Mircom TX3 Series User manual

Version 2.2 Mircom 1 (61)
LT-980 Copyright 2015
TX3 Series
TX3-CX CARD ACCESS SYSTEM
Installation and Operation Manual

2 (61) Version 2.2
Copyright 2015
Copyright 2015 Mircom Inc.
All rights reserved.
Mircom TX3-CX Card Access System Installation and Operation Manual v.2.1
This manual, as well as the software described in it, is provided under licence or other agreements
and may be used or copied only in accordance with the terms of such license. The content of this
manual is furnished for informational use only. It is subject to change without notice, and should not
be construed as a commitment by Mircom. Mircom assumes no responsibility or liability for any errors
or inaccuracies that appear in this book.
Except as permitted by such license, no part of this publication may be reproduced, stored in a
retrieval system, transmitted in any form by means electronic, mechanical, using any recorded
media, or any other format without the prior written permission of Mircom.
Mircom
25 Interchange Way
Vaughan, Ontario
L4K 5W3
905.660.4655
Fax:[phone]

Table of Contents
Version 2.2 TX3-CX Card Access System Installation and Operation Manual 3 (61)
LT-980 Copyright 2015
Table of Contents
1 Welcome 7
1.1 Introducing the TX3-CX Card Access System 8
1.2 Applications 8
1.2.1 Wiegand interface 8
1.2.2 Card Access System 9
1.3 Configurable Features 9
1.3.1 PC Configurator Software 9
1.4 Installer Responsibilities 10
1.4.1 PC Requirements 10
1.5 Network Setup 10
1.6 About This Manual 13
1.6.1 Version Control 13
1.6.2 Additional Documentation 14
1.6.3 Key Terms 14
1.7 Contact Us 14
1.7.1 General Inquiries 15
1.7.2 Customer Service 15
1.7.3 Website 15
1.7.4 Email 15
1.7.5 Technical Support 15
2 Configurable Features 17
2.1 Inputs 18
2.1.1 Request to exit for reader A or B 18
2.1.2 Door sense for reader A or B 18
2.2 Correlation 19
2.2.1 Assigning events to access points 19
2.2.2 Events 19
2.2.3 Actions 19
2.2.4 Panels 20
2.2.5 Output 20
2.2.6 Duration 20
2.2.7 Schedule 20
2.3 Access Criteria 20
2.3.1 Lock / Unlock 21
2.3.2 High security 22
2.3.3 PC decision required 22
2.3.4 Facility code mode 22
2.3.5 Card + PIN 23
2.3.6 Anti-passback 23
2.3.7 Temporary card 23
2.3.8 Interlock 23
2.3.9 Access level 23
2.3.10 Controller options 24
2.3.11 Access point options 24
2.3.12 Card options 26

4 (61) TX3-CX Card Access System Installation and Operation Manual Version 2.2
LT-980 Copyright 2015
2.4 Timers 27
2.4.1 Timer schedule 27
2.4.2 Unlock time 27
2.4.3 Extended unlock time 27
2.4.4 Anti-passback 27
2.4.5 Door held open warning 28
2.4.6 Door held open alarm 28
2.5 Schedules 28
2.6 Holidays 29
2.7 System Status 29
2.7.1 Common trouble 29
2.7.2 Common alarm 29
3 Installation and Setup 31
3.1 Grounding the Card Access System 32
3.2 Installing the Controller and Components 32
3.2.1 Optional Components 32
3.2.2 Installing the Card Access Controller 33
3.2.3 Installing the thermal kit 33
3.2.4 Installing the tamper switch 33
3.2.5 Installing the modem 33
3.2.6 Installing the IP Module 34
3.2.7 Installing the MD-993 module 35
3.3 Controller Board Description 36
3.3.1 Controller Panel LEDs 36
3.3.2 Controller Board Components 36
3.3.3 Power Supply 38
3.3.4 ON/OFF Switch and Battery Back-up 38
3.3.5 RS-485 39
3.3.6 USB Port 39
3.4 Connecting the Inputs 39
3.4.1 Inputs 1 to 8 40
3.4.2 Request to Exit 41
3.4.3 Door sense 41
3.4.4 General purpose input 41
3.4.5 Active state 41
3.4.6 Supervision requirement 41
3.4.7 Alarm Delay 43
3.5 Connecting the Outputs 43
3.5.1 Specific functions 43
3.5.2 Active state 44
3.5.3 Outputs 1 to 6 44
3.5.4 Outputs 7 and 8 45
3.6 Connecting the Card Reader 45
3.6.1 Card Reader Requirements 45
3.6.2 Card Reader Connection 46
3.6.3 Card Reader Status LEDs 47
3.6.4 Card Reader Beeper 47
3.7 Setting DIP Switches SW2 47
3.8 Setting Jumpers 51

