Mission LX CONNECT DAC User manual

User's Manual
LX CONNECT DAC
Scan the QR code using a smart-phone device,
for product warranty registration online.

1
Important Safety Instruction
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION!
WARNING: SHOCK HAZARD-DO NOT OPEN
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of non-insulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock.
WARNING: To reduce the risk of electric shock, do
not remove the cover (or back) as there are no
user-serviceable parts inside. Refer servicing to
qualified personnel.
This exclamation point within an equilateral triangle is
intended to alert the user to the presence of
important operating and maintenance instructions in
the literature accompanying the appliance.
WARNING: Only use attachments/accessories
specified or provided by the manufacturer (such as
the recommended battery - not supplied).
WARNING: The mains plug/appliance coupler/is
usedas disconnection device; the disconnection
device shall remain readily operable.
CAUTION: These servicing instructions are for use by
qualified service personnel only. To reduce the risk of
electric shock, do not perform any servicing other
than that contained in the operating instructions
unless you are qualified to do so.
Do not install this equipment in a confined or built-in
space such as a bookcase or similar unit, and keep
well ventilated in open space. The ventilation should
not be impeded by covering the ventilation openings
with items such as newspaper, table-cloths, curtains
etc.
WARNING: To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or
moisture. The apparatus shall not be exposed to
dripping or splashing and ensure that objects filled
with liquids, such as vases, shall not be placed on the
apparatus. No naked flame sources, such as lighted
candles, should be placed on the apparatus.
WARNING: Do not ingest the battery, Chemical Burn
Hazard. This product requires a coin/button cell
battery (not included). If the coin/button cell battery
is swallowed, it can cause severe internal burns in just
2 hours and can lead to death. Keep new and used
batteries away from children. If the battery
compartment does not close securely, stop using the
product and keep it away from children. If you think
batteries might have been swallowed or placed inside
any part of the body, seek immediate medical attention.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding plug. A grounding plug has two blades
and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at the plugs, convenience
receptacles, and at the point where they exit from
the apparatus.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart or rack
is used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
Ground protection terminal. This product
should be connected to a power outlet with
ground protection.
Denmark: Apparatets stikprop skal tilsluttes en
stikkontakt med jord, som giver forbindelse til
stikproppens jord.
Finland: Laite on liitettävä suojakoskettimilla
varustettuun pistorasiaan.
Norway: Apparatet må tilkoples jordet stikkontakt.
Sweden: Apparaten skall anslutas till jordat uttag.
WARNING: No naked flame sources, such as lighted
candles, should be placed on the apparatus.
WARNING: Attention should be drawn to
environmental aspects of battery disposal.
WARNING: Use of the apparatus in tropical climates.
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage

2
WARNING: When an amplifier is driven beyond its power output capabilities it
will produce distorted waveforms which will quickly damage your speakers by
overheating. Make sure that your amplifier is not left unattended when playing, for
example at parties, and turn the volume control down at the first sign of audible
distortion.
The Bluetooth® word mark and logos are registered trademarks, owned by Bluetooth
SIG, Inc. and any use of such marks by IAG Group Ltd is under license. Other
trademarks and trade names are those of their respective owners.
Being Roon Tested means that IAG Group Ltd and Roon have collaborated to ensure
you have the best experience using Roon, software and IAG Group Ltd equipment
together, so you can just enjoy the music.
For applicable power supplies see user instructions
aptX® software is copyright CSR plc. or its group companies. All rights reserved.
The aptX® mark and the aptX® logo are trademarks of CSR plc. or one of its group
companies and may be registered in one or more jurisdictions.
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage

3
Introduction
Welcome to Mission!
General Information
Misson is a brand that purveys lifestyle audio that fuses Hi-Fi heritage with contemporary design.
Music leads, technology follows.
The Mission LX CONNECT DAC is a stand-alone digital-to-analogue converter, pre-amp and
headphone amplifier, derived from the award-winning Mission LX CONNECT wireless speaker system.
It fuses the Mission mantra of innovative, attractive design and class-leading performance with the
latest audio technology, to enhance your audio experience.
Designed to function as a central console for all your music sources, with analogue, optical and coax
digital inputs, the Mission LX CONNECT DAC also features a dedicated HDMI ARC connection to
bring high fidelity, true wireless performance for TV, movies and games. It is even equipped with a
Bluetooth aptX receiver for wireless streaming of hi-resolution audio from tablets and smartphones.
The LX CONNECT DAC is controlled gracefully via the touch-sensitive display, or for even more
convenience you can use the included remote. The versatile connectivity options and compact form
factor means it can be used as the all-encompassing DAC and pre-amp interface for any amplifier,
active speakers, computer audio or head-fi system.
USB Drivers & Firmware Updates
To download Windows Drivers for PC USB, please see the separate user guide included with this
package.
Any firmware updates will also be available from www.mission.co.uk
Please read these instructions carefully before installing your loudspeakers. A few minutes
studying this manual will ensure a superb performance from your loudspeakers for many
years. Please attention to all cautions printed on the pages marked with this symbol.
Unpacking The Equipment
The carton contains:
The LX CONNECT DAC
One power adaptor
One plug for the adaptor suitable for your area
One remote controller
One user manual and a quick start guide
Please note: The remote control requires 1 x CR2025 type battery. Due to international shipping and
courier regulations with Lithium Ion batteries, the remote controller battery is not included in this
package.
Consult the dealer from whom you purchased the equipment if any item is not present. Carefully
unpack the unit and accessories.
Retain the packing materials for future use. Retain the user manual and information concerning the
date and place of purchase of your equipment for future reference. If you transfer the unit to a third
party please pass on this instruction manual along with the equipment.
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage

4
Connect your playback device via the via the auxiliary, optical, coaxial, PC USB, or AV audio inputs on
the rear panel.
Connect the LX CONNECT DAC mains supply.
When powered on, the LX CONNECT DAC indicator light will then illuminate dimly, which means it is
now in standby mode.
Either press the STANDBY button on the unit, or press the STANDBY button on the remote control
and the standby LED will turn on brightly. The screen will then briefly display the Mission logo,
confirming the unit is powered on. To return to standby, press the STANDBY button once more.
To adjust the volume, press the '+' and '-' buttons on the front panel of the unit or remote. Volume is
adjustable from 0 to 50. When the LX CONNECT DAC is restarted, the default volume is 25.
The DISPLAY button on the remote control will toggle the front panel display ON/ OFF. When the
display is OFF, use the front panel control or pressing any remote key will momentarily turn on the
display. After 10 seconds, the display will automatically turn o again.
Installing & Operating the LX CONNECT DAC
Controls & Functions
VOLUME UP
HEADPHONE OUT VOLUME DOWN STANDBY BUTTON
POWER LED
DAC
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage

5
Remote Handset
1. MUTE Press to mute and unmute the sound
2. STANDBY Press to bring the unit in/out of standby
3. VOL+ Increase volume
4. Press to start/pause Bluetooth/USB
Press to confirm page or setting selected in menu
5. Press to the previous track
Press to move to previous page or setting in menu
6. Press to the next track
Press to move to next page or setting in menu
7. VOL- Decrease volume
8. MENU Press to enter or exit menu
9. DISPLAY Press to cycle through display options
10. Press to select previous source
11. Press to select next source
STANDBY
MENU DISOLAY
MUTE
VOL+
VOL-
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage

6
Connections
Analogue Input
Connect your analogue sources to the line level input AUX IN.
Coaxial Digital Input
Connect your coaxial digital sources to COAX IN.
Optical Digital Input
Connect your optical digital sources to OPT IN.
The USB input enables you to connect a Mac or PC to the unit for playing audio files
stored on a computer. To use the USB input for the first time, a Windows PC will require
the installation of the USB driver. Download the driver via www.mission.co.uk. Please
refer to the USB and DSD Setup Guide supplied with the driver files. Connect your
computer to the unit via USB cable (type A to Type B).
LX CONNECT DAC is Roon Tested. Roon transforms the experience of browsing music;
artist photos, credits, bios, reviews, lyrics, tour dates; and composers are located
automatically, then interconnected by links to build a searchable digital magazine about
your music collection. Roon finds all the same links between your personal files and the
millions of tracks available on TIDAL, so you can start with the music you know, then
explore and discover new music from the world beyond your collection.
USB Input
AV AUDIO function allows you to send audio from your ARC-compliant TV to
LX CONNECT DAC through a single HDMI connection. To enjoy the AV AUDIO function,
please ensure your TV is both HDMI-CEC and ARC compliant and set up accordingly.
Please note: Your TV must support the HDMI-CEC and ARC function. HDMI-CEC and
ARC must be set to on. The configuration method of HDMI-CEC and ARC may dier
depending on the brand or model of your TV. For details about the ARC function, please
refer to your TV owner's manual. Only HDMI 1.4 cables can support the ARC function.
AV AUDIO
When selecting the Bluetooth input, the hub will display 'Pairing' which means the hub is
not yet connected to a Bluetooth device and is searching for one.
To connect, turn on the Bluetooth function on your smartphone, tablet or computer
device. Search for active Bluetooth devices. You will then see LX CONNECT DAC as an
option to connect. Select the LX CONNECT DAC option to pair to device and the hub
will then display “Connected” to confirm.
If you switch to an alternative input Bluetooth will disconnect automatically in 60
seconds, however when you switch back, Bluetooth will connect automatically to your
device once more.
Bluetooth Connection
Pre-Amplifier Output
Pre-amplifier (Pre Out) output for driving external power amplifiers, subwoofers or
signal processors.
A stereo 6.3mm (1/4") jack is provided on the front panel for connecting headphones.
When headphones are connected the Pre Out signal will auto cut o.
Headphone Output
LX CONNECT DAC UPDATE port is only used for updating the internal software or
service purposes. This is a non-user serviceable connection. Please refer to the Mission
website or your Mission dealer concerning updates or service.
Software Update
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage

7
Menu Options
To access additional controls over the LX CONNECT DAC, either press 'MENU' on your remote or
touch the MENU button on the front panel of the unit. This will give you dierent options: Digital Filter,
DSD BW, DPLL BW, Balance, Pre Delay, Brightness, Default Channel, Auto Standby, Pre Out Level,
Default Volume, Factory Reset, Update and Firmware. You can toggle through the dierent options
by pressing the '+' or '-' controls on the unit or left and right controls on the remote. The source button
on unit toggles between menu select and the menu parameter, or you can press the VOL+/VOL+
button on the remote. When you have selected a parameter to adjust, press the '+'or'-' buttons on the
unit, or left and right controls on the remote.
LX CONNECT DAC has a choice of 3 digital filters to oer the
best performance and compatibility with your digital audio files
and system:
Fast roll o: Standard flat response with fast frequency roll of
above Fs/2 (half the sampling frequency).
Slow roll o: Starts rolling of at a lower frequency than the Fast
filter but has a more gentle rate of attenuation. This is the
default filter for the LX CONNECT DAC.
Minimum phase: Has a gentle attenuation slope similar to the
Slow filter but with minimum phase characteristics. It can be
likened to an analogue filter applied in the digital domain.
Digital Filter (DAC, Only for Pre Out) Digital Filter
slowrolloff
Digital Filter
Minimumphase
Digital Filter
fastrolloff
The DSD Bandwidth can be widened to suit high performance
Hi-Fi equipment and particular DSD audio files.
DSD BW DSD BW
Normal
OPT DPLL BW
Normal
OPT DPLL BW
Wide
DSD BW
50K
DSD BW
60K
DSD BW
70K
DPLL setting is used for changing the bandwidth of the digital
phase lock loop of the D/A converter to accommodate dierent
levels of jitter on the incoming SPDIF signal.
Normal mode should be selected for signals with low jitter, while
Wide mode should be selected for signals with abnormal jitter.
For best audio quality leave this setting at the default value
Normal, only use Wide for a given input if the LX CONNECT DAC
is having problems locking onto the source.
OPT DPLL BW
Balance
3.0dBL+ -R
Balance
3.0dBL+ -R
Balance
0.0dBL R
Balance of left and right output channels (Pre Out) can be
adjusted in the unit's menu.
Balance
The brightness can be adjusted from a low level to a bright level,
adjustable in 8 increments.
Brightness Brightness
Level1
Brightness
Level8
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage

8
Default volume setting is for the max volume after you restart
the system. The default setting is 25, adjustable in 0 to 50.
Default Volume Default Volume
25
The final menu option displays the current firmware installed on
the LX CONNECT DAC.
Firmware Firmware
052.10
The LX CONNECT DAC UPDATE port is only used for updating
the internal software or service purposes. This is a non-user
serviceable connection.
Please refer to the Mission website or your Mission dealer
concerning updates or service.
Update Update
No
Update
Yes
The LX CONNECT DAC can be restored to factory default
settings.
Factory Reset Factory Reset
No
Factory Reset
Yes
The Pre Out level can be set to adjustable or fixed.
Adjustable level output is for purposes where the output level
should change with the master level output (for instance, when
connecting to powered subwoofers).
Fixed level output is for use with sources with built-in volume
control such as AV processors, where the input signal from the
hub should be constant.
Pre Out Level Pre Out Level
Adjustable
Pre Out Level
Fixed
LX CONNECT DAC has three standby modes, editable via
the menu.
Auto Standby Never: LX CONNECT DAC will only enter
standby through user control.
Auto Standby 20 Minutes: If there is no input signal for 20
minutes, the LX CONNECT DAC will enter standby.
Auto Standby 1 Hour: If there is no input signal for 1 hour, the
LX CONNECT DAC will enter standby.
Auto Standby Auto Standby
Never
Auto Standby
1 Hour
Auto Standby
20 Minutes
Any channel can be set as the default channel. Additionally, this
can be set, using the 'Recall Last Input' feature.
Default Channel Default Channel
USB
Default Channel
Recall Last Input
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage

9
System Operations
The LX CONNECT DAC features optical, coaxial, PC USB, AV audio and RCA inputs on the rear panel
with an additional Bluetooth aptX connection for wireless integration of laptops, smart phones and
tablet devices. It is controlled gracefully via the touch sensitive display, or for even more convenience
you can use the included remote control.
LX CONNECT DAC will work as a stand-alone DAC with a built-in headphone output and pre-output.
You can connect it to your amplifier or existing system, for use as a Hi-Fi grade DAC.
Change source / volume and
menu parameters with the
included remote.
Connect any Bluetooth
device and enjoy wireless
playback with the aptX
codec for CD-like sound
quality.
Mission LX CONNECT DAC via
RCA, optical, coaxial, PC USB and
AV audio connections.
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage

10
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage
Warranty Coverage
Online Registration
Mission warrants its products, subject to the following terms and conditions below, to be free from
defects in materials and workmanship.
The three (3) year extended warranty is applicable to items purchased from Jan 1st 2021, onwards.
Items purchased prior to this date are not eligible for this extended warranty service but are subject
to statutory warranty claims and all applicable consumer rights.
To qualify for the extended 3 year warranty, you must register your product within ninety (90)
calendar days from the date of purchase. Visit mission.co.uk/warranty-registration to complete your
online registration. Items not registered online will have a Limited Warranty for one (1) year, or for the
period of your country’s statutory warranty, whichever is longer.
Warranty can only be oered to products registered with proof of purchase with date, model and
details of the authorised dealer clearly stated on the receipt/invoice. Please keep the original
receipt/invoice in case it is required for a warranty claim.
This Limited Warranty is non-transferable and is oered exclusively to the original owner.
This Limited Warranty is valid only in the original country of purchase.
Repairs or replacements are provided under this warranty are the exclusive remedy of the consumer.
Mission shall not be liable for any incidental or consequential damages for breach of any expenses or
implied warranty with any product. Except to the extent prohibited by law, this warranty is exclusive
and in lieu of all other warranties whatsoever, both expressed and implied, including but not limited to
the warrant of merchantability and fitness for practical purpose.
This warranty provides benefits that are additional to and do not aect your statutory consumer
rights.
This Limited Warranty oer is subject to correct information being submitted in your application.
Incorrect dates or mismatched purchase receipt dates that are outside of the warranty terms will
immediately invalidate any warranty claim.
*Please check with your dealer local distributor for further information.
Scan the QR code using a smart-phone device,
for product warranty registration online.
Exclusions
The following items are excluded from the Mission warranty:
Normal wear and tear and cosmetic damage (including but not limited to any wear from reasonable
use, environmental deterioration or neglect)
Products on which the serial number has been removed, altered or otherwise made illegible.
Products not purchased from an authorised Mission dealer.
Products that were not new at the time of original purchase.
Products sold ‘as is’, ‘as seen’ or ‘with faults’
Product not purchased from an Authorised Dealer/Distributor within the region of the claim (ie
parallel imports or grey market products)

