Mirion Technologies TelePole II User manual

15‐00143
 Revision1
 April2016

All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
TelePole II Telescopic Meter
User’s Guide
Prepared by: Reviewed by: Approved by:
Name
Date
Signature

15‐00143
 Revision1
 April2016

All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
TelePole II Telescopic Meter
User’s Guide








Document#15‐00143
Revision1 
April2016    


15‐00143‐1 TelePoleIIUser’sGuide Page|3
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
REVISIONLOG: 

Revision#

Date

RevisedPages

Comments

0
1
December2015
April2016
N/A
ALL
Initialrelease
Firmwareupdatestometerandexternal
detector.Addedfirmwareupdate
procedureandcalibrationwithoutusing
RMVCsoftware




15‐00143‐1 TelePoleIIUser’sGuide Page|4
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
TableofContents
1.THETELEPOLEIIMETER..................................................................................................6
1.1.GENERALDESCRIPTION............................................................................................................6
1.2.FEATURES..............................................................................................................................7
1.3.APPLICATIONS........................................................................................................................7
2.TELEPOLEGENERALSPECIFICATIONS..............................................................................8
3.TELEPOLEDETECTORSPECIFICATIONS..........................................................................10
3.1.WIDERANGEDETECTOR........................................................................................................10
4.OPERATINGINSTRUCTIONS..........................................................................................12
4.1.PREPARATIONFORUSE..........................................................................................................12
4.2.STARTING‐UP.......................................................................................................................14
4.3.THEDISPLAY........................................................................................................................15
4.4.GENERALFUNCTIONS............................................................................................................18
4.5.THRESHOLDSELECTION..........................................................................................................20
4.6.PUSH‐BUTTONSFUNCTION.....................................................................................................21
4.7.METERDISPLAY....................................................................................................................22
4.8.BATTERYREPLACEMENT.........................................................................................................22
5.COMMUNICATION.......................................................................................................24
5.1.METERBOXTOEXTERNALDETECTOR.......................................................................................24
5.2.METERBOXTOCOMPUTER....................................................................................................24








15‐00143‐1 TelePoleIIUser’sGuide Page|5
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
6.CALIBRATION...............................................................................................................26
6.1.PURPOSE.............................................................................................................................26
6.2.REFERENCES........................................................................................................................26
6.3.PREREQUISITES.....................................................................................................................26
6.4.SETUP.................................................................................................................................26
6.5.CALIBRATION.......................................................................................................................29
6.6 ManualCalibration
6.7 FirmwareUpgrade



15‐00143‐1 TelePoleIIUser’sGuide Page|6
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
1. TheTelePoleIIMeter

1.1. GeneralDescription
TheTelePoleIIisatelescopicgammameterdesignedtoobtaindoseratereadingsinwide
radiation fields. The TelePole II contains both an internal and external detector. The
internaldetector,mountedintheMeterbox,providesradiationmeasurementsfrom50
R/hto1.5R/h(0.5Sv/h–15mSv/h)inproximitytotheuser,whiletheexternal
detector,mountedontheendofthetelescopicpole,withitstwoGMtubes,providesa
widemeasurementrangeof50R/hto1000R/h(0.5Sv/hto10Sv/h).Thedisplayrange
startsfrom0.00mR/h(0.0Sv/h).
Therugged,lowmaintenanceTelePoleIIcanbeusedasastand‐aloneinstrumentorit
canbeintegratedasanAreaMonitorintoWRM2systems,usingexistingequipmentand
software.
TheTelePoleII’sauto‐rangingmeterutilizesacombinationdisplayofbothinternaland
smartexternaldetectorstoprovideasmootheddigitalreadoutforminimumfluctuation
andfastresponse.Theimprovedquarterlockingfour‐segment,poleextendstoeleven
feetlongandcollapsestothreeandahalffeetforeasytransport.TheTelePoleIIincludes
abuilt‐inmicroprocessor,datamemory,BluetoothandWRM2toprovidemaximumreach
backcapabilities.


Figure1‐1.TelePoleIIMeter

15‐00143‐1 TelePoleIIUser’sGuide Page|7
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
1.2. Features
 Widemeasuringrange.
 Rugged,sturdyconstructioncombinedwithlowcostreplacementparts.
 InternalWRM2900MHzor2.4GHzRadio
 Internalalarmthresholdsfordoserate.
 Colorcodeddisplayaccordingtofieldrange
 Dual‐outputdisplaycombinesastableandaccuratedigitalreadoutofboththeinternal
andexternaldetectors
 Displaybacklightoffersextrabrightillumination
 Built‐inUSBcommunication.
 ExternalUSBpowersupplyconnection.
 ExternalBluetoothheadphoneconnection(foralarmindicationonly).
 ExternalBluetoothandoptionalAlarmvibratingwristband
 CapabilitytoprovideAccumulatedDose
 Capabilitytoprovideadoserategraph
 CapabilitytostoredoseratereadingsanddownloadtoPC
 Easytouse,ergonometricmenuwhichcanbesetupusingexternalPCconfiguration
software.
 Built in LED (flashlight) on the external detector end to illuminate vicinity of the
measuringpoint
 Allowstheusertomanuallyselecttheloworhighrangetubeintheexternaldetector.
 SmartexternaldetectorthatiscalibratedseparatelyandcanbeusedonanyTelePole
IImeter.

1.3. Applications
 SupportsALARAprinciplesbyallowingoperatorstoobtainreadingsatadistanceofup
toeleven(11)feetaway.
 AlsosupportsALARAinthattheoperatorscanseetheirlocaldoseaswellastheremote
dosefromtheexternaldetector.

15‐00143‐1 TelePoleIIUser’sGuide Page|8
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
 WideRangeSurveyinstrumentthatallowsdatastorage.
 Real‐timedoseratemonitoringconnectedtoaWRMTelemetrySystem.Transmitted
data conforms to existing Mirion Technologies remote monitoring software (e.g.,
WinWRM2,TeleView3000).

2. TelePoleGeneralSpecifications
Measuringrange(External) 0.05mR/hto1000R/h(0.5Sv/hto10Sv/h)
 AutomaticswitchingbetweenthetwoGMtubesat
 1,500mR/h(ascendingdoserate)and400mR/h
(descendingdoserate)
Measuringrange(Internal) 0.05mR/hto1500mR/h
SmartExternalDetector  GMtubeZP‐1301(orequivalent)–highrange
  GMtubeZP‐1201(orequivalent)–lowrange
InternalDetector  GMtubeZP‐1201(orequivalent)‐lowrange
Measuringrange  0.05mR/hto1000R/h(0.5Sv/hto10Sv/h)
 AutomaticswitchingbetweenthetwoGMtubesat
 1,500mR/h(ascendingdoserate)and400mR/h
(descendingdoserate)
Accuracy 10%ofreading,withinthemeasuringrange
Energyresponse(Cs‐137)25%at65KeVto2.0MeV
Sensitivity(Cs‐137)  17cps/mR/h(internaldetector)

Datalogging  200datarecords
Display  Digitalforexternaldetectorrateanddose
  Digitalforinternaldetectorrate
Trendgraphforexternaldetectorrate
(3digitswithautorangingunitsofmeasurement)

Powersource  4x1.5VoltAA‐typealkalinecells,
   85hoursofcontinuousoperation

TemperaturerangeOperation: ‐20Cto+50C(‐4Fto122F)

15‐00143‐1 TelePoleIIUser’sGuide Page|9
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
 Storage: ‐20Cto+60C(‐4Fto140F)

Humidityrange  10%to95%RH(non‐condensing)

CasingMaterial  ABSHardPlasticMold
DetectorCasing  AnodizedAluminum
TelescopicPole  AnodizedAluminum

Dimensions Meterbox Width:35mm(1.4”)
  Length:170mm(6.7”)
  Breadth:115mm(4.5”)
Polelength Eleven(11)Feet

Weight   1951g(4.3lbs.)













15‐00143‐1 TelePoleIIUser’sGuide Page|10
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
3. TelePoleDetectorSpecifications

Note:TherearethreeotherExternalDetectorsthatwillbeafutureoption(Gamma‐Very
HighRange(VHR)),Gamma&BetaWideRange,andGammaHighlySensitive(XDS).Oncethese
areavailabletheinformationwillbeaddedinfuturerevisionstothismanual.

TheTelePoleIIenablestheusertoconnectanumberofExternalDetectors.Eachexternal
detectorcanalsobeusedindependentlytothemeterbysimplyconnectingittoaComputer
usingastandardUSBcable(USB2.0AtoMiniB)oftheTelePoleIIincludesthefollowingstate
oftheartfeatures:

1. Waterproof(IP‐67)detectorincludingwaterproofUSBconnection
2. BuiltinprocessortofacilitateindependentcommunicationswitheithertheMeterboxor
directlytotheRMVCsoftware.
3. Builtincalibrationfactorwhichfacilitieseasyandinstantswitchingofdetectors
4. QuickConnecttoTelescopicPole
3.1. WideRangeDetector

TheexternaldetectorcontainstwoGMtubesandmeasuresGammaandX‐Rayradiationonly.

