MIRADOR BIOCLIMATIC PERGOLA 111 User manual

B IOC L I M ATI C
PE RGOL A 111
I N STR U CTI O N M A N UA L
6 P I L L A R S

1
This manual will provide you with clear and detailed instructions on how to safely and correctly assemble and maintain your pergola, to ensure it
brings you many years of use and enjoyment.
IMPORTANT
Warning: Important safety instructions. It is important for the safety of persons to follow these instructions. Please keep these instructions in a safe
place.
This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack
of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand
the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be made by children without supervison.
Intended use
This pergola is intended for outdoor domestic use in residential environments, and to protect users from direct sunlight, glare and heat.Any use or
modication to the pergola not included in this manual shall be considered as improper use, which may cause considerable danger
to users and property and will void the product warranty.
For parts and customer service, please call [phone] in the U.S. and Canada (English and Spanish)Monday – Friday, 6:30 am to 4:30 pm,
Pacic Time. Or email: [e-mail]
Digital instruction manual is also available on our ocial website www.miradoroutdoor.com for your reference.
THIS INSTRUCTION MANUAL IS FOR THE FOLLOWING MODELS:
THANK YOU
FOR PURCHASING
OUR MIRADOR
BIOCLIMATIC PERGOLA!
Mirador_111_Bioclimatic Pergola_6_Pillars_EN_23v1.0
Series \ Louver
Single aluminum Single Steel Double aluminum
111 111 Premium 111 Classic 111 Deluxe
111 A 111 S 111 DA

2
- Before Assembling Your Pergola
- Important Safety Advice
- List of Parts
- Installation
- Operating Your Pergola
- Problem Solving, Care & Maintenance
- Warranty & Complaints Procedure
- Disassembly and Disposal of the Product
- Certication Information
3
5
7
11
32
33
35
36
37
TABLE OF CONTENTS

3
BEFORE ASSEMBLING
YOUR PERGOLA
Make sure you have all the tools required for assembling your pergola:
In order to assemble your pergola safely and correctly, please ensure you have access to the following tools and accessories, all of which are not
provided.
Hard hat Protective gloves Box cutter Tape measure Spirit level Phillips screwdriver
Cordless screwdriver Hexagonal spanner/
wrench set
Hammer drill Hammer 2 step ladders Scissors
WARNING: Improtant safety instructions. Follow all instructions, since incorrect
installation can lead to severe injury.

4
Check to ensure there are no missing parts
Before you begin installation, please check that you have all the parts required to assemble your pergola. Please also carefully check that the
quantity of parts match with that of the model you have purchased.
If any parts are missing, please refer Warranty & Complaints Procedure to contact customer service before beginning the installation.
Prepare the parts you will need for each step
In the Installation section of the manual, each step indicates the necessary parts and quantities required to complete the step. We recommend that
you prepare the parts you will need for each installation step. Doing this will save you time and eort during assembly. If possible, place the parts on
cardboard or other soft surface to protect from scratching the painted surfaces.
Select a suitable location:
The ground should be solid
and at The ground should be level Sucient water drainage Easy access to power No overhanging trees and powerlines
>2.5°
Check to ensure there are no missing parts:
Before you begin installation, please check that you have all the parts required to assemble your pergola. Please also carefully check that the
quantity of parts match with that of the model you have purchased.
If any parts are missing, please refer Warranty & Complaints Procedure to contact customer service before beginning the installation.
Prepare the parts you will need for each step:
In the Installation section of the manual, each step indicates the necessary parts and quantities required to complete the step. We recommend that
you prepare the parts you will need for each installation step. Doing this will save you time and eort during assembly. If possible, place the parts on
cardboard or other soft surface to protect from scratching the painted surfaces.
Select a suitable location:
Warning:
Most terraces or patios are designed with a slight slope to prevent (rain) water from forming pools or reaching the house or other structures.
For the perfect pergola installation, a level concrete surface without such a slope is required. Small pebbles could also prevent the pergola from
being safely secured on the ground.
If the pergola is installed on an uneven surface, it may prevent accessory components from working correctly and may void the product warranty.
Prepare a foundation:
To prepare it, you need to:
- check for underground pipes and cables (Call 811 before you dig if you live in the USA)
- check with your local authorities regarding any building permits that may be required
- contact a reliable contractor to have concrete base if you dont have one
Do not assemble the pergola on sandy, muddy or loose soil, as the stakes do not have the sucient anchorage to be installed in these types of soil.
The ground should be solid
and at The ground should be level Sucient water drainage Easy access to power No overhanging trees and powerlines
>2.5°