11
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage
Accidental damage or faults caused by commercial use, acts of God, incorrect installation, incorrect
connection, incorrect packaging, misuse or careless operation or handling which is not in accordance
with the user instructions.
Equipment that has been operated in conjunction with unsuitable, inappropriate or faulty apparatus.
Repairs, alterations or modifications carried out by parties other than Mission or its authorised service
partners.
Damage in transit that cannot be attributable to the fault of Mission, the authorised distributor or
dealer (ie. claims otherwise covered by transit insurance.)
Faults relating to abnormal or inappropriate power supply voltage or power surges.
Faults relating to extremities in temperature, exposure to heat, water or other liquids, insects,
excessive moisture, sand, chemicals, battery leakage or any other contaminants.
Any force majeure events, including but not limited to any acts of God, fire, lightning, typhoon, storm,
earthquake, hurricane, natural disaster, tsunami, flood, war, riot, public disturbance.
Any other causes beyond the reasonable control of either Mission and its Authorised Distributor.
Please note items purchased before 1st Jan 2021 are not eligible for the extended warranty claim.
How to Claim
To obtain warranty service please contact the authorised dealer from which you purchased this
product and present the limited warranty certificate oered upon registration of your product’s
extended warranty oer.
Do not dispatch goods without the prior agreement of the dealer distributor or authorised service
centre.
If asked to return products for inspection and or repair, please pack carefully preferably in the original
carton or packaging aording an equal degree of protection and returned via insured, trackable
courier service.
The authorised dealer or distributor will oer full return details and instructions. However, please note
if unsuitable packaging is used the warranty may be deemed void due to improper action in return.
Mission or the authorised distributor, dealer or service centre may make a charge for the supply of new
packaging for the return of the repaired item. Please note, insurance is recommended as goods are
returned at the owner’s risk. Authorised distributors or service centres cannot be held liable for loss or
damage in transit. insurance and freight charges on the return journey will be paid for by Mission,
authorised dealer, distributor or service centre if corrective work proves to be necessary.
In the event of ‘no-fault found’ or ‘no repair necessary’, the return shipping charge will be the
responsibility of the owner.
Repairs
All repairs will be carried out by the appointed distributor (or locally appointed service centre). Repairs
handled or processed without authorisation or approval of the appointed representative will be
excluded from this limited warranty. Please note, Mission is not able to supply parts or replacement
items to any other entity than the ocial distributor or authorised service centre.
Other than the warranty and services set out in this warranty, to the fullest extent permitted by law,
Mission shall not be liable to you and/or any third party or entity whatsoever for:
Any loss, damages and/or malfunction caused to any product(s) which is/are connected to any of
the products covered by this warranty.
Any damages, loss and liability, whether direct, indirect, incidental, consequential special, punitive or
otherwise, howsoever caused by, arising out of or otherwise, in relation to the installation, delivery,
use, service, repair, replacement and/or maintenance of the product;
Any damages, loss and liability under this warranty in respect of any act, omission, or negligence of
any of their technicians, employees, agents, representatives or independent contractors relating to
the actual or purported performance of any of the obligations under this warranty.

12
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage
Should a fault occur with your loudspeakers, please pack it correctly, using the original packing, so you
can ship it safely. Product for service should be returned to the appointed dealer from whom you
purchased the product. If you experience difficulties or there is no Mission dealer in your area, contact
the Mission distributor or the office below.
IAG Service Dept.
13/14 Glebe Road
Huntingdon
Cambridgeshire
PE29 7DL
UK
Tel: [phone]
Email: [email protected]
For information on other authorised service centres worldwide contact Mission International, UK.
A worldwide distributors list is available on the Mission website: www.mission.co.uk
Service Centre Address

13
IntroductionConnectionsMenu OptionsSpecifications Important
Safety Instruction
Controls
& Functions
Remote
Handset
System
Operations
Warranty
Coverage
Specifications
Model
General Description
Analogue Input
Digital Input
Analogue Output
Pre Amplifier
Input Sensitivity
Input Impedance
Variable Output Voltage
Output Impedance
Frequency Response
Signal-to-noise Ratio (S/N)
Total Harmonic Distortion
Sampling Rate
Digital Filters
Dimensions
Height (on feet)
Width
Depth (with terminals)
System
Outer Packaging
Net Weight
Gross Weight
Finish
Power Requirements
LX CONNECT DAC
Digital-to-Analogue Convertor, Headphone Amplifier and Pre-amp
RCA (AUX)
OPT, COAX, PC USB, Bluetooth, AV Audio
RCA Pre Out
300mV (AUX IN, volume = MAX)
13K (AUX IN)
0 – 3.2V
100 ohm
20Hz-20kHz (+/-0.3dB)
> 100dB (AUX IN, A-weighted)
> 110dB (digital Inputs, A-weighted)
< 0.001% (digital sources)
< 0.005% (analogue sources)
24bit - 192kHz (OPT, COAX)
32bit - 384kHz (USB, PCM)
2.8M for DSD64, 5.6M for DSD128, 11.2M for DSD256 (USB, DSD)
Fast Roll-o, Slow Roll-o, Minimum Phase
55mm
225mm
231mm
418 x 280 x 85mm
1.75kg
2.65kg
Black
Adapter - Input: 100-240Vac (50/60Hz) Output: 12V 1A

14
Correct Disposal of this product. This marking indicates that this product should not be disposed
of with other household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer where the product was purchased. They can
take this product for environmentally safe recycling.

IAG House, 13/14 Glebe Road, Huntingdon, Cambridgeshire, PE29 7DL, UK
Tel: [phone] Email: [email protected] www.mission.co.uk
IAG reserves the right to alter the design and specifications without notice. All rights reserved © IAG Group Ltd.
Mission is a member of the International Audio Group.