MISUMI MTCTR User manual

DIGITAL TEMPERATURE CONTROLLER

- 1 -
＊Thank you for purchasing Digital Temperature Controller. Please go through this Instruction Manual carefully
and use the unit in proper manner.
NOTICE/WARNING BEFORE OPERATION USE
The following symbol is provided to prevent incident or damage. Kindly refer to the details of the
WARNING/CAUTION when using for the first time.
● Make sure the correct wiring connection before turning on electricity.
Miss-Wiring may cause malfunction of the unit and fire.
● Never modify the unit to prevent damage or incident such as malfunction and fire etc.
● For prevention of its malfunction, do not push the front key with sharp points.
● Spare terminal must not be used for other purposes.
・Please put this user's manual aside for your reference, when operating the unit.
・Copy or reprint of this manual, wholly or partially, is not allowed.
・The contents of this manual may change without notice in future.
OPERATING ENVIRONMENT

Neveruseinthefollowingenvironments. It may cause fire and break the wire.
1）Around explosive gases, inflammable gases or corrosive gases
2）In either sunshine or ambient temperature (above 50℃) remarkably increases
3）In very low ambient temperature (below 0℃), such as outdoors in cold areas
4）In very high humidity (85%RH or higher)
5）Around splashing of water or chemicals
6）Under severe vibration or shocks
7）Around dust, iron powder, black smoke
8）Around external noise, induction trouble, vibration, large shocks, and others such that can have damaging
effects to the electric circuit.
9）Under violent temperature change
SPECIFICATIONS
Type MTCTR：RelaycontactMTCTS：SSR drive voltage
Power Supply Voltage 100 to 240V AC, 50/60Hz
Power Consumption Below 10 VA
Memory Element EEPROM
Input of Sensor Thermocouple,R.T.D./0-5V,1-5V,4-20mA (Changeable by front key)
Control Output Relay contact, SSR drive voltage, Current
Control Method Two kinds of PID,ON/OFF
Operation
Environment 0 to 50℃,20 to 90%RH(Avoid making dew)
Storage Environment -25 to 70℃,5 to 95%RH(Avoid making dew)
Weight Less than 180g
Location of the Unit
Setting Keep away from the followings.
・Gas of corrosion, dust and oily smoke.  ・The electric noise of generator
・The influence of electromagnetic field.・Mechanical vibration and shock.
・The direct sunlight.
Installation condition Installation category Ⅱ
DIGITAL TEMPERATURE CONTROLLER USER'S MANUAL2007.3（The 1st edition）
Due to mishandling, serious dangers may occur to the operator such as death,
electrocution and a skin burn.
WARNING
CAUTION
Due to mishandling, it may cause some damage to the unit or the operator
getting slight injury.
WARNING
CAUTION

- 2 -
CAUTION BEFORE CONTROL                  

・Set-upprogramisstoredoperation, as non-volatile memory, is equipped with the controllers.
・Either thermocouple or R.T.D.(Pt 100/JPt100) is selectable input type, but Current/Voltage input needs to be
selected individually. For suitable application, please select most appropriate input type and adjust input setup.
(※Thermocouple at the time of shipment (K) )
・PID or ON/OFF control is selective for the optimal perform and each detail of features is specified in the table
below.
 ※PID constants are automatically calculated and written in, when control begins or SV is altered on self-tuning.
PID Control ON/OFF Control
Merit Better control result is achieved as
opposed to that of ON/OFF control. Life span of relay is generally longer, as it is ON when SV and it is OFF when temperature is over SV (For heating control).
Demerit Life span of relay is shorter, as output
exists frequently with relay contact. Control value is worse in comparison with that of PID control.
PARTS INDICATION
PV Processvalue,characterforsetting
modedisplay.
SV Settingvalue,inputvalueforsetting
modedisplay.
OUT1

LightsONwhenoutput1turnON
OUT2

LightsONwhenoutput2turnON
AL1 LightsONwhenEventoutput1turnON

AL2 LightsONwhenEventoutput2turnON

COM

FlashONandOFFwhencommunicating.
LightsONwhencommunicationis
selectedasanoption.
RDY LightsONunderReady
DI LightsONwhenDIturnON
MODEKEY

Forchangeofdisplay
FUNCKEY Foractionoffunctionsetting
▲▼KEY Updownkeyforchangeofsettingvalue.
Holdingtheupdownkeysarethevalueata
rapidrate.
※ partisnotused.
INSTALLTIONANDWIRING