Version 2.2 TX3-CX Card Access System Installation and Operation Manual 5 (61)
LT-980 Copyright 2015
3.9 Turning on the Controller 52
3.9.1 Default Configuration Values 52
3.10 Updating Firmware 52
3.10.1 Firmware Version Control 53
3.11 Beginning Configuration 53
Warranty & Warning Information 55
Special Notices 58

6 (61) TX3-CX Card Access System Installation and Operation Manual Version 2.2
LT-980 Copyright 2015
List of Figures
Figure 1 Basic Card Access System 10
Figure 2 Card Access System using an RS-485 network 11
Figure 3 Card Access System using an ethernet TCP/IP network. Controllers connected
to an ethernet network are Master Nodes. 11
Figure 4 Card Access System using both ethernet and RS-485 networks 12
Figure 5 Controller Back Cover Dimensions and Optional Component Location 32
Figure 6 Modem Board Location 34
Figure 7 IP Module Board Location 35
Figure 8 MD-993 Module 35
Figure 9 Controller Board Connection Locations 37
Figure 10 Power Supply 38
Figure 11 Controller Board Battery Wiring 38
Figure 12 RS-485 Connections 39
Figure 13 Controller Board Input Terminals 40
Figure 14 Input Terminal Sample Connections 40
Figure 15 Input - Supervised for Open 42
Figure 16 Input - Supervised for Short 42
Figure 17 Input - Supervised for Open and Short 43
Figure 18 Controller Output Terminal Sample Connections 44
Figure 19 Outputs 7 and 8 Sample Connections 45
Figure 20 Card Reader Connections 46
Figure 21 Controller Board Card Reader Connectors 46
Figure 22 Location of Jumpers JW1 to JW5 and Switches SW1 and SW2 51

Version 2.2 TX3-CX Card Access System Installation and Operation Manual 7 (61)
LT-980 Copyright 2015
1 Welcome
This manual provides information about the installation and operation of the
TX3-CX Card Access System, and must be read in its entirety before beginning
any installation work.
Installation must be performed by a qualified technician and must adhere to the
standards and special notices set by the local regulatory bodies.
Note: Mircom periodically updates panel firmware and Configurator
Software to add features and correct any minor inconsistencies.
For information about the latest firmware or software visit the
Mircom website at www.mircom.com.
For warranty and special notices information see the Warranty and Special
Notices chapter on page 55.
Warning: The Card Access System must be grounded by a qualified
electrician. An improperly grounded unit can result in
equipment malfunction and electrical shock.
This chapter explains
• The TX3-CX Card Access System
• Applications
• Configurable Features
• Installer Responsibilities
•Setup