GMTubes: ZP‐1301andZP1201(orequivalent)
MeasuringRange: 0.1µSv/hto10Sv/h(10µR/h–1000R/h)
Accuracy: ±10%ofreadingwithinthemeasuringrange
Energyresponse(Cs‐137): ±25%from65keVto2MeV
Sensitivity(Cs‐137): 0.3cps/mR/hand17cps/mR/h
PowerSource: StandardUSBcablefromMeterorComputer
Temperaturerange: ‐10oCto+50oC(15oF to 122oF)Operation
HumidityRange: DetectorisIP‐57rated
CasingMaterial: Blackanodizedaluminum
Dimensions: Diameter:33m(1.3”)x21cm(8.27”)Length
Weight: 220grams(0.5lbs)



15‐00143‐1 TelePoleIIUser’sGuide Page|11
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.

Calibrate/Measuringdirection(s)clearlymarked





ForInternaldetectorandExternalWideRangedetector:
Responsetimedependsondoseratechanges:

Radiationfield
[mR/h]
Responsetime
[sec.]
<0.6 45
0.6‐2.5 20–30
2.5‐20 5–10
20‐60 2–4
>60 2
<2R/h 2‐6
2R/h‐10R/h 2‐3
>10R/h 2

Theresponsetimefortheincreasinganddecreasingchangesinradiationfieldis
fasterandequalinbothinstances.Largechangesintheradiationfieldwillenable
theinstrumenttoreactalmostimmediately.
Theincreasedchangeintheresponsetimedependsonthecurrentreadingand
theextentofthechangeintheradiationfield.Generallyitwillbelessthan2sec.

GMTube
GMTube

15‐00143‐1 TelePoleIIUser’sGuide Page|12
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
4. OperatingInstructions
4.1. PreparationforUse
Removetheinstrumentfromtheshippingcontainerandinspectforanyphysicaldamage.
Inthecaseofdamage,reportitimmediatelytoMirionTechnologies.
Donotattempttoinstalloroperatedamagedequipmentsincesafetyandperformance
maybeaffected
NOTE:Themanufacturerrecommends that the end user / owner to perform periodic
inspections(duringdailyperformancechecks)ofthetelescopicpole,collars,andmeterto
ensureproperoperationaluseandsafety.

4.1.1 GeneralInspectionstobeperformed:
4.1.1.1 Checktheconditionofthepolesegmentsfreelyextendandproperlylock.
4.1.1.2 InspectthedetectorHeadforlockingringtightnessandpolescrewtightness.

Figure4‐1.DetectorHeadInspection

4.1.1.3 Inspectstrapholdersfortightness(ifthesecomponentshavebeenremoved–the
manufacturer recommends using Loctite221(orsimilar)compoundforwhenthe
componentsarereattached.

15‐00143‐1 TelePoleIIUser’sGuide Page|13
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.

Figure4‐2.StrapHolderScrewInspection



4.1.1.4 Meterconnectiontopole


Figure4‐3.MeterConnectiontoPole



15‐00143‐1 TelePoleIIUser’sGuide Page|14
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
4.2. Starting‐up
 Removethemeterfromthetelescopicpolebyunscrewingthetwoknurled
headedscrewsonthebottomofthemetermount.
 Removethebatterycompartmentcoverlocatedonthebottomofthemeter,see
section4.9
 Insertfour(4)1.5vAAbatterycellsintothebatterycompartment
 Connecttheexternaldetectortopoletopandhandtightenthethreadedcollar.
 PresstheON/OFFpush‐buttontoturnthemeteronbyholdingtheON/OFFbutton
forfive(5)seconds
 If the initial screen shows the serial number and firmware of the Meter and
Detector,theconnectionisestablished.
Followingasuccessfulself‐teststartup,themeterisreadyforuse.








Alerts/Alarms
St
ExternalDetector
ColorCodedFrame
(Thresholds)
SecondaryDisplay:
(InternalDetector)
MenuDis
p
la
y
Bar
IconDis
p
la
y
Bar
NoofSaved
DataRecords
Remaining

15‐00143‐1 TelePoleIIUser’sGuide Page|15
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
4.3. TheDisplay
4.3.1. IconDisplayBar

ICON Explanation Indication

BatteryCondition >5.2v3/3green
>5v2/3yellow
>4.6v1/3red
>4.1vemptyframe


IndicationofactiveGMTube
WR‐WideRange(Autoranging)
HR–HighRangeonly
LR–LowRangeonly
TheMenuenablestheuserto
manuallyselectoneofthethree
options,andtheactiveoptionwillbe
displayedhere.