1)OuterDimensions
2)PanelCutout
(48×No.ofunits−3)
48
60 2 77
59
Attachment
Case (black)
Packing
48
Front
A
60 or more
A A
A：45mm tolerance：+0.6 -0

- 3 -
3)Wiring

CAUTION
For prevention of electric shock, please connect wiring only
after turning power off and don’t touch the terminal part
when powered on.
PRECAUTIONS ON WIRE CONNECTION  

1) Whenconnecting wires, be sure to turn off the power supply in advance, or electric shock may result.
2) This unit will not perform control operation for approx. 4 seconds after turning on the power. Note this point
when using the unit as an interlock circuit, because no output is issued during this period.
3) Use the crimping terminal for wire connection that fits M3.5 thread.
(Tighten the wire directly at the center portion)
4) Use wire with line resistance 5Ωor lower (per line) for connection between the temperature measuring
resistor and the temperature controller, and use the specified compensation copper wire or strand itself for
connection between the thermocouple and temperature controller.
5) When using the unit in the vicinity of a noise source, use shielded wire. Do not lay input and output lines
together in the same duct or conduit tube.
6) Separate the input and output signal lines 50 cm or more from the power supply line and load line.
①  ⑥  ⑪
②  ⑦  ⑫
③  ⑧  ⑬
④  ⑨  ⑭
⑤  ⑩  ⑮
OUT1
Relay output②
250V AC, 3A 
(Loadresistance) ③
SSR drive voltage
＋②
12VDC output  −③
POWER ON
100V to 240V AC 50/60Hz 10VA ④
(NOpolarity)
AC100V〜240V 50〜60Hz 10VA  ⑤
EV2(Foralarm)
①⑥
Relayoutput250V AC2.4A(Load resistance)
EV1 (For alarm)
⑪ Relayoutput
250VAC,2.4A
⑫(Loadresistance)
SensorInput
⑬bB⑬−
⑭B⑭＋
⑮A
RTD TC

- 4 -
SET-UP PARAMETERS BEFORE USAGE

・Follow the instructions below to set-up parameters
*If advanced set-up is required, refer to “Operation Flow and Setting”screen.
ParameterNo
1
Referto[Table1.Input Sensor Selection/Setting Range] and set to the input
settings of the sensor you are using (Refer to Default settings) SET1 2. Input type setting
↓
2
Set Yes/No of decimal requirements. (Refer to Default settings) SET1 6.
Position of decimal point
↓
3
Refer to “Caution before Flow”and set the control alternatives available for
Output 1.
Recommended settings
Main Unit: SSR outputPID Control
Main Unit: Relay contact output ON-OFF control(Refer to Default settings)
SET2 13.
Selection of control type
setting
↓
4
Set according to Heating control (0:Reverse) or -Cooling Control(1:Normal)
(Refer to Default settings) SET2 14. Change of normal or
reverse
↓
5
If alarm output is required, set Upper and Lower limit setting values. Refer to
“Alarm Operating Range”table shown on P5.
The Alarm Operating Range compares the measured value and present value
to turn the event on or off. It is effective for monitoring abnormalities or
starting/stopping of other systems.
SET3 38.／SET4 48.
Function setting for EV 1
Function setting for EV 2
(Refer to Ex.5.)
↓
6
Set ＳＶ Operate mode display
Primary displays
↓
7
Set ＡＴ(Auto Tuning) *When using PID control
Default values are pre-set for PID. Default values can be used, but in order to
stabilize controls, please perform AT.
AT Calculations depend on the kind of control.
Select 1, and press FUNC key to startAT.
Press the FUNC key once more during operation to stop.(Refer to Default
settings)
SET2 16
Setting for PID tuning
type
↓
8
Other
Check each movement. (Stable temperature/Alarm)
Setting of mis-operation(SV limiter/ Keylock)
Table1．To select input sensors and setting range. (unit:℃)
Symbol Low limit〜High limit 0.0Setting
00: K Thermocouple -200〜1372 -199.9〜990.0
01: J 〃-200〜850 -199.9〜850.0
02: R 〃0〜1700 −
03: T 〃   -200〜400 -199.9〜390.0
04: N 〃   -200〜1300 -199.9〜990.0
05: S 〃 0〜1700 −
06: B 〃 0〜1800 −
10: Rt100 -199〜500 -199.9〜500.0
11: JPt100   -199〜500 -199.9〜500.0
Setting of shipment
SET1 2. Input type setting  00：KThermocouple
SET16.Position of decimal point 0：Not required
SET2 14. Change of normal or reverse 0：Reverse
SET338.／SET4 48.
Function setting for EV 1 00：None
Function setting for EV 2  00：None
SET2 16
Setting for PID tuning type  1：Auto-tuning output 1

