Mitsubishi Electric CITY MULTI PURY-HP72TNU-A Product guide

AIR CONDITIONING SYSTEMS
MODEL
PURY-HP72-240T(S)NU-A
PURY-HP72-240Y(S)NU-A

MEES19K180
GENERAL LINE-UP GENERAL LINE-UP
I.GENERAL LINE-UP
96K
PURY-HP96YNU-A
120K
PURY-HP120YNU-A
72K
PURY-HP72YNU-A
Type(BTU/h)
Model Name
96K
PURY-HP96TNU-A
120K
PURY-HP120TNU-A
72K
PURY-HP72TNU-A
Type(BTU/h)
Model Name
192K
PURY-HP192YSNU-A
240K
PURY-HP240YSNU-A
144K
PURY-HP144YSNU-A
Type(BTU/h)
Model Name
192K
PURY-HP192TSNU-A
240K
PURY-HP240TSNU-A
144K
PURY-HP144TSNU-A
Type(BTU/h)
Model Name
Hyper Heating Inverter R2-Series-208-230V Hyper Heating Inverter R2-Series-460V
body1.fm 1 ページ ２０２０年２月２５日 火曜日 午後４時２８分

PURY-HP-T(S)NU-A, PURY-HP-Y(S)NU-A
MEES19K180 1
CONTENTS Hyper Heating Inverter R2-Series
I.Hyper Heati ng Inverter R2 -Series
1. SPECIFICATIONS .................................................................................................................................... 2
2. EXTERNAL DIMENSIONS ....................................................................................................................... 14
3. CENTER OF GRAVITY ............................................................................................................................ 20
4. ELECTRICAL WIRING DIAGRAMS ......................................................................................................... 21
5. SOUND LEVELS ...................................................................................................................................... 23
5-1. Sound levels in cooling mode .......................................................................................................... 23
5-2. Sound levels in heating mode.......................................................................................................... 25
6. VIBRATION LEVEL .................................................................................................................................. 27
7. OPERATION TEMPERATURE RANGE...................................................................................................28
8. CAPACITY TABLES ................................................................................................................................. 29
8-1. Selection of Cooling/Heating Units .................................................................................................. 30
8-2. Correction by temperature ............................................................................................................... 40
8-3. Correction by total indoor................................................................................................................. 64
8-4. Correction by refrigerant piping length............................................................................................. 67
8-5. Correction at frost and defrost ......................................................................................................... 70
8-6. Correction at evaporation-temperature (ET) control ........................................................................ 70
9. OPTIONAL PARTS................................................................................................................................... 71
9-1. JOINT and REDUCER..................................................................................................................... 71
9-2. OUTDOOR TWINNING KIT............................................................................................................. 75
9-3. JOINT KIT "CMY-R160-J1" FOR BC CONTROLLER ..................................................................... 76
10.ELECTRICAL WORK ............................................................................................................................... 77
10-1.General cautions ............................................................................................................................. 77
10-2.Power supply for Outdoor unit ......................................................................................................... 78
10-3.Power cable specifications .............................................................................................................. 79
10-4.Power supply examples................................................................................................................... 80
11.M-NET CONTROL ................................................................................................................................... 82
11-1.Transmission cable length limitation................................................................................................ 82
11-2.Transmission cable specifications ................................................................................................... 83
11-3.System configuration restrictions..................................................................................................... 84
11-4.Address setting................................................................................................................................ 88
12.PIPING DESIGN ...................................................................................................................................... 100
12-1.R410A Piping material..................................................................................................................... 101
12-2.Piping Design .................................................................................................................................. 103
12-3.Refrigerant charging calculation ...................................................................................................... 110
12-4.Compatibility .................................................................................................................................... 114
13.OUTDOOR INSTALLATION .................................................................................................................... 115
