on at
level surface.
Always wear appropriate
work shoes, gloves and eye
protection when working.
Work well away from power
lines, particularly when
handling metal parts.
If using power tools or
a ladder, always follow
the manufacturer’s safety
instructions.
Make sure the pergola
complies with local building
regulatory codes.
Working at heights can be
dangerous. Always wear
protective clothing to prevent
injury in the event of a fall.
Only use ladders and
scaolding with a suciently
high load bearing capacity
Keep clothing and body parts
away from the pergola to
prevent them from getting
caught in the moving parts
Foliage or other foreign
objects on the roof and in the
guide rails should be removed
regularly, to prevent damage
to the pergola.
Only use replacement parts
that are approved by the
manufacturer.
Approved

6
Prior to each operation, visually
check the pergola for damage.
If damage is visible, stop using
it immediately and contact
authorized personnel to repair
the damage.
Do not touch moving parts
during operation.
Do not place anything on the
roof
Changes to the design or
conguration of equipment
may not be made without
consulting the manufacturer
or authorized representative.
Dispose of all plastic bags
safely. Keep them out of the
reach of children.
Keep children and pets away
from the assembly area until
the work is completed.
Do not attempt to assemble
the pergola in windy or wet
conditions.
Hanging objects on the
pergola may cause serious
damage and is not permitted
Do not climb on the roof
Put the louvers into the
vertical position during
snowfall or wind to avoid
damage.
Installation of non-Mirador
branded accessories will void
the product warranty and
can damage the operating
mechanism
After prolonged use we
recommend you check all
the ttings are tightened
securely
Please recycle packaging
where possible.
Do not attempt to assemble
the product if you are tired, or
after consuming alcohol
Mirador®

7
Please carefully check that the quantity of parts matches with that of the model you have purchased.
PLEASE NOTE that the anchor bolts provided may not be suitable for your chosen installation location.
Please check before proceeding.
DO NOT USE AN IMPACT CORDLESS SCREW DRIVER TO ASSEMBLE THE PERGOLA. USE A STANDARD
CORDLESS SCREW DRIVER ON THE BASE SETTING. ALL HOLES HAVE BEEN PREDRILLED OR FITTED FOR
ASSEMBLY
REF Part Name
Length
3m/10ft. 3.6m/12ft.
ACorner Pillar 4 pcs 4 pcs
B1 Side beam with gearbox 1 pcs 1 pcs
B2 Side beam without gearbox 1 pcs 1 pcs
CEnd beam 2 pcs 2 pcs
HCrank 1 pcs 1 pcs
IFoot plate cover 4 pcs 4 pcs
JFoot plate 4 pcs 4 pcs
MShaft support cover 38+2 pcs 46+2 pcs
LIST OF PARTS
Width
Length

8
REF Part Name 3m/10ft. 3.6m/12ft.
NCorner pillar cover 4 pcs 4 pcs
OScrew ST5.65x45mm 24+2 pcs 24+2 pcs
PScrew M5x12mm 76+4 pcs 92+5 pcs
QScrew 4.2x25mm 76+4 pcs 92+5 pcs
RScrew 5.5x19mm 12+2 pcs 12+2 pcs
VCrank coupler 1 pcs 1 pcs
WAnchor bolt M8x80mm 16 pcs 16 pcs
XHex key (small) 1 pcs 1 pcs
YHex key (large) 2 pcs 2 pcs
Z12mm SDS Plus Drill Bit 1 pcs 1 pcs
Z10 Spare plastic pin 0+10 pcs 0+10 pcs
CONNECTING STRIP VARIATIONS

9
REF Part Name 3m/10ft. 3.6m/12ft.
DLouver 19 pcs 23 pcs
KLouver end cap 37+2 pcs 45+2 pcs
LLouver end cap
with control arm 1 pcs 1 pcs
GConnecting strip 2 pcs 2 pcs
SCotter pin 38+6 pcs 46+7 pcs

10
1A
Slide the foot plate cover Iwith its
wide opening facing outwards on the
straight end of the corner pillar A.
1B
Push the foot plate Jagainst the
straight end of the corner pillar A.
It only ts in one direction and in one
position. If in doubt, rotate it until it ts
easily.
Screw in the foot plate Jwith 6 screws
Ousing a cordless screwdriver
1. Set up the corner pillars A
INSTALLATION
Installation Video
4 PERSONNEL REQUIRED
A
x 6O
J
Ix 4
Ax 4
Ax 4
Jx 4 Ox 24
A
I
x 4
x 4

11
2. Connect the side beam with gearbox B1
to the corner pillars A
2A
Using a hex key (large) Y, slightly
loosen the 8 built-in screws at both ends
of the side beam with gearbox B1 .(4 on
each side)
2B
Lay two corner pillars Aand place the
side beam with gearbox B1 on the oor,
as shown in the picture.
Yx 1
B1 x 1
B1
A
Ax 2
2C
Slide the side beam with gearbox B1 into
the grooves of the corner pillars A, in
such a way that the slot nuts of the side
beam interlock with those of the corner
pillars.

12
2D
Tighten the screw with the hex key Y.
3A
Repeat steps 2A - 2D to connect the
beam without gearbox B2 with the
remaining two corner pillars A.
3. Connect the side beam without gearbox B2
to the remaining two regular corner pillars A
Yx 1
B2 x 1
Ax 2
A
B2

13
4. Slide in the two end beams C
This phase requires four persons and at least two stepladders.
Make sure that the stepladders are standing securely to avoid falling.
Only use ladders suitable for this kind of installation work.
4A
Stand the two structures built during
steps 2 and 3 in an upright position, and
place them at one end beam length
away from one another. Make sure that
one person is supporting each corner
leg Ato prevent the structures from
falling
4B
Slightly loosen the 8 built-in screws at
both ends of the end beam C.
Yx 1
Cx 1
4 PERSONNEL REQUIRED
one end beam
length
one end beam
length

14
4C
Slide the slot nuts of the end beams C
from above into the slots of the corner
pillars A
4D
Once the beam is in the correct position,
tighten the 8 built-in screws on both
ends using the hex key Yprovided
4E
Install the other end beam Cby
following steps 4B - 4D
Cx 1
Yx 1
Cx 1
Yx 1
C
AA
C
A
A

15
5. Check the alignment of the frame and
the distance between the corner pillars
You are now almost done installing the main frame of the pergola. Please double check
to ensure all beams and pillars have been installed and tted correctly. You may have to
unscrew certain bolts during this step.
You will also need a tape measure and a spirit level to complete this step.
5A
Choose one of the corner pillars A
and work from this pillar. Choose this
pillar carefully as it will dene the nal
installation location of the pergola.
Use a spirit level to
measure against both of the inner sides
to ensure that the corner pillar is straight
and level.
Make sure this corner pillar does not
move position during the remaining
installation steps.
5B
Measure the distances between the
adjacent corner pillars. Adjust accordingly
and ensure the distances match those
shown in the opposite gure.
Spirit level
a
a
b
b
Size a b
(m/ft) (mm) (inch) (mm) (inch)
3x3/10x10 2806.2 110.5 2795.8 110.1
3x3.6/10x12 3415.4 134.5 2795.8 110.1

16
5C
Measure the diagonal distance between
the opposite corner pillars. Adjust the
other corner pillars accordingly until
both diagonal distances are equal.
You may have to repeat the above steps
after completing the remaining steps.
5D
Check that all corner pillars are straight
and level using a spirit level. If the corner
pillars or beams are still not level, this
means that your main building surface
isn’t suciently level, and that you will
need to raise the corner pillars that
are positioned lower than the others.
(Contact qualied workers if needed.)
Warning:
If you do not adjust the main structure
at this point, you may encounter
problems when tting the roof deck and/
or accessories to the frame.
Spirit level
C
C
Size c
(m/ft) (mm) (inch)
3x3/10x10 3966.2 156.1
3x3.6/10x12 4418.7 173.9

17
6. Install Crank H
6A
Locate the gearbox on the side beam
with gearbox B1
6B
Unscrew and remove the small screw
from the crank connector.
Insert the crank coupler into the crank
connector and re-insert and tighten the
small screw.
Vx 1
B1
V
B1
Gearbox

18
6C
Insert the end of the crank Hinto the
crank coupler V, and turn until the
crank locks rmly in place
Hx 1
H
V

19
7A
Prepare the driving louver: select one of
the louvers Dto be the driving louver.
Attach the louver end cap with control
arm Lto one end of the driving louver,
and attach an louver end cap Kto the
other end of the driving louver. Use two
screws Q on each side, and x them
rmly using a cordless screwdriver.
7. Install the louvers, and connecting strips
Lx 1
Kx 1 Qx 4
Dx 1
L
D
Q
K
D
Q
7B
Prepare the regular louvers: attach the
louver end caps Kto each end of the
rest of the louvers Dwith two screws
Qusing a cordless screwdriver.
Repeat this step for all louvers.
Part \ Length 3m/10ft. 3.6m/12ft.
72 88
36 44
18 22
D
K
Q
K
D
Q
K
Q
D