- 5 -
ALARM OPERATING RANGE 
Deviation
highandlow
limit
AL1L AL1H
 △
Absolutevalue
high and low
limit
AL1H
AL1L
0
Deviation
highlimit AL1H
 △
Absolutevalue
highlimit AL1H
0
Deviation
lowlimit AL1L
 △
Absolute value
lowlimit AL1L
0
Deviation
highandlow
limit range
AL1L AL1H
 △
Absolutevalue
high and low
limit range
AL1H
AL1L
0
△：Position of Setting value AL1L:Lower limit setting value AL1H:Upper limit setting value
：EventONarea
*Theabove alarm settings (AL1L, AL1H) apply for when positive values are set.
1. Power ON
Automatically
2. Initial Display
Automatically
3. Operation Mode
Press MODE Key (10sec)
4. Immediately after the "Blink",
press FUNC Key, and quickly
press MODE Key.
5. Press MODE Key (3 sec)
6. Press UPKey(△)for 1 →7
7. Press FUNC Key
8. Power OFF
9. Power ON
10. Initial Display
Automatically
11. TIMER Setting Mode
(OPERATION Mode)
12. Press UP Key (△)
for 1 →7
13. Go on TIMER Setting
Press
MODE Key consecutively
_ I n P
00
Processvalue
Settingvalue
SE t 7
oFF
S E t
１
_ C k F
oC
●HowtoreleaseBLINDFunction
_ C k F
oC
_ S u 1
on
SE t 1
on
taking4sec
(Blink once)
SE t 7
on
Processvalue
Settingvalue
taking 4 sec
**1 Please select an appropriate character
(eg. Timer Setting etc) being of BLIND
Function effect for the demanding release.
**2 Character selected for TIMER Setting.
**3 BLIND Function for "SELECTION
DISPLAY (Timer Setting Mode)" is released.
**1
**2
**3
_ I n P
00
S E t
1
S E t
7

- 6 -
OPERATION FLOW AND SETTING MENU


MODE key
MODE key, return to A
●Operate mode display
●Power ON
Shows for 4 seconds
(Warming up)
A. Primarydisplays
Process value PV Set the temperature
Setting value SV required
B. Priority displays. Refer to Ex.1.
SET0: Priority displays by setting and
shows max.9 displays by setting.
●FUNC key
FUNK key operates on the
selected setting mode 7. Refer
to Ex.2.
Ex.1. Priority displays & its setting
This function is to shift the most essential screens on
setting mode into operation mode as a priority. Please
select priority displays through priority display setting.

eg：

＊Screenisshiftedwhenpressing mode key each time.
Ex.2. FUNC key work
This function is to enable FUNC key to use as a specific
key, for the following actions selected in FUNC key setting
belonged to setting mode.
1. Digit shift
Setting digit shift is enabled when setting value is
changed.
2. RUN/READY
Control stop (READY) and control performance (RUN) are
alternately switched every FUNC key is pressed. (READY
lamp is ON during control stop)
3. Auto-Tuning (AT)
AT starts instantly after pressing FUNC key. (Start/Reset
operation is available, each time FUNC key is pressed)
  
4. Timer
Available for start/reset.
Press MODE key more
than 2 seconds
●Setting mode
Ex.3. To select PID
Feature of type A and B
Type A Ordinary PID
Type B Over shoot protection PID
If control is unstable under self-tuning, please
change to type Aor B and also to ON/OFF-control.
Ex.4. ARW
Anti-reset wind-up take effect for overshooting by
over-integral of PID control action.
・ARW controls integral action (PV accords with
SV).
・If integral value goes down, it takes effects.
If integral value is set "0", it stops integral
action.
Basic display Output 1 manipulated value
Setting high limit for event Output 1