13-1.General requirements for installation............................................................................................... 115
13-2.Spacing............................................................................................................................................ 116
13-3.Piping direction ................................................................................................................................ 118
13-4.Weather countermeasure ................................................................................................................ 123
13-5.Countermeasure to wind ................................................................................................................. 123
0000005744.BOOK 1 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
2
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
I.Hyper Heating Inverter R2-Series1. SPECIFICATIONS
Outdoor Model PURY-HP72TNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 72,000
(Nominal) kW 21.1
Power input kW 5.22
(208-230) Current input A 16.0-14.5
(Rated) BTU/h 69,000
kW 20.2
Power input kW 4.74 4.91
(208-230) Current input A 14.6-13.2 15.1-13.6
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 80,000
(Nominal) kW 23.4
Power input kW 5.66
(208-230) Current input A 17.4-15.7
(Rated) BTU/h 76,000
kW 22.3
Power input kW 5.12 5.36
(208-230) Current input A 15.7-14.2 16.5-14.9
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~18
Sound pressure level (measured in anechoic room) *3 dB <A> 56.5/58.0
Sound power level (measured in anechoic room) *3 dB <A> 75.5/77.0
Refrigerant High pressure in. (mm) 5/8 (15.88) Brazed
piping diameter Low pressure in. (mm) 3/4 (19.05) Brazed
Minimum Circuit Ampacity A 38-35
Maximum Overcurrent Protection A 60-50
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 7,400
m3/min 210
L/s 3,500
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 4.0
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 17 lbs + 10 oz (8.0 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 609 (276)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GY
Wiring KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-R160-J1,CMY-R201,202,301,306S-G,CMY-R302,303,304,305S-G1
BC controller: CMB-P104,106,108,1012,1016NU-J1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 2 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
3
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP96TNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 96,000
(Nominal) kW 28.1
Power input kW 6.50
(208-230) Current input A 20.0-18.1
(Rated) BTU/h 92,000
kW 27.0
Power input kW 5.80 6.23
(208-230) Current input A 17.8-16.1 19.2-17.3
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 108,000
(Nominal) kW 31.7
Power input kW 7.58
(208-230) Current input A 23.3-21.1
(Rated) BTU/h 103,000
kW 30.2
Power input kW 6.93 7.10
(208-230) Current input A 21.3-19.3 21.8-19.8
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~24
Sound pressure level (measured in anechoic room) dB <A> 58.5/60.0
Sound power level (measured in anechoic room) *3 dB <A> 77.5/79.0
Refrigerant High pressure in. (mm) 3/4 (19.05) Brazed
piping diameter Low pressure in. (mm) 7/8 (22.2) Brazed
Minimum Circuit Ampacity A 44-40
Maximum Overcurrent Protection A 70-60
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 8,300
m3/min 235
L/s 3,920
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 5.6
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 662 (300)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GY
Wiring KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-R160-J1,CMY-R201,202,203,301,306S-G,CMY-R302,303,304,305S-G1
BC controller: CMB-P104,106,108,1012,1016NU-J1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 3 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
4
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP120TNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 120,000
(Nominal) kW 35.2
Power input kW 8.82
(208-230) Current input A 27.2-24.6
(Rated) BTU/h 114,000
kW 33.4
Power input kW 8.04 8.29
(208-230) Current input A 24.7-22.4 25.5-23.1
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 135,000
(Nominal) kW 39.6
Power input kW 10.07
(208-230) Current input A 31.0-28.0
(Rated) BTU/h 129,000
kW 37.8
Power input kW 9.01 9.63
(208-230) Current input A 27.7-25.1 29.7-26.8
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~30
Sound pressure level (measured in anechoic room) *3 dB <A> 64.0/65.0
Sound power level (measured in anechoic room) *3 dB <A> 84.0/85.0
Refrigerant High pressure in. (mm) 3/4 (19.05) Brazed
piping diameter Low pressure in. (mm) 1-1/8 (28.58) Brazed
Minimum Circuit Ampacity A 47-44
Maximum Overcurrent Protection A 70-60
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 9,550
m3/min 270
L/s 4,500
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 7.8
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 662 (300)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GY
Wiring KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-R160-J1,CMY-R201,202,203,301,306S-G,CMY-R302,303,304,305S-G1
BC controller: CMB-P104,106,108,1012,1016NU-J1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 4 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
5
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP144TSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 144,000
(Nominal) kW 42.2
Power input kW 11.92
(208-230) Current input A 36.7-33.2
(Rated) BTU/h 138,000
kW 40.4
Power input kW 10.73 11.34
(208-230) Current input A 33.0-29.9 34.9-31.6
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 160,000
(Nominal) kW 46.9
Power input kW 12.50
(208-230) Current input A 38.5-34.8
(Rated) BTU/h 152,000
kW 44.5
Power input kW 11.22 11.91
(208-230) Current input A 34.6-31.2 36.7-33.2
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~36
Sound pressure level (measured in anechoic room) *3 dB <A> 59.5/61.0
Sound power level (measured in anechoic room) *3 dB <A> 78.5/80.0