5
IMPORTANT
SAFETY ADVICE
For the safety of all persons installing and using the pergola, it is important to follow
the safety guidelines below.
The pergola must be
positioned and xed on at
level surface.
Always wear appropriate
work shoes, gloves and eye
protection when working.
Work well away from power
lines, particularly when
handling metal parts.
If using power tools or
a ladder, always follow
the manufacturer’s safety
instructions.
Make sure the pergola
complies with local building
regulatory codes.
Working at heights can be
dangerous. Always wear
protective clothing to prevent
injury in the event of a fall.
Only use ladders and
scaolding with a suciently
high load bearing capacity.
Keep clothing and body parts
away from the pergola to
prevent them from getting
caught in the moving parts.
Foliage or other foreign
objects on the roof and in the
guide rails should be removed
regularly, to prevent damage
to the pergola.
Only use replacement parts
that are approved by the
manufacturer.
Approved

6
Do not touch moving parts
during operation.
Do not place anything on the
roof.
Hanging objects on the
pergola may cause serious
damage and is not permitted.
Changes to the design or
conguration of equipment
may not be made without
consulting the manufacturer
or authorized representative.
Changes to the design or
conguration of equipment
may not be made without
consulting the manufacturer
or authorized representative.
Dispose of all plastic bags
safely. Keep them out of the
reach of children.
Keep children and pets away
from the assembly area until
the work is completed.
Do not attempt to assemble
the pergola in windy or wet
conditions.
Do not climb on the roof.
Prior to each operation, visually
check the pergola for damage.
If damage is visible, stop using
it immediately and contact
authorized personnel to repair
the damage.
Put the louvers into the
vertical position during
snowfall or wind to avoid
damage.
Installation of non-Mirador
branded accessories will void
the product warranty and
can damage the operating
mechanism.
After prolonged use we
recommend you check all
the ttings are tightened
securely.
Please recycle packaging
where possible.
Do not attempt to assemble
the product if you are tired, or
after consuming alcohol.
Mirador®

7
Please carefully check that the quantity of parts matches with that of the model you have purchased.
PLEASE NOTE that the anchor bolts provided may not be suitable for your chosen installation location.
Please check before proceeding.
DO NOT USE AN IMPACT CORDLESS SCREW DRIVER TO ASSEMBLE THE PERGOLA. USE A STANDARD
CORDLESS SCREW DRIVER ON THE BASE SETTING. ALL HOLES HAVE BEEN PREDRILLED OR FITTED FOR
ASSEMBLY.
REF Part Name
Length
5.3m/17ft. 6m/20ft. 7.2m/24ft.
ACorner Pillar 4 pcs 4 pcs 4 pcs
A1 Middle Pillar 2 pcs 2 pcs 2 pcs
BSide beam with gearbox 1 1 pcs 1 pcs 1 pcs
B1 Side beam with gearbox 2 1 pcs 1 pcs 1 pcs
B2 Side beam without gearbox 1 1 pcs 1 pcs 1 pcs
B3 Side beam without gearbox 2 1 pcs 1 pcs 1 pcs
CEnd beam 2 pcs 2 pcs 2 pcs
HCrank 2 pcs 2 pcs 2 pcs
LIST OF PARTS
Width
Length

8
REF Part Name 5.3m/17ft. 6m/20ft. 7.2m/24ft.
IFoot plate cover 6 pcs 6 pcs 6 pcs
JFoot plate 6 pcs 6 pcs 6 pcs
MShaft support cover 68+3 pcs 76+3 pcs 92+3 pcs
NCorner pillar cover 4 pcs 4 pcs 4 pcs
N1 Middle pillar cover 2 pcs 2 pcs 2 pcs
OScrew ST5.65x45mm 36+3 pcs 36+3 pcs 36+3 pcs
PScrew M5x12mm 136+7 pcs 152+8 pcs 184+9 pcs
QScrew 4.2x25mm 136+7 pcs 152+8 pcs 184+9 pcs
RScrew 5.5x19mm 16+3 pcs 16+3 pcs 16+3 pcs
T1 Spacer sleeve 4 pcs 4 pcs 4 pcs
U1 Socket screw M8x45mm 4 pcs 4 pcs 4 pcs
VCrank coupler 2 pcs 2 pcs 2 pcs
WAnchor bolt M8x80mm 24 pcs 24 pcs 24 pcs

9
REF Part Name 5.3m/17ft. 6m/20ft. 7.2m/24ft.
XHex key (small) 1 pcs 1 pcs 1 pcs
YHex key (large) 2 pcs 2 pcs 2 pcs
Z12mm SDS Plus Drill Bit 1 pcs 1 pcs 1 pcs
Z10 Spare plastic pin 0+10 pcs 0+10 pcs 0+10 pcs
Double aluminum
REF Part Name 5.3m/17ft. 6m/20ft. 7.2m/24ft.
DLouver 34 pcs 38 pcs 46 pcs
KLouver end cap 66+3 pcs 74+3 pcs 90+3 pcs
LLouver end cap
with control arm 2 pcs 2 pcs 2 pcs
GConnecting strip 2 pcs 2 pcs 2 pcs
SCotter pin 34+5 pcs 38+6 pcs 46+7 pcs
LOUVER REALATED
VARIATIONS
The type of louver provided depends on the model of pergola you
have purchased:
Model Louver type
111 Premium / 111 A Single aluminum
111 Classic / 111 S Single steel
111 Deluxe / 111 DA Double aluminum

10
Single aluminum
REF Part Name 5.3m/17ft. 6m/20ft. 7.2m/24ft.
DLouver 34 pcs 38 pcs 46 pcs
KLouver end cap 66+3 pcs 74+3 pcs 90+3 pcs
LLouver end cap
with control arm 2 pcs 2 pcs 2 pcs
GConnecting strip 4 pcs 4 pcs 4 pcs
SCotter pin 68+10 pcs 76+11 pcs 92+14 pcs
Single Steel
REF Part Name 5.3m/17ft. 6m/20ft. 7.2m/24ft.
DLouver 34 pcs 38 pcs 46 pcs
KLouver end cap 66+3 pcs 74+3 pcs 90+3 pcs
LLouver end cap
with control arm 2 pcs 2 pcs 2 pcs
GConnecting strip 4 pcs 4 pcs 4 pcs
SCotter pin 68+10 pcs 76+11 pcs 92+14 pcs

11
1A
Slide the foot plate cover Iwith its
wide opening facing outwards on the
straight end of the pillar A& A1 .
1B
Push the foot plate Jagainst the
straight end of the pillar A& A1 .
It only ts in one direction and in one
position. If in doubt, rotate it until it ts
easily.
Screw in the foot plate Jwith 6 screws
Ousing a cordless screwdriver.
1. Set up the pillars A& A1
INSTALLATION
Installation Video
x 6O
J
Ix 6
Ax 4
A1 x 2
Jx 6 Ox 36
A&A1
A&A1
I
x 6
x 6

12
2. Connect the side beams B& B1 to the
corner pillars A
2A
Slide the end of side beam Binto the
end of side beam B1 , until the end
piece is no longer visible.
B1 x 1
Bx 1
B1
B1
B
B

13
2B
Connect the two side beams by inserting
the spacer sleeves T1 and socket screws
U1 .
2C
Using a hex key (large) Y, slightly
loosen the 8 built-in screws at the corner
ends of the side beams (4 on each side).
Then loosen the top 6 built-in screws
where the side beams meet in the middle.
Do not touch the bottom 2 screws of B1 .
T1 x 2
U1 x 2
Yx 1
Yx 1
U1
T1
B
B1