- 7 -
 (Thenumericalvalueofdisplayisaninitialvalue.)
▲key ▲key
PV Initialsettingmode PV Controlsettingmode PV
SV Callingdisplay ▼key SV Callingdisplay ▼key SV
MODEkey MODEkey MODEkey
PV Selectinputtype PV PV
SV RefertoTable1. SV SV
MODEkey MODEkey
PV PV
SV SV
MODEkey MODEkey
PV PV
SV SV
MODEkey SV Controlperformance
SV Non-controlperformance
(Manipulatedvaluelowlimiteroutput)
PV SV Manualcontrol
SV MODEkey MODEkey
MODEkey PV
SV PV
PV SV SV
SV MODEkey
SV Notrequired PV
SV Required SV
MODEkey MODEkey
MODEkey
PV Selectablebelowfunctions PV
SV PV SV
SV None SV MODEkey
SV Changeofdigit SV 0：Reverse(Heating)
SV RUN/READY 1：Normal(Cooling) PV
SV Auto-Tuning MODEkey SV
SV Timer MODEkey
MODEkey PV
SV PV
PV SV
SV
SV None
SV Alllock(Notavailable)
SV Operationmodelockonly
SV Exceptoperationmode
MODEkey(returnto1)
MODEkey MODEkey
PV Tunessuitablysettingvalue PV PV
SV SV SV
SV Auto-tuningoutput1 MODEkey SV Normalopen
SV Self-tuningoutput1 SV Normalclose
SV Auto-tuningoutput2 PV MODEkey(returnto37)
SV Self-tuningoutput2 SV
SV Auto-tuningoutput1.2 MODEkey
PV
SV
MODEkey MODEkey(returnto9)
PV ＜WhenselectON/OFFControl＞
SV PV
MODEkey SV MODEkey
PV
SV PV
SV
MODEkey MODEkey(returnto9)
PV
SV MODEkey
PV
SV MODEkey
PV
SV MODEkey
PV
SV MODEkey
PV
SV MODEkey(goto24．)
Forsettingofmanipulatedhighlimit
value.(output1)(%)
ForsettingOFFpositionof controloutput1.
Adiustscontrolsnsitivityof ON/OFFcontrol
foroutput1.
ForShifting proportionalband.
Forsettingofmanipulatedlowlimit
value.(output1)(%)
25.Lowlimitsettingofmanipulatedvalueforoutput1
Displayofhighlimitsettingof
settingvalue.
(WithinsettingrangeofTable1)
Displayoflowlimitsetting
ofsettingvalue.
(WithinsettingrangeofTable1)
Usableforcontrolmodesetting
Selectableandswitchablebelowcontrolmodes.
13.Selectionofcontroltypesetting
AdjustsARWby%0.0〜100.0(-
10.0〜110.0%)
34.OFFpositionsettingforoutput1
Adjustsproportionalbandfor
output1(%perSLL〜SLH)
Adjustsintegraltime
0〜3600(second)
Adjustsdeviativetime
0〜3600(second)
Adjustsproportionalcycletime1
〜120(second)
23.ARWsetting(seeEx.4)
EV1settingmodeCalling
display
Setsensitivitywhen
required(℃).
Setdelaytimerwhen
required(sec).
Foroutbreakofsensorand
heaterabnormal
38.FunctionsettingforEV1
39.HighlimitsettingforEV1
40.LowlimitsettingforEV1
41.ControlsensitivitysettingforEV1
Selectbelowfunctions.
Sethighlimitvalue.
Whenmeasurementvaluecomes
anerror,setthecorrection
value(Addition)
CRfiltereffectisoperationalon
softwarewhenmakingfirst-order
lagoperationtoprocess
value(PV)
Keylocksettingforprotectionof
erroroperation.
Selectablebelowfunctions
Thermocouple/R.T.D(Pt100,JPt100)
7.FUNKkeysetting(RefertoEx.2.)
5.Filterinput
6.Positionofdecimalpoint
＜SET3：EventOutput1＞
37.Eventoutput1Setting
＜SET1：InitialSetting＞
1.InitialSettingdisplay ＜SET2：ControlSetting＞ 9.InitialSettingdisplay
20.Integraltimesetting
16.SettingforPIDtuningtype
Auto-tuning:Selectabove1･3or5and
pressFUNCkeyonce.Calloffautotuning:
pressFUNCkeyonceonoperating.
44.PolaritysettingforEV1
Normalopen/closeisselectable
whileeventoutputisON.
33.Contorolsensitivitysettingforoutput1
31.Manualresetsetting
17.ATcoefficientsetting
18.ATsensitivitysetting
19.Proportionalbandsettingforoutput1
Coefficientismultipliedby
proportionalbandvaluecomputed
atauto-tuning.
Sensitivityissetupduring
ON/OFFcontrolatauto-
tuning,particularywhenPVis
fairlyunstable.
10.HighlimitsettinginSVlimiter
11.LowlimitsettinginSVlimiter
21.Deviativetimesetting
22.Proportionalcyclesettingforoutput1
8.Keylocksetting
3.PVcorrectiongain
4.ZeropointsettingforPVcorrection 12.Keylocksetting
2.Inputtypesetting
Whenmeasurementvaluecomes
anerror,setthecorrection
value(Multiplication)
Setlowlimitvalue.
14.Changeofnormalorreverse
15.Manipulatedvalueforoutput1(%)
42.DelaytimersettingforEV1
Switchablebelowcontroloutput
actions.
Showsprocessmanipulatedvalue
foroutput1,andsettingthevalue
onmanualcontrol.
Displayrange:0.0〜100.0%
(-10.0〜110.0%)
Settingrange:Manipulatedvalue
low/higelimiter
24.Highlimitsettingofmanipulatedvalueforoutput1
43.AbnormalforEV1
●Settingmode
ＳＥＴ
1
InP
00
ＳＥＴ
2
ＳＥＴ
3
PuG
1.00
PuS
1.00
PdF
1