Refrigerant High pressure in. (mm) 7/8 (22.2) Brazed
piping diameter Low pressure in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PURY-HP72TNU-A PURY-HP72TNU-A
Minimum Circuit Ampacity A 38-35 38-35
Maximum Overcurrent Protection A 60-50 60-50
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 7,400 7,400
m3/min 210 210
L/s 3,500 3,500
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter Inverter
Motor output kW 4.0 4.0
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1> <MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 17 lbs + 10 oz (8.0 kg) R410A x 17 lbs + 10 oz (8.0 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 609 (276) 609 (276)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) - -
Pipe between unit and High pressure in. (mm) 5/8 (15.88) Brazed 5/8 (15.88) Brazed
distributor Low pressure in. (mm) 3/4 (19.05) Brazed 3/4 (19.05) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GZ
Wiring KE94G811 KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-R100NCBK
joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-R160-J1,CMY-R201,202,203,204,306S-G,CMY-R302,303,304,305S-G1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 5 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
6
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP192TSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 192,000
(Nominal) kW 56.3
Power input kW 14.53
(208-230) Current input A 44.8-40.5
(Rated) BTU/h 184,000
kW 53.9
Power input kW 13.00 13.89
(208-230) Current input A 40.0-36.2 42.8-38.7
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 215,000
(Nominal) kW 63.0
Power input kW 16.49
(208-230) Current input A 50.8-45.9
(Rated) BTU/h 206,000
kW 60.4
Power input kW 15.04 15.49
(208-230) Current input A 46.3-41.9 47.7-43.2
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~48
Sound pressure level (measured in anechoic room) *3 dB <A> 61.5/63.0
Sound power level (measured in anechoic room) *3 dB <A> 80.5/82.0
Refrigerant High pressure in. (mm) 7/8 (22.2) Brazed
piping diameter Low pressure in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PURY-HP96TNU-A PURY-HP96TNU-A
Minimum Circuit Ampacity A 44-40 44-40
Maximum Overcurrent Protection A 70-60 70-60
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 8,300 8,300
m3/min 235 235
L/s 3,920 3,920
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter Inverter
Motor output kW 5.6 5.6
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1> <MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg) R410A x 23 lbs + 12 oz (10.8 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 662 (300) 662 (300)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) - -
Pipe between unit and High pressure in. (mm) 3/4 (19.05) Brazed 3/4 (19.05) Brazed
distributor Low pressure in. (mm) 7/8 (22.2) Brazed 7/8 (22.2) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GZ
Wiring KE94G811 KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-R200NCBK
joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-Y202S-G2,CMY-R160-J1,CMY-R201,202,203,204,306S-G,
CMY-R302,303,304,305S-G1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 6 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
7
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP240TSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 208-230 V ±10% 60 Hz
Cooling capacity *1 BTU/h 240,000
(Nominal) kW 70.3
Power input kW 20.08
(208-230) Current input A 61.9-56.0
(Rated) BTU/h 228,000
kW 66.8
Power input kW 18.72 18.45
(208-230) Current input A 57.7-52.2 56.9-51.4
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 270,000
(Nominal) kW 79.1
Power input kW 22.45
(208-230) Current input A 69.2-62.6
(Rated) BTU/h 258,000
kW 75.6
Power input kW 20.64 20.92
(208-230) Current input A 63.6-57.5 64.5-58.3
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/2~50
Sound pressure level (measured in anechoic room) *3 dB <A> 67.0/68.0
Sound power level (measured in anechoic room) *3 dB <A> 87.0/88.0
Refrigerant High pressure in. (mm) 7/8 (22.2) Brazed (1-1/8 (28.58) Brazed for the part that exceeds 65 m)
piping diameter Low pressure in. (mm) 1-3/8 (34.93) Brazed
Set Model
Model PURY-HP120TNU-A PURY-HP120TNU-A
Minimum Circuit Ampacity A 47-44 47-44
Maximum Overcurrent Protection A 70-60 70-60
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 9,550 9,550
m3/min 270 270
L/s 4,500 4,500
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter Inverter
Motor output kW 7.8 7.8
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1> <MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg) R410A x 23 lbs + 12 oz (10.8 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 662 (300) 662 (300)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) - -
Pipe between unit and High pressure in. (mm) 3/4 (19.05) Brazed 3/4 (19.05) Brazed
distributor Low pressure in. (mm) 1-1/8 (28.58) Brazed 1-1/8 (28.58) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0GZ
Wiring KE94G811 KE94G811
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-R200NCBK
joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-Y202S-G2,CMY-R160-J1,CMY-R201,202,203,204,205,306S-G,
CMY-R302,303,304,305S-G1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 7 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
8
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP72YNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 72,000
(Nominal) kW 21.1
Power input kW 5.22
(460) Current input A 7.2
(Rated) BTU/h 69,000
kW 20.2
Power input kW 4.74 4.91
(460) Current input A 6.6 6.8
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 80,000
(Nominal) kW 23.4
Power input kW 5.66
(460) Current input A 7.8
(Rated) BTU/h 76,000
kW 22.3
Power input kW 5.12 5.36
(460) Current input A 7.1 7.4
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~18
Sound pressure level (measured in anechoic room) *3 dB <A> 56.5/58.0
Sound power level (measured in anechoic room) *3 dB <A> 75.5/77.0
Refrigerant High pressure in. (mm) 5/8 (15.88) Brazed
piping diameter Low pressure in. (mm) 3/4 (19.05) Brazed
Minimum Circuit Ampacity A 17
Maximum Overcurrent Protection A 25
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 7,400
m3/min 210
L/s 3,500
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 4.0
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 17 lbs + 10 oz (8.0 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 644 (292)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0H0
Wiring KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-R160-J1,CMY-R201,202,301,306S-G,CMY-R302,303,304,305S-G1
BC controller: CMB-P104,106,108,1012,1016NU-J1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 8 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
9
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP96YNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 96,000
(Nominal) kW 28.1
Power input kW 6.50
(460) Current input A 9.0
(Rated) BTU/h 92,000
kW 27.0
Power input kW 5.80 6.23
(460) Current input A 8.0 8.6
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 108,000
(Nominal) kW 31.7
Power input kW 7.58
(460) Current input A 10.5
(Rated) BTU/h 103,000
kW 30.2
Power input kW 6.93 7.10
(460) Current input A 9.6 9.9
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~24
Sound pressure level (measured in anechoic room) *3 dB <A> 58.5/60.0
Sound power level (measured in anechoic room) *3 dB <A> 77.5/79.0
Refrigerant High pressure in. (mm) 3/4 (19.05) Brazed
piping diameter Low pressure in. (mm) 7/8 (22.2) Brazed
Minimum Circuit Ampacity A 20
Maximum Overcurrent Protection A 30
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 8,300
m3/min 235
L/s 3,920
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 5.6
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 697 (316)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0H0
Wiring KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-R160-J1,CMY-R201,202,203,301,306S-G,CMY-R302,303,304,305S-G1
BC controller: CMB-P104,106,108,1012,1016NU-J1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 9 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
10
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP120YNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 120,000
(Nominal) kW 35.2
Power input kW 8.82
(460) Current input A 12.3
(Rated) BTU/h 114,000
kW 33.4
Power input kW 8.04 8.29
(460) Current input A 11.2 11.5
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 135,000
(Nominal) kW 39.6
Power input kW 10.07
(460) Current input A 14.0
(Rated) BTU/h 129,000
kW 37.8
Power input kW 9.01 9.63
(460) Current input A 12.5 13.4
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~30
Sound pressure level (measured in anechoic room) *3 dB <A> 64.0/65.0
Sound power level (measured in anechoic room) *3 dB <A> 84.0/85.0
Refrigerant High pressure in. (mm) 3/4 (19.05) Brazed
piping diameter Low pressure in. (mm) 1-1/8 (28.58) Brazed
Minimum Circuit Ampacity A 21
Maximum Overcurrent Protection A 35
FAN Type x Quantity Propeller fan x 2
Airflow rate cfm 9,550
m3/min 270
L/s 4,500
Control, Driving mechanism Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46
*4 External static press. 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter
Motor output kW 7.8
Case heater kW -
Lubricant MEL46
External finish Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601 psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection
Fan motor -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 697 (316)
Heat exchanger Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) -
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0H0
Wiring KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-R160-J1,CMY-R201,202,203,301,306S-G,CMY-R302,303,304,305S-G1
BC controller: CMB-P104,106,108,1012,1016NU-J1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 10 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
11
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP144YSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 144,000
(Nominal) kW 42.2
Power input kW 11.92
(460) Current input A 16.6
(Rated) BTU/h 138,000
kW 40.4
Power input kW 10.73 11.34
(460) Current input A 14.9 15.8
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 160,000
(Nominal) kW 46.9
Power input kW 12.50
(460) Current input A 17.4
(Rated) BTU/h 152,000
kW 44.5
Power input kW 11.22 11.91
(460) Current input A 15.6 16.6
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~36
Sound pressure level (measured in anechoic room) *3 dB <A> 59.5/61.0
Sound power level (measured in anechoic room) *3 dB <A> 78.5/80.0
Refrigerant High pressure in. (mm) 7/8 (22.2) Brazed
piping diameter Low pressure in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PURY-HP72YNU-A PURY-HP72YNU-A
Minimum Circuit Ampacity A 17 17
Maximum Overcurrent Protection A 25 25
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 7,400 7,400
m3/min 210 210
L/s 3,500 3,500
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter Inverter
Motor output kW 4.0 4.0
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1> <MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 17 lbs + 10 oz (8.0 kg) R410A x 17 lbs + 10 oz (8.0 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 644 (292) 644 (292)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) - -
Pipe between unit and High pressure in. (mm) 5/8 (15.88) Brazed 5/8 (15.88) Brazed
distributor Low pressure in. (mm) 3/4 (19.05) Brazed 3/4 (19.05) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0H1
Wiring KE94G817 KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-R100NCBK
joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-R160-J1,CMY-R201,202,203,204,306S-G,CMY-R302,303,304,305S-G1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 11 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
12
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP192YSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 192,000
(Nominal) kW 56.3
Power input kW 14.53
(460) Current input A 20.2