14
2E
Slide the side beams into the grooves
of the pillars Aand A1 in such a way
that the slot nuts of the side beams B
and B1 interlock with the slots in the
pillars.
2D
Align the newly connected side beams
with the corresponding pillars
Aand A1 . B
BB1
B1
A1
A
Yx 1
A1 x 1
Ax 2

15
2F
Tighten the screw with the hex key Y.
3A
Repeat steps 2A - 2F to connect the
beams without gearbox B2 and B3
with the remaining pillars Aand A1 .
3. Connect the side beams without gearbox
B2 & B3 to the remaining pillars A& A1
B3 x 1
B2 x 1
Ax 2
A1 x 1
B3
B2 A1
A
Yx 1

16
4. Slide in the two end beams C
This phase requires six persons and at least two stepladders.
Make sure that the stepladders are standing securely to avoid falling.
Only use ladders suitable for this kind of installation work.
4A
Stand the two structures built during
steps 2 and 3 in an upright position, and
place them at one end beam length
away from one another. Make sure that
one person is supporting each leg
Aand A1 to prevent the structures
from falling.
Reminder:
When determining the installation
direction of the product, please consider
the opening direction of the louvers as
well as the desired sunshade eect.
4B
Slightly loosen the 8 built-in screws at
both ends of the end beam C.
Yx 1
Cx 1
6 PEOPLE REQUIRED
one end beam
length
one end beam
length
Gearbox
open

17
4C
Slide the slot nuts of the end beams C
from above into the slots of the corner
pillars A.
4D
Once the beam is in the correct position,
tighten the 8 built-in screws on both
ends using the hex key Yprovided.
4E
Install the other end beam Cby
repeating steps 4B - 4D .
Cx 1
Yx 1
Cx 1
Yx 1
C
AA
C
A
A

18
5. Check the alignment of the frame and
the distance between the corner pillars
You are now almost done installing the main frame of the pergola. Please double check
to ensure all beams and pillars have been installed and tted correctly. You may have to
unscrew certain bolts during this step.
You will also need a tape measure and a spirit level to complete this step.
5A
Choose one of the corner pillars A
and work from this pillar. Choose this
pillar carefully as it will dene the nal
installation location of the pergola.
Use a spirit level to measure against
both of the inner sides to ensure that the
corner pillar is straight and level.
Make sure this corner pillar does not
move position during the remaining
installation steps.
5B
Measure the distances between the
adjacent corner pillars. Adjust accordingly
and ensure the distances match those
shown in the opposite gure.
Spirit level
Size a b
(m/ft) (mm) (inch) (mm) (inch)
3x5.3/10x17 2790.5 109.9 2485.7 97.9
3x6/10x20 2790.5 109.9 2790.5 109.9
3x7.2/10x24 2790.5 109.9 3400 133.9
3.6x5.3/12x17 3400 133.9 2485.7 97.9
3.6x6/12x20 3400 133.9 2790.5 109.9
3.6x7.2/12x24 3400 133.9 3400 133.9
bb
b
b
a
a
a

19
5C
Measure the diagonal distance between
the opposite corner pillars. Adjust the
other corner pillars accordingly until
both diagonal distances are equal.
You may have to repeat the above steps
after completing the remaining steps.
5D
Check that all corner pillars are straight
and level using a spirit level. If the corner
pillars or beams are still not level, this
means that your main building surface
isn’t suciently level, and that you will
need to raise the corner pillars that
are positioned lower than the others.
(Contact qualied workers if needed.)
Warning:
If you do not adjust the main structure
at this point, you may encounter
problems when tting the roof deck and/
or accessories to the frame.
Spirit level
Size c d
(m/ft) (mm) (inch) (mm) (inch)
3x5.3/10x17 3739 147.2 5802.5 228.4
3x6/10x20 3951 155.6 6343 249.7
3x7.2/10x24 4403 173.3 7457 293.6
3.6x5.3/12x17 4217 166.0 6120 240.9
3.6x6/12x20 4403 173.3 6635 261.2
3.6x7.2/12x24 4813 189.5 7706 303.4
c
d
d
c