dP
0
0
0.0

FU
0
0
 1
2
 3
 4
LoC
0
0
 1
2
 3
SLH
1200
SLL
0

Md
run
run
rdy

Cnt
113
013
PID(RefertoEx.3.)
0：TypeA
1：TypeB
Controloutput1
1：PID
2：ON/OFF
Controloutput2
0：None
1：PID
2：ON/OFF
3：Eventoutput
dIr
0
rdy
Mu1

E1F
00
0：None
1：Deviationhighandlowlimit
2：Deviationhighlimit
3：Deviationlowlimit
4：Deviationhighandlowlimitrange
5：Absolutevaluehighandlowlimit
6：Absolutevaluehighlimit
7：Absolutevaluelowlimit
8：Absolutevaluehighandlowlimitrange
PVEventfunctions
0：None
1：EVoutputhold
2：Stand-bysequence
3：EVoutputhold&stand-bysequence
AdditionalEventfunctions
E1H
00
E1L
0
E1C
0
E1t
0
E1b
00
0：None
1：PVabnormal(sensorbreak)
2：Heaterabnormal
3：PV+Heaterabnormal
Type
0：None
1：Hold(Powerreset)
Action
E1P
0
0
 1
tun
1
1
 2
3
 4
 5
AtG
1.0
AtC
2.0
P1
3.0
I
0
d
0
t1
20
Arw
100.0
MH1
100.0
ML1