(Rated) BTU/h 184,000
kW 53.9
Power input kW 13.00 13.89
(460) Current input A 18.1 19.3
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 215,000
(Nominal) kW 63.0
Power input kW 16.49
(460) Current input A 22.9
(Rated) BTU/h 206,000
kW 60.4
Power input kW 15.04 15.49
(460) Current input A 20.9 21.6
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/1~48
Sound pressure level (measured in anechoic room) *3 dB <A> 61.5/63.0
Sound power level (measured in anechoic room) *3 dB <A> 80.5/82.0
Refrigerant High pressure in. (mm) 7/8 (22.2) Brazed
piping diameter Low pressure in. (mm) 1-1/8 (28.58) Brazed
Set Model
Model PURY-HP96YNU-A PURY-HP96YNU-A
Minimum Circuit Ampacity A 20 20
Maximum Overcurrent Protection A 30 30
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 8,300 8,300
m3/min 235 235
L/s 3,920 3,920
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter Inverter
Motor output kW 5.6 5.6
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1> <MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg) R410A x 23 lbs + 12 oz (10.8 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 697 (316) 697 (316)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) - -
Pipe between unit and High pressure in. (mm) 3/4 (19.05) Brazed 3/4 (19.05) Brazed
distributor Low pressure in. (mm) 7/8 (22.2) Brazed 7/8 (22.2) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0H1
Wiring KE94G817 KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-R200NCBK
joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-Y202S-G2,CMY-R160-J1,CMY-R201,202,203,204,306S-G,
CMY-R302,303,304,305S-G1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 12 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
13
1. SPECIFICATIONS Hyper Heating Inverter R2-Series
Outdoor Model PURY-HP240YSNU-A
Indoor Model Non-Ducted Ducted
Power source 3-phase 3-wire 460 V ±10% 60 Hz
Cooling capacity *1 BTU/h 240,000
(Nominal) kW 70.3
Power input kW 20.08
(460) Current input A 28.0
(Rated) BTU/h 228,000
kW 66.8
Power input kW 18.72 18.45
(460) Current input A 26.1 25.7
Temp. range of Indoor W.B. 59~75°F (15~24°C)
cooling Outdoor D.B. 23~126°F (-5~52°C)
Heating capacity *2 BTU/h 270,000
(Nominal) kW 79.1
Power input kW 22.45
(460) Current input A 31.3
(Rated) BTU/h 258,000
kW 75.6
Power input kW 20.64 20.92
(460) Current input A 28.7 29.1
Temp. range of Indoor D.B. 59~81°F (15~27°C)
heating Outdoor W.B. -22~60°F (-30~15.5°C)
Indoor unit Total capacity 50~150% of outdoor unit capacity
connectable Model/Quantity P04~P96/2~50
Sound pressure level (measured in anechoic room) *3 dB <A> 67.0/68.0
Sound power level (measured in anechoic room) *3 dB <A> 87.0/88.0
Refrigerant High pressure in. (mm) 7/8 (22.2) Brazed (1-1/8 (28.58) Brazed for the part that exceeds 65 m)
piping diameter Low pressure in. (mm) 1-3/8 (34.93) Brazed
Set Model
Model PURY-HP120YNU-A PURY-HP120YNU-A
Minimum Circuit Ampacity A 21 21
Maximum Overcurrent Protection A 35 35
FAN Type x Quantity Propeller fan x 2 Propeller fan x 2
Airflow rate cfm 9,550 9,550
m3/min 270 270
L/s 4,500 4,500
Control, Driving mechanism Inverter-control, Brushless DC motor Inverter-control, Brushless DC motor
Motor output kW 0.46+0.46 0.46+0.46
*4 External static press. 0 in.WG (0 Pa) 0 in.WG (0 Pa)
Compressor Type x Quantity Inverter scroll hermetic compressor x 1 Inverter scroll hermetic compressor x 1
Manufacture AC&R Works, MITSUBISHI ELECTRIC CORPORATION AC&R Works, MITSUBISHI ELECTRIC CORPORATION
Starting method Inverter Inverter
Motor output kW 7.8 7.8
Case heater kW - -
Lubricant MEL46 MEL46
External finish Pre-coated galvanized steel sheet Pre-coated galvanized steel sheet
<MUNSELL 5Y 8/1> <MUNSELL 5Y 8/1>
External dimension H x W x D in. 71-5/8 x 49-1/4 x 29-3/8 71-5/8 x 49-1/4 x 29-3/8
mm 1,818 x 1,250 x 745 1,818 x 1,250 x 745
Protection High pressure protection High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
High pressure sensor, High pressure switch at 4.15 MPa (601
psi)
devices Inverter circuit (COMP./FAN) Over-heat protection, Over-current protection Over-heat protection, Over-current protection
Fan motor - -
Refrigerant Type x original charge R410A x 23 lbs + 12 oz (10.8 kg) R410A x 23 lbs + 12 oz (10.8 kg)
Control Indoor LEV and BC controller
Net weight lbs (kg) 697 (316) 697 (316)
Heat exchanger Salt-resistant cross fin & copper tube Salt-resistant cross fin & copper tube
HIC circuit (HIC: Heat Inter-Changer) - -
Pipe between unit and High pressure in. (mm) 3/4 (19.05) Brazed 3/4 (19.05) Brazed
distributor Low pressure in. (mm) 1-1/8 (28.58) Brazed 1-1/8 (28.58) Brazed
Defrosting method Auto-defrost mode (Reversed refrigerant cycle)
Drawing External KB94C0H1
Wiring KE94G817 KE94G817
Standard Document Installation Manual
attachment Accessory Details refer to External Drw
Optional parts Outdoor Twinning kit: CMY-R200NCBK
joint: CMY-Y102SS-G2,CMY-Y102LS-G2,CMY-Y202S-G2,CMY-R160-J1,CMY-R201,202,203,204,205,306S-G,
CMY-R302,303,304,305S-G1
Main BC controller: CMB-P108,1012,1016NU-JA1,CMB-P1016NU-KA1
Sub BC controller: CMB-P104,108NU-KB1
Remarks Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred
to the Installation Manual.
Notes: Unit converter
1.Nominal cooling conditions (Test conditions are based on AHRI 1230)
Indoor: 80°FD.B./67°FW.B. (26.7°CD.B./19.4°CW.B.), Outdoor: 95°FD.B. (35°CD.B.)
2.Nominal heating conditions (Test conditions are based on AHRI 1230)
Indoor: 70°FD.B. (21.1°CD.B.), Outdoor: 47°FD.B./43°FW.B. (8.3°CD.B./6.1°CW.B.)
3.Cooling mode/Heating mode
4.External static pressure option is available (0.12 in.WG, 0.24 in.WG, 0.32 in.WG/30 Pa, 60 Pa, 80 Pa).
BTU/h =kW x 3,412
cfm =m3/min x 35.31
lbs =kg/0.4536
*Above specification data is
* Due to continuing improvement, above specifications may be subject to change without notice. subject to rounding variation.
0000005744.BOOK 13 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
14
2. EXTERNAL DIMENSIONS Hyper Heating Inverter R2-Series
2. EXTERNAL DIMENSIONS
PURY-HP72, 96, 120TNU-A
Unit: mm (in.)
1 2 4 3 5 6 7 8
NO.