FreezeModeActivated
Thehighestdoserateofthe
externaldetectorwillbefrozenon
thedisplay


Speaker
Activated


ExternalCommunicationActivated
WRM2orBluetooth


ExternalLEDONattipofExternal
Detector
Activated

123 Storedrecords Capableofstoring200datarecords








15‐00143‐1 TelePoleIIUser’sGuide Page|16
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
4.3.2. AlarmsSegmentandpriority
In case of malfunction in meter or detector function an audible and visual alarm will be
displayed,pressoneachofpushbuttonwillmuteaudiblealarm

ICON Explanation
D‐COM NoCommunicationbetweenExternalDetectorand
Meter
D‐LR TheExternalLowRangeGeiger(1201)is
malfunctioning
D‐HR TheExternalHighRangeGeiger(1301)is
malfunctioning
D‐HV HighVoltagetotheExternalDetectorismalfunctioning
D‐O.F OverflowConditiononExternalDetector(>1000R/h)
M‐O.F OverflowConditiononMeter(>4R/h)
ALARM OverthresholdCondition(ExternalDetector)
L.BAT Meterbatteryvoltagetoolow,mustbereplace.
M‐LR TheInternalDetector(1201)ismalfunctioning
M‐HV HighVoltagetotheInternalDetectorismalfunctioning
D‐CAL TheCalibrationtotheExternalDetectorisoverdue
M‐CAL TheCalibrationtotheInternalDetectorisoverdue
4.3.3. MenuDisplayBar(BasedonDefaultMenuSettings)
4.3.3.1. Freeze[FRZ]Mode
ThismodefreezesthehighestreadinguntiltheuserpushesFRZagaintorelease.AFreeze
icon willbedisplayedtoshowtheinstrumentiscurrentlyintheFreezemode.
4.3.3.2. Speaker[SPK]Mode
ThismodeactivatestheSpeakertoprovidepusheserroralerts.TheSPKIcon willbe
displayedtoshowtheinstrumentiscurrentlyprovidingaudiofeedbacktotheuser.
4.3.3.3. LED(LEDFlashlight)Mode
ThiscommandactivatestheLEDonthetipofthedetector.

PushMENUtoseethenextLine…

15‐00143‐1 TelePoleIIUser’sGuide Page|17
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
4.3.3.4. GRAPHMode
Thiscommandactivatesagraphinthelowerpartofthedisplay.Thehighestvalueofthe
graphisdisplayedtotheleftofthegraph.Thegraphdisplaysdataforaperiodof30
minutes,updateseverysecondfromrighttoleft.
4.3.3.5. THR(Threshold)Mode
Thiscommanddisplaysthethreealarmthresholdlevelsandwithassociatedcolors.The
thresholdlevelsaresetusingtheNEWversionoftheRMVC–configurationand
calibrationsoftware.
4.3.3.6. RANGEMode
ThiscommandallowtheusertomanuallyselecteithertheHR(HighRange),LR(Low
Range)orWR(WideRange)oftheexternalDetector.AnIcon(HR.LRorWR)willbe
displayedaccordingtotheselectedrange.

PushMENUtoseethenextLine…
4.3.3.7. TheDoseCommand
ThiscommandwilldisplaytheaccumulatedDoseoftheexternaldetectorsincethe
instrumentwaspoweredup.TheDosewillbeclearedwhenoncetheinstrumentisturned
OFF.
4.3.3.8. TheInternalDetector(INTDET)Command
ThiscommandisusedtoHide/Restorethedisplayoftheinternaldetector.TheDisplayof
theinternaldetectorisreplacedbytheGraph,DoseorANALOGfunctionwhentomenu
optionsareselectedfordisplaybytheuser.EveniftheGraph,Dose,orANALOGoptions
areturnedbackoffwithasecondbuttonpush,theInternalDetectordisplaymustbe
restoredbyselectingtheINTDETmenuoption.