Pbb

C1

CP1
0

- 8 -
▲key ▲key ▲key
PV PV Timersettingmode PV
▼key SV ▼key SV Callingdisplay ▼key SV
MODEkey MODEkey MODEkey
PV PV PV
SV SV SV
SV Non-use MODEkey
SV Controloutput
SV Event1output PV
MODEkey SV MODEkey
PV
SV PV
SV Autostart  (ONdelay) SV
SV Manualstart (ONdelay) MODEkey
SV Eventstart (ONdelay)
SV Autostart  (OFFdelay) PV
SV Manualstart(OFFdelay) SV
MODEkey SV Eventstart(OFFdelay) MODEkey
SV SVstart(OFFdelay)
PV MODEkey PV
SV SV
MODEkey PV MODEkey
SV
PV SV Hour/minute PV
SV SV Minute/second SV
MODEkey MODEkey MODEkey
PV PV PV
SV SV SV
MODEkey MODEkey
PV PV
SV SV
MODEkey MODEkey
PV MODEkey PV
SV SV
PV MODEkey(returnto74)
SV
MODEkey
PV
SV
MODEkey MODEkey(returnto67)
PV
SV
SV Normalopen
SV Normalclose
MODEkey(returnto47)
Select9thdisplayon
operationmodeB.
Select5thdisplayon
operationmodeB.
Select6thdisplayon
operationmodeB.
Select7thdisplayon
operationmodeB.
Select8thdisplayon
operationmodeB.
Select1stdisplayon
operationmodeB.
Select2nddisplayon
operationmodeB.
Select3rddisplayon
operationmodeB.
Select4thdisplayon
operationmodeB.
75.Settingfor1stprioritydisplays
＜SET7：Timer＞
67.Timersetting
68.Timeroutputsetting
Selectprioritydisplays
Callingdisplay(RefertoEx.1.)
＜SET4：EventOutput2＞
47.Eventoutput2Setting ＜SET0：PriorityDisplays＞ 74.Prioritydisplayssetting
76.Settingfor2ndprioritydisplays
77.Settingfor3rdprioritydisplays
78.Settingfor4thprioritydisplays
79.Settingfor5thprioritydisplays
80.Settingfor6thprioritydisplays
82.Settingfor8thprioritydisplays
83.Settingfor9thprioritydisplays
81.Settingfor7thprioritydisplays
EV2settingmodeCalling
display
Selectbelowfunctions.
Sethighlimitvalue.
Setlowlimitvalue.
48.FunctionsettingforEV2
49.HighlimitsettingforEV2
50.LowlimitsettingforEV2
Normalopen/closeisselectable
whileeventoutputisON.
54.PolaritysettingforEV2
Thermocouple/R.T.D.(Pt100,J
Pt100)Input
Settingrange:0〜999
0.0〜999.9
Settingunit:℃
Setdelaytimerwhen
required(sec).
Foroutbreakofsensorand
heaterabnormal
71.TimerSVstartpermissiblerange
69.Timeroutputsetting
70.Timerunitselection
51.ControlsensitivitysettingforEV2
52.DelaytimersettingforEV2
53.AbnormalforEV2
Residualtimemonitor.
Timerstartwhenpressing
FUNCkey.
73.Timerresidualtimemonitorsetting
Current/VoltageInput
Settingrange:0〜9999
(Decimalpointat
designatedposition)
Settingunit:digit
Settingrange:0:00〜99:59
0:00〜59:59
72.Timertimesetting
Setsensitivitywhen
required(℃).
ＳＥＴ
4
ＳＥＴ
1
ＳＥＴ
E2F
00
E2H
00
E2L
00
E2C
0
E2t
0
E2b
00
E2P
0
0
 1
ＳＥＴ
7
ＳＥＴ
tMn
0
0
1
2
tMF
1
1
2
3
4
5
6
7
HKn
1
1
2
tSu
0
t1n
0.00
t1A
0.00
ＳＥＴ
1
ＳＥＴ
0
ＳＥＴ
Pr11

Pr12

Pr13

Pr14

Pr15

Pr16

Pr17

Pr18

Pr19

0：None
1：Deviationhighandlowlimit
2：Deviationhighlimit
3：Deviationlowlimit
4：Deviationhighandlowlimitrange
5：Absolutevaluehighandlowlimit
6：Absolutevaluehighlimit
7：Absolutevaluelowlimit
8：Absolutevaluehighandlowlimitrange
PVEventfunctions
0：None
1：EVoutputhold
2：Stand-bysequence
3：EVoutputhold&stand-bysequence
AdditionalEventfunctions
0：None
1：PVabnormal(sensor
break)
2：Heaterabnormal
3
：
PV
+
Heaterabnormal
Type
0：None
1：Hold(Powerreset)
Action

- 9 -
(Display) (Description) (TroubleShooting)
L o C
−−−−
＿＿＿＿
E r r 0
E r r 2
t I M E
At
S u 2
d I
F U n K
Shown whenever input value exceeds
the high limit of display range. Also
display when the wire thermocouple,
ABb-terminal of R.T.D is snapped off.
Check the snapping of thermocouple
and R.T.D. input.
Shown whenever input value exceeds
the low limit of display range. Check short circuit of input lines
between A-B and A-b R.T.D.
Display of memory error. In case this indication shows after
the re-input of power, replace unit if
it persists.
E r r 1
Display of A/D converter error or
incorrect sensor connection with
selectable input.
Ditto
Display of auto-tuning error.
Display when parameter is changed
in key-lock condition.
Check sensor connection or
change to other tuning.
Discontinue to change parameter.
Alternately this SV/PV display are
shown. Normality
Display when setting value is
changed on SV2 control.
Display when changing setting value
of shift on DI.
Discontinue to change setting value
(during control of SV2 )
Discontinue to change setting value
of the self on digital input
Display when making setting value
change in control display while
function key is on RUN/READY.
Display when altering setting value
in control display while being on
timer.
Discontinue to change setting value
Discontinue to change setting value
of the self on digital input