740(29-3/16)
70(2-13/16)
150(5-15/16)
85(3-3/8)
85(3-3/8)
130(5-1/8)
150
18(3/4)1204(47-7/16)
18
1240(48-7/8)
110(4-3/8)
(740)(29-3/16)
185(7-5/16)
29.5
681(678~684)
29.5
94 79
181
160(6-5/16) 243(9-5/8)
150
128(5-1/16)
125
132(5-1/4)
207(8-3/16) 256(10-1/8)
109
129(5-1/8)
84(3-5/16)
90(3-9/16)
54(2-3/16)
135(5-3/8)
20(13/16)
54
592(23-5/16)54(2-3/16)
20(13/16)
148(5-7/8)
152(6)
216(8-9/16)
166
144(5-11/16)
303
1515(59-11/16)
1818(71-5/8)
90(3-9/16)
1060(41-3/4)
90(3-9/16)
172(6-13/16)
(3-3/4) (3-1/8)
(5-15/16)
(6-9/16)
(7-3/16)
(26-13/16)(26-3/4~26-15/16)
(1-3/16)
(11-15/16)
(4-5/16)
(4-15/16)(2-3/16)
(3/4)
(5-15/16)
(1-3/16)
745(29-3/8)
(745)(29-3/8)
1250(49-1/4)
(5)
(1/4)
(5)(1/4)
(5)
(1/4)
2
5
6
8
(Mounting pitch)
Bottom view
(Mounting pitch)
2×2-14(9/16)×20(13/16) Oval hole
1
Control box
3
4
7
Service panel
Intake
air
Intake
air
Discharge air
Intake
air
Intake
air
2×6-ø4.6(3/16) Hole (Make hole at the plastic fan guard
for snow hood attachment)
<Snow hood attachment hole>
Top view
Front view
Left side view
Rear view
Refrigerant service valve <Low pressure> Refrigerant service valve <High pressure>
Note 1. Please refer to the next page for information regarding necessary
spacing around the unit and foundation work.
2. At brazing of pipes, wrap the refrigerant service valve
with wet cloth and keep the temperature of refrigerant service valve under 120°C(248°F).
For transmission cables
For wires
For pipes
Usage Specifications
Front through hole Bottom through hole
Front through hole Front through hole
Bottom through hole Bottom through hole
Front through hole
148(5-7/8) × 84(3-5/16) Knockout hole
ø62.7(2-1/2) or ø34.5(1-3/8) Knockout hole ø43.7(1-3/4) or ø22.2(7/8) Knockout hole ø65(2-9/16) Knockout hole ø52(2-1/16) Knockout hole ø34(1-3/8) Knockout hole
150(5-15/16) × 94(3-3/4) Knockout hole
ø34(1-3/8) Knockout hole
Bottom through hole
Connecting pipe specifications
*1 Connect the refrigerant pipe to the service valve
according to the Installation Manual.
Model
Diameter
Refrigerant pipe Service valve
HP96
ø28.58(1-1/8)
ø19.05(3/4) Brazed *1
ø28.58(1-1/8)
HP72
High pressure Low pressure
ø28.58(1-1/8) Brazed ø22.2(7/8) Brazed *1
HP120
High pressure Low pressure
ø19.05(3/4) Brazed *1ø15.88(5/8) Brazed *1
0000005744.BOOK 14 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
15
2. EXTERNAL DIMENSIONS Hyper Heating Inverter R2-Series
PURY-HP72, 96, 120TNU-A
Unit: mm (in.)
1.Required space around the unit 2.Foundation work
Front Front
<Top view>
<Unit:mm(in)>
<Top view>
<To be left open>
Front
Wall <H>
<To be left open>
Front
<Unit:mm(in)>
Wall <H>
<To be left open>
<To be left open>
<To be left open>
Front
Wall <H>
Wall <H>
Wall <H>
Wall <H>
Front
Front
<To be left open>
Wall <H>
Front
Wall <H>
<To be left open>
<To be left open>
Front
Front
Front
Wall <H>
Wall <H>
Front
<To be left open>
<To be left open>
<Wall height limit> Front :Up to the unit height
Back :Up to the unit height Side :Up to the unit height
M10 anchor bolt
<field supply required>
Fixing plate
<field supply required>
Fig.A
<Side view>
Front
Fig.B
●In case of single installation
1 Secure enough space around the unit as shown in the figure below.
· With a space of at least
2 When the height of the walls on the front, back or on the sides<H>
exceeds the wall height limit as defined below add the height that exceeds the height limit <h> to the figures that are marked with an asterisk.
1 Take into consideration the surface strength, water drainage route,
piping route, and wiring route when preparing the installation site. <Note that the drain water comes out of the unit during operation.>
2 Build the foundation in such way that the corner of the installation leg is
securely supported as shown in the right figure.(Fig.A) When using a rubber isolating cushion, please ensure it is large enough to cover the entire width of each of the unit's legs.
3 The protrusion length of the anchor bolt must not exceed 30mm(1-3/16).(Fig.A) 4 Use four fixing plates as shown in the right figure <field supply required>
when using post-installed anchor bolts.(Fig.B)
5 To prevent small animals and water and snow from entering the unit and damaging its parts,
close the gap around the edges of through holes for pipes and wires with filler plates <field supply required>.
6 When the pipes or cables are routed at the bottom of the unit,
make sure that the through hole at the base of the unit does not get blocked with the installation base.
7 Refer to the Installation Manual when installing units on an installation base.
●In case of collective installation
1 When multiple units are installed adjacent to each other, secure enough space to allow
for air circulation and walkway between groups of units as shown in the figures below.
2 At least two sides must be left open. 3 As with the single installation, add the height that exceeds the height limit<h>
to the figures that are marked with an asterisk.
4 If there is a wall at both the front and the rear of the unit, install up to six units
consecutively in the side direction and provide a space of 1000mm(39-3/8) or more as inlet space/ passage space for each six units.
450mm(17-3/4) to the wall on the back of the unit
· With a space of at least
300mm(11-13/16) to the wall on the back of the unit
30 min.* 450 min.* 450 min.*
300 min.*450 min.*
450 min.*
450 min.