8 (61) TX3-CX Card Access System Installation and Operation Manual Version 2.2
LT-980 Copyright 2015
Welcome
1.1 Introducing the TX3-CX Card Access System
The TX3-CX Card Access System is part of the Mircom suite of products that
provide building ready monitoring, control and integrated security solutions for
use in the high end multi-tenant residential market.
The Card Access System addresses the need within today’s high end multi-tenant
residential market for an easy-to-use tenant access system and an easy-to-use
configuration utility.
This manual provides the technician with information about the installation and
configuration of the Card Access System and explains how to configure various
components for a new system, including the modification of an existing system.
1.2 Applications
Mircom's Card Access System consists of a controller, two card readers and
configuration software. The controller can accept at the same time, a
combination of card readers with the 26-bit Wiegand, 35-bit Indala, 37-bit
Mircom, 50-bit RBH, and 32-bit CSN card reader standards to control two access
points or doors. The Card Access System can set elevator usage if elevator
controls are used.
A number of different card readers are supported, such as the TX3-CX-REC
Wiegand wireless receiver, all of which are configurable using the configurator
software.
The Card Access System can be used in a stand-alone or networked environment
using a standard RS-485, daisy chain peer-to-peer network arrangement.
This network can consist of only the Card Access Controller or a combination of
Touch Screens, Lobby Control Units, Elevator Restriction Units and Card
Access Units. Up to 63 units can be networked on any RS-485 network or
subnetwork. Valid RS-485 network addresses range from 1 to 63. One of the
networked units with a real time clock, such as Touch Screen, Lobby Control or
Card Access must have their network address set to 1.
If an ethernet network is used, you can connect more than 63 units to your system.
If you use an etherent network with RS-485 subnetworks, each RS-485
subnetwork can have 63 devices connected to it.
1.2.1 Wiegand interface
The Wiegand interface is a wiring standard for card readers for establishing the
connections between a card reader and the Card Access System. This interface is
a serial interface requiring 7 to 10 conductors for communications between the
reader and the controller. This interface also supplies 12V power to the reader.

Welcome
Version 2.2 TX3-CX Card Access System Installation and Operation Manual 9 (61)
LT-980 Copyright 2015
The Wiegand compatible access card has 26 bits of information embedded onto
the card. The card reader reads and registers the card information and sends it
back to the controller in a serial bit stream.
1.2.2 Card Access System
The Mircom Card Access System supports a proprietary 37-bit encoding
technology and a 26-bit SIA standard format, and consists of a maximum of 63
Card Access Controllers networked together. Each Card Access Controller can
have two card readers. The Card Access System provides an optional battery
backup and a real time clock.
The Card Access System integrates with the TX3 Telephone Access system by
utilizing a common network for both Telephone Access and Card Access
Systems.
A PC provides configuration and on-line monitoring of the Card Access System
and the Telephone Access System status. Once the system is configured, the PC
is not required.
1.3 Configurable Features
The system is configured by connecting the inputs and outputs to device access
points, and using the configurator software to establish the correlations between
these inputs and outputs.
Additional physical configuration is required using the dip switches and jumpers
on the controller. DIP switches set the Card Access Controller network address.
Jumper settings set the controller for firmware updates.
1.3.1 PC Configurator Software
The Configurator Software TX3-MSW is a combined Telephone Access System
and Card Access System configurator that uses a common database. Once the
controller is installed the system applies its default values. Use the configurator
software to fully configure the system. See the following documentation:
• LT-995 Configuration and Administration Guide
• LT-973 TX3 Software Guide

10 (61) TX3-CX Card Access System Installation and Operation Manual Version 2.2
LT-980 Copyright 2015
Welcome
1.4 Installer Responsibilities
The installation and setup must be done by a qualified technician. The technician
is responsible for installing all of the system components, connecting all of the
input and output wiring for the appropriate door entry systems, and ensuring that
the wiring adheres to the requirements of the system for proper operation using
the configurator software.
1.4.1 PC Requirements
The following are the PC requirements:
• Dual core processor
• 1.8 GHz, 1 GB RAM
• Windows XP or later
• USB Connection
1.5 Network Setup
The Card Access System can consist of either stand-alone Card Access
Controllers or networked Card Access Controllers. Networked Card Access
Controllers can communicate over an RS-485 network, an ethernet TCP/IP
network, or a combination of an ethernet network with RS-485 subnetworks. All
Card Access Controllers can communicate over RS-485. To communicate over
an ethernet network you need at least one IP-enabled Card Access Controller
(called a Master Node).
The TX3 Configurator software can connect to any of these network
configurations. How you connect to the network (that is, through TCP/IP, USB,
a modem, or the COM port) determines what devices you can configure on the
network using the TX3 Configurator. The different network configurations are
explained in the rest of this section.
Figure 1 shows a basic Card Access System with one Card Access Controller and
two card readers. The maximum distance between the Card Access Controller
and the card readers is 500 feet.
Figure 1. Basic Card Access System
Card Reader A Card Reader B
Card Access Controller