4.3.3.9. ManualCalibration(CAL)Command
ThiscommandisusedtoactivatetheManualCalibrationfunction.Thisallowstheuserto
manuallyadjusttheFvaluesfortheExternalDetector(only).Onceselected,itrequiresa
secondpushtoconfirmthestartofthecalibrationprocess.Oncethecalibrationisdone,
removethebuttonsoitisnotavailableforthenormaluser.Ifnotremovedviathe
software,theCALbuttonwillremainasamenubuttonuntilthecalibrationiscompleted;
whenthemeterisnextturnedoffandbackonitwillbeautomaticallyremoved.See
Section6.6formoredetails.
OR

15‐00143‐1 TelePoleIIUser’sGuide Page|18
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
 TheANALOGCommand
TypicallythisbuttoniseitherCALorANALOG.TheANALOGcommandisusedtoactivate
theAnalogScalefunctionfortheExternalDetector.

PushMENUtoseethenextLine…
4.3.3.10. TheBrightCommand
Thiscommanddimsandbrightensthescreen.Itwilldefaulttothethirdbrightest
selectionuponpowerup.Usingbrighterscreenswillincreasepowerconsumptionand
reducebatterylife.
4.3.3.11. TheWRM2orBluetooth(Z/BT)Command
ThiscommandisusedtoactivatetheWRM2andBTtransmittersintheinstrument.The
firstpushwillactivatetheWRM2andsecondpushwillactivatetheBT(Bluetooth).An
appropriateicon( or )isdisplayedtoshowwhichoptioniscurrentlyactive.
See5.2.3forpairingprocedure.
4.3.3.12. TheStoreCommand
Thiscommandwillstoreupto200pointsofdoseratedata.Thenumberwilldecrease
eachtimethebuttonispressed ‐thedisplayednumberrepresentstheavailable
pointsremaining.ThisdatamaybeobtainedbyRMCintheRMVCsoftware.Oncethe
dataisviewedthroughthesoftwareandthewindowclosed–itwilldeletealldata.The
datamaybesavedtotheuser’scomputer.
4.4. GeneralFunctions
4.4.1. DoseRateDisplay
TheTelePoleIImeasuresDoseratesforboththeexternalandinternaldetectors:
ExternalDetectorRange:0.01mR/hto999R/h.
InternalDetectorRange:0.01mR/hto1.5R/h.

Readingsaredisplayeddigitallyandupdatedeverysecond


15‐00143‐1 TelePoleIIUser’sGuide Page|19
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
4.4.2. AutomaticRangeSwitchingforExternalDetector:
ThedetectorprobeassemblyincludestwoGMdetectors:Lowrange ‐ ZP‐1201 (or
equivalent),andhighrange‐ZP‐1301(orequivalent).
Inafieldof0.01mR/hto1500mR/hthefieldismeasuredbythelowrangeGeiger.In
case the radiation field increases above 1500 mR/h, the low range Geiger is
disconnected, and the radiation field is measured by the high range Geiger. The
switching between the low and high range Geigers is done at 1500 mR/h when the
radiationfieldincreases(lowrangeGeigerisdisconnected),andat400mR/hwhenthe
radiationfielddecreases(lowrangeGeigerisconnected).













Hi
g
h Ran
g
e
Low Ran
g
e
Overflow
Alarm
Field
1500 mR/h 1000 R/h
ZP 1301
ZP 1201
400 mR/h0.01 mR/h

15‐00143‐1 TelePoleIIUser’sGuide Page|20
All of the information in this document is the exclusive property of Mirion Technologies (MGPI), Inc. and is not to be disclosed,
reproduced, or used except as authorized in writing by Mirion Technologies (MGPI), Inc.
4.5. ThresholdSelections
4.5.1 TheTelePoleIIiscapableofstoringtwodoseratethresholdlevelswhichare
reflectedinthreecoloredframes(green,yellowandred)intheDisplay,andprovidea
visualindicationtotheuseroftheradiationlevelsdetectedbytheexternaldetector.
AboveThreshold2 
FromThreshold1toThreshold2 
From0.00mR/htoThreshold1 


4.5.2 ToviewthecurrentThresholdsettings,pushontheTHR(Threshold)commandin
theMenuDisplayBar.
Thefollowingwillbedisplayed:  THR<X THR.U=X
  THR<X
THR<X
4.5.3 AlarmThreshold(UserThreshold)‐AseparateAlarmthresholdcanbesetwhich
providesanaudibleandvisualalarmmessageinthecasewheretheexternaldetector
detectsaradiationfieldabovethesetthreshold.
4.5.4 BoththesethresholdsaresetusingtheexternalRMVsoftwarewhichavailable
offourwebsite.