30 min. 450 min.450 min.* 450 min. 300 min.*
450 min.* 300 min.*
450 min.*
1000 min.*
900 min. 450 min.*
900 min. 450 min.*450 min.*
30 min.*
450 min.450 min.
450 min.* 450 min.*
30 min.*
(1-3/16) (1-3/16)
(17-3/4) (17-3/4)
(17-3/4) (17-3/4)
(17-3/4) (11-13/16)
(17-3/4) (17-3/4)
(1-3/16)
(17-3/4) (17-3/4)
(1-3/16)
(39-3/8)
(17-3/4) (35-7/16) (17-3/4)
(17-3/4)
(17-3/4) (11-13/16)
(17-3/4) (17-3/4) (17-3/4) (11-13/16)
(35-7/16)
(17-3/4)
30mm max.
Unit height h
H
Unit height h
H
(1-3/16)
0000005744.BOOK 15 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
16
2. EXTERNAL DIMENSIONS Hyper Heating Inverter R2-Series
PURY-HP144, 192, 240TSNU-A
Unit: mm (in.)
Outdoor unit 2
Front view
Outdoor unit 1
Intake
air
Discharge air
c
b
To BC controller
a
Twinning pipe(High pressure) <optional parts>
e
To BC controller
Twinning pipe(Low pressure) <optional parts>
df
Left view
Intake
air
Intake
air
Intake
air
Note 1. Connect the pipes as shown in the figure above. Refer to the table above for the pipe size.
2. Twinning pipes should not be tilted more than 15 degrees from the horizontal plane.
Be sure to see the Installation Manual for details of Twinning pipe installation.
3. The pipe section before the Twinning pipe (section ″a″and ″b″in the figure) must have at least 500mm(19-11/16) of straight section
(*including the straight pipe that is supplied with the Twinning pipe).
4. Only use the Twinning pipe by Mitsubishi (optional parts).
Twinning pipe connection size
ø28.58(1-1/8)
ø22.2(7/8)(ø28.58(1-1/8)) *
PURY-HP144TSNU-A PURY-HP72TNU-A PURY-HP72TNU-A
PURY-HP192TSNU-A PURY-HP96TNU-A
PURY-HP240TSNU-A
ø34.93(1-3/8)
Low pressure
d or f
High pressure
c or e
Unit model
Twinning pipe~Outdoor unit
HP72
ø15.88(5/8)
HP96 HP120
ø19.05(3/4)
ø22.2(7/8) ø28.58(1-1/8)
a b
High pressure
Low pressure
Component unit name
Outdoor unit 1
Package unit name
Outdoor Twinning Kit(optional parts) BC controller
~Twinning pipe
Outdoor unit 2
PURY-HP96TNU-A
PURY-HP120TNU-A PURY-HP120TNU-A
ø22.2(7/8)
ø19.05(3/4)
ø19.05(3/4)
* When the piping length is 65m(213ft) or longer,
use the ø28.58(1-1/8) pipe for the part that exceeds 65m(213ft).
CMY-R200NCBK
CMY-R100NCBK
740(29-3/16) 1240(48-7/8)
1818(71-5/8)
1240(48-7/8)
30(1-3/16)
(5)(1/4)(5)(1/4)
1250(49-1/4) 1250(49-1/4)745(29-3/8)
(5)(1/4)
0000005744.BOOK 16 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
17
2. EXTERNAL DIMENSIONS Hyper Heating Inverter R2-Series
PURY-HP72, 96, 120YNU-A
Unit: mm (in.)
1 2 4 3 5 6 7 8
NO.
740(29-3/16)
70(2-13/16)
150(5-15/16)
85(3-3/8)
85(3-3/8)
130(5-1/8)
150
18(3/4)
1204(47-7/16)
18
1240(48-7/8)
110(4-3/8)
(740)(29-3/16)
185(7-5/16)
29.5
681(678~684)
29.5
94 79
181
160(6-5/16) 243(9-5/8)
150
128(5-1/16)
125
132(5-1/4)
207(8-3/16)
256(10-1/8)
109
129(5-1/8)
84(3-5/16)
90(3-9/16)
54(2-3/16)
135(5-3/8)
20(13/16)
54
592(23-5/16)54(2-3/16)
20(13/16)
148(5-7/8)
152(6) 216(8-9/16)
166
144(5-11/16)
303
1515(59-11/16)
1818(71-5/8)
90(3-9/16)
1060(41-3/4)
90(3-9/16)
172(6-13/16)
(3-3/4) (3-1/8)
(5-15/16)
(6-9/16)
(7-3/16)
(26-13/16)(26-3/4~26-15/16)
(1-3/16)
(11-15/16)
(4-5/16)
(4-15/16)
(2-3/16)
(3/4)
(5-15/16)
(1-3/16)
745(29-3/8)
(745)(29-3/8)
1250(49-1/4)
(5)
(1/4)
(5)(1/4)
(5)
(1/4)
2
5
6
8
(Mounting pitch)
Bottom view
(Mounting pitch)
2×2-14(9/16)×20(13/16) Oval hole
1
Control box
3
4
7
Service panel
Intake
air
Intake
air
Discharge air
Intake
air
Intake
air
2×6-ø4.6(3/16) Hole (Make hole at the plastic fan guard
for snow hood attachment)
<Snow hood attachment hole>
Top v i e w
Front view
Left side view
Rear view
Refrigerant
service valve
<Low pressure>
Refrigerant
service valve
<High pressure>
Note 1. Please refer to the next page for information regarding necessary
spacing around the unit and foundation work.
2. At brazing of pipes, wrap the refrigerant service valve
with wet cloth and keep the temperature of refrigerant service valve under 120°C(248°F).
For transmission cables
For wires
For pipes
Usage Specifications
Front through hole Bottom through hole Front through hole Front through hole Bottom through hole Bottom through hole Front through hole
148(5-7/8) × 84(3-5/16) Knockout hole
ø62.7(2-1/2) or ø34.5(1-3/8) Knockout hole ø43.7(1-3/4) or ø22.2(7/8) Knockout hole ø65(2-9/16) Knockout hole ø52(2-1/16) Knockout hole ø34(1-3/8) Knockout hole
150(5-15/16) × 94(3-3/4) Knockout hole
ø34(1-3/8) Knockout hole
Bottom through hole
Connecting pipe specifications
*1 Connect the refrigerant pipe to the service valve
according to the Installation Manual.
Model
Diameter
Refrigerant pipe Service valve
HP96
ø28.58(1-1/8)
ø19.05(3/4) Brazed *1
ø28.58(1-1/8)
HP72
High pressure Low pressure
ø28.58(1-1/8) Brazed ø22.2(7/8) Brazed *1
HP120
High pressure Low pressure
ø19.05(3/4) Brazed *1ø15.88(5/8) Brazed *1
0000005744.BOOK 17 ページ ２０２０年２月２５日 火曜日 午後５時１９分

MEES19K180
PURY-HP-T(S)NU-A, Y(S)NU-A
18
2. EXTERNAL DIMENSIONS Hyper Heating Inverter R2-Series
PURY-HP72, 96, 120YNU-A
Unit: mm (in.)
1.Required space around the unit 2.Foundation work
Front Front
<Top view>
<Unit:mm(in)>
<Top view>
<To be left open>
Front
Wall <H>
<To be left open>
Front
<Unit:mm(in)>
Wall <H>
<To be left open>
<To be left open>
<To be left open>
Front
Wall <H>
Wall <H>
Wall <H>
Wall <H>
Front
Front
<To be left open>
Wall <H>
Front
Wall <H>
<To be left open>
<To be left open>
Front
Front
Front
Wall <H>
Wall <H>
Front
<To be left open>
<To be left open>
<Wall height limit> Front :Up to the unit height
Back :Up to the unit height Side :Up to the unit height
M10 anchor bolt
<field supply required>
Fixing plate
<field supply required>
Fig.A
<Side view>
Front
Fig.B
●In case of single installation
1 Secure enough space around the unit as shown in the figure below.
· With a space of at least
2 When the height of the walls on the front, back or on the sides<H>
1 Take into consideration the surface strength, water drainage route,
piping route, and wiring route when preparing the installation site. <Note that the drain water comes out of the unit during operation.>
2 Build the foundation in such way that the corner of the installation leg is
securely supported as shown in the right figure.(Fig.A) When using a rubber isolating cushion, please ensure it is large enough to cover the entire width of each of the unit's legs.
3 The protrusion length of the anchor bolt must not exceed 30mm(1-3/16).(Fig.A) 4 Use four fixing plates as shown in the right figure <field supply required>
when using post-installed anchor bolts.(Fig.B)
5 To prevent small animals and water and snow from entering the unit and damaging its parts,
close the gap around the edges of through holes for pipes and wires with filler plates <field supply required>.
6 When the pipes or cables are routed at the bottom of the unit,
make sure that the through hole at the base of the unit does not get blocked with the installation base.
7 Refer to the Installation Manual when installing units on an installation base.
●In case of collective installation
1 When multiple units are installed adjacent to each other, secure enough space to allow
for air circulation and walkway between groups of units as shown in the figures below.
2 At least two sides must be left open. 3 As with the single installation, add the height that exceeds the height limit<h>
to the figures that are marked with an asterisk.
4 If there is a wall at both the front and the rear of the unit, install up to six units
consecutively in the side direction and provide a space of 1000mm(39-3/8) or more as inlet space/ passage space for each six units.
450mm(17-3/4) to the wall on the back of the unit
· With a space of at least
300mm(11-13/16) to the wall on the back of the unit
exceeds the wall height limit as defined below add the height that exceeds the height limit <h> to the figures that are marked with an asterisk.
30 min.* 450 min.* 450 min.*
300 min.*450 min.*
450 min.*
450 min.
30 min. 450 min.450 min.* 450 min. 300 min.*
450 min.* 300 min.*
450 min.*
1000 min.*
900 min. 450 min.*
900 min. 450 min.*450 min.*
30 min.*
450 min.450 min.
450 min.* 450 min.*
30 min.*
(1-3/16) (1-3/16)
(17-3/4) (17-3/4)
(17-3/4) (17-3/4)
(17-3/4) (11-13/16)
(17-3/4) (17-3/4)
(1-3/16)
(17-3/4) (17-3/4)
(1-3/16)
(39-3/8)
(17-3/4)
(35-7/16)
(17-3/4)
(17-3/4)
(17-3/4) (11-13/16)
(17-3/4) (17-3/4) (17-3/4) (11-13/16)
(35-7/16)
(17-3/4)
30mm max.
Unit height h
H
Unit height h
H
(1-3/16)
0000005744.BOOK 18 ページ ２０２０年２月２５日 火曜日 午後５時１９分