MITOS VT6 User manual

MITOS VT6 CONTROL MODES
Several control modes can be selected. MITOS VT6 can
be used to start/stop the motor, change its direction,
modifyits speed, or else, simplyused as a remote
display with no inverter control capability. Refer to
following table for selecting MITOS VT6 control mode
depending on inverter model:
Model
VF-NC3
VF-S15
VF-AS3
Control mode
Cmod =2
Fmod ≠3
Cmod =2
Fmod ≠4
Cmod = 4
Fmod ≠21, 22
Frequency
mode
Cmod ≠2
Fmod =3
Cmod ≠2
Fmod =4
Cmod ≠ 3, 4
Fmod = 22
Control +
Frequency
mode
Cmod =2
Fmod =3
Cmod =2
Fmod =4
Cmod = 4
Fmod = 22
On VF-NC3 e VF-S15, set F802=1 and F829=1
On VF-AS3, set F802=1 and F827=1
CONFIGURATION MENU
Bypressingthesekeystogetherat
startup,theVT6configuration
menuisentered.
MENU CHOICES
Use arrow keys to move inside the Menu. Use the FWD
and REV keys to make the selections and
STOP/RESET keyto exit the configuration menu.
With this menu is possible to select and monitor:
▪Enabling of FWD and REV keys: Use the
FWD/REV keyto enable or disable one or both
keys.
▪Transparent mode: VT6 just used as display
▪Reset Frequency: if ON and frequencycontrol
mode by VT6 is selected then the Set frequency
is not automatically stored and every time
inverter is OFF the frequency value is reset. If
OFF, the last set frequency is always stored.
▪Select language (English, Italian, Spanish,
German, Russian)
▪Unit Selection of standard display suffix (select
between Hz, RPM, m/min, m/sec ---- “none”)
▪C Parameter: The scaling factor of the output
frequency(Freq.) shown on MITOS(0-200)
▪Indication of Software release
MITOS VT6 MONITOR
This is the standard
monitor display for
VT6.
If inverter is in RUN mode (motor running) the standard
monitor display will show an animated arrow () on the
top right-hand corner. The arrow will turn CW if the
inverter receives a RUN FWD command and will turn
CCW if the inverter receives a RUN REV command.
By pressing MON key the second line item can be
changed between several variables:
output frequency, reference frequency, output
current, input voltage, output voltage, last 4
alarms, total working time.
In “standard monitor display”, if the VT6 is in
frequency control mode and transparent mode is not
active, the inverter output frequency can be changed
directly by pressing:
▪Multilanguage capability
▪RS485 and TTY selectable interface
▪Customizable front layout
▪aSuitable for inverter control nd
monitoring
Toshiba -inverters
Advancedcontrolpanelfor
VT6 rev.4.0

SAFETY INFORMATIONS
CONNECTION
Connection type can be selected byswitches on the
back of the MITOS VT6 as shown below:
RS485 TTL
55
31
36
External dimensions are exactly same of MITOS of
the previous model VT5.
Run motor in
forward
direction if
VT6 control
is selected.
Run motor in
reverse
direction if
VT6 control
is selected.
Change inverter
frequency if VT6
freq. control is
selected and scroll
items in monitor
mode
Enter
Monitor
function
Stop motor if
VT6 control
is selected.
Reset
inverters
alarms in all
mode
ON
1 2
VF-NC3
VF-S15
VF-MB1
VF-FS1
VF-AS3
VF-PS1
VF-AS1
VF-S11
ON
1 2
56 mm
107 mm
PANEL CUT DIMENSIONS
FUNCTIONS OF KEYS
120 mm
65 mm
OUTLINE DRAWING
Mandatory
Please read this instruction manual before
starting connection and operation of MITOS-
VT6
Warning
Please always give this manual to the end user
of the MITOS-VT6 panel.
Danger
Every time that a command is transferred from
MITOS-VT6 panel to the Inverter, it is
automatically stored into Inverter memory. If the
connection cable between MITOS and Inverter
is damaged, it will be impossible to keep the
Inverter control (and stop the motor too).
ALWAYS use safety devices to STOP the motor
in emergency conditions
General Cautions
MITOS-VT6 keypad can’t be used in any device
that could create danger to the human body or
from which malfunction or incorrect operation
would present direct threat to human life.
MITOS-VT6 keypad has been manufactured
under strict quality controls. however, if it is
used in critical equipment, where an error or a
malfunction would cause serious accidents to
persons or to the machine, safety devices
MUST be installed on the equipment.
This manual could be subject to modifications
without prior notice.
VF-PS1, VF-AS3.
VF-NC3, VF-S11, VF-S15, VF-MB1, VF-FS1, VF-AS1,
TOSHIBA:
MITOS VT6 can be connected to following Inverters
COMPATIBILITY
“pin to pin” cable.
Connection is made through standard 8 pin RJ45
TOSHIBA: