Mitsubishi Electric FR-PA07 User manual

1
Enclosure surface operation panel
FR-PA07 INSTRUCTION MANUAL
INVERTER
Thank you for purchasing the enclosure surface operation panel (FR-PA07). This instruction manual
gives handling information and precautions for use of this product. Incorrect handling might cause
an unexpected fault. Before using this product, please read this manual carefully to use this product
to its optimum performance.
Please forward this instruction manual to the end user.
This product is an option dedicated for the FR-E800 */E700/D700/F700PJ/E700EX/D700-G series.
Refer to the inverter unit's Instruction manual for details on the operation panel functions, operation
methods and handling methods.
* Only the FR-E800 standard model is supported.
1. Connection
• Use the FR-CB20connection cable. Insert one end of the cable into the PU connector on the
inverter, and the other end into the connection connector on the FR-PA07 along the guides until
the clips click into place. (For the details of the FR-CB20, refer to the Instruction Manual of the
FR-CB20.)
• To disconnect the cable, hold down the clip at the cable end and gently pull the connector.
Safety precautions
Do not touch the setting dial or keys with wed hands. Doing so may cause an electric shock.
Do not install and operate the enclosure surface operation panel (FR-PA07) if it is damaged
or has parts missing.
Provide a safety backup device, such as an emergency brake, to protect machines and
product from hazardous conditions if the enclosure surface operation panel (FR-PA07)
becomes faulty.
Static electricity in your body must be discharged before you touch the product. Otherwise
the product may be damaged.
If halogens (including fluorine, chlorine, bromine, and iodine) contained in fumigants for wood
packages enter this product, the product may be damaged. Prevent the entry of fumigant
residuals or use an alternative method such as heat disinfection. Note that sterilization or
disinfection of wood packages should be performed before packing the product.
NOTE
Do not start operation with the inverter front cover removed.
Clip
FR-PA07 (back) PU connector
Clip
Example: FR-E700

2
2. Names and functions of the operation panel
(FR-PA07)
* Both PU and EXT are off on the inverters manufactured during or before the period shown by the serial
numbers described on page 7.
Unit indication
Hz: Lit to indicate frequency.
A: Lit to indicate current.
(Off to indicate voltage and
flicker to indicate set frequency
monitor.)
Rotation direction
indication
On:
Indicates that forward rotation
operation is being performed.
Slow flickering (1.4s cycle):
Reverse rotation operation
Fast flickering (0.2s cycle):
When the forward/reverse
rotation command is given
and the frequency
command is not given.
When the MRS signal is
input.
Start command forward
rotation
Start command reverse
rotation
Monitor (4-digit LED)
Shows the frequency,
parameter number, etc.
Monitor indication
Lit to indicate monitoring mode.
Operation mode indication
PU: Lit to indicate PU operation
mode.
EXT: Lit to indicate external
operation mode.
PU, EXT: Flicker to indicate
network operation mode. *
Setting dial
(Setting dial: Mitsubishi Electric
inverter dial)
Used to change the frequency
setting and parameter values.
Mode switchover
Used to change each setting
mode.
Stop operation
Uses to stop the operation
command.
When a fault occurs, it can be
reset.
Determination of each
setting
If pressed during operation,
monitor changes as below;
Operation mode
switchover
Used to switch between the PU
and external operation mode.
When using the external
operation mode (operation
using a separately connected
frequency setting potentiometer
and start signal), press this key
to light up the EXT indication.
Change Pr. 79 setting to change
to combined mode.)
PU: PU operation mode
EXT: External operation mode
MODE SET
RUNRUN MONMON
EXTEXT
PUPU
HzHz
A
STOP
RESET
REV FWD
PU
EXT
Running frequency
Output current
Output voltage

3
3. Operation
3.1 Basic operation
Basic operation is as follows.
The parameter copy function is not available in this product.
REMARKS
When Pr.551 PU mode operation command source selection = "9999 (initial value)", the
priority of the command source in PU operation mode is defined as follows: USB
connector > FR-PA07 > operation panel. (Whether a USB connector is provided
depends on the inverter model. For details, refer to the Instruction Manual of the
inverter to be used.)
DE SET
P
E
DE SET
P
E
DE SET
P
E
DE SET
P
E
DE SET
P
E
T
PU
EXT
T
PU
EXT
Hz
A
Hz
A
RUN MON
EXT
PU
Hz
A
RUN MON
EXT
PU
Hz
A
RUN MON
EXT
PU
Hz
A
RUN MON
EXT
PU
Hz
A
MODE S
MODE S
MODE S
T
PU
EXT
DE SET
P
E
Operation mode switchover
At power-ON (external operation mode)
PU operation mode
(output frequency monitor)
Monitor/frequency setting
Value change
Output current
monitor
Parameter setting
Parameter setting mode
Fault history
PU Jog operation mode
(Example)
(Example)
and frequency alternating.
Frequency setting written
and complete
Output voltage
monitor
Display the
current setting
Parameter clear All parameter
clear
Fault history clear
Initial value change list
Value change
Parameter write complete
Parameter and a setting value
alternating.
[Operation for displaying fault history] (Refer to the Instruction Manual of
the inverter.)
The last eight fault records can be displayed. (On the display of the last
fault record, a decimal point LED is ON.)
When the fault history is empty, is displayed.

4
3.2 Operation lock (Press [MODE] for a while (2 seconds))
 Set "10 or 11" in Pr. 161 , then press for 2 seconds to make the setting dial and key operation
invalid.
 When the setting dial and key operation is made invalid, appears on the operation panel.
When the setting dial and key operation is invalid, appears if the setting dial or key
operation is performed. (When the setting dial or key operation is not performed for 2 seconds, the
monitor display appears.)
 To make the setting dial and key operation valid again, press for 2 seconds.
Operation using the setting dial and key of the FR-PA07 can be made invalid to
prevent parameter change, and unexpected start or frequency setting.
POINT
Set "10 or 11" (key lock mode valid) in Pr. 161 Frequency setting/key lock operation
selection.
Operation Display
1. Screen at powering on
The monitor display appears.
2. Press to choose the PU operation mode. PU indication is lit.
3. Press to choose the parameter setting
mode. (The parameter number read previously
appears.)
4. Turn until (Pr. 161) appears.
5. Press to read the currently set value.
" " (initial value) appears.
6. Turn to change it to the set value " ".
7. Press to set.
Alternating ... Parameter setting complete
8. Press for 2 seconds to show the monitor
mode.
Press for 2 seconds.
Functions valid even in the
operation lock status
Stop and reset with .
RUNRUN MONMON
EXTEXT
PUPU
HzHz
A
RUNRUN MONMON
EXTEXT
PUPU
HzHz
A
RUNRUN MONMON
EXTEXT
PUPU
HzHz
A

5
3.3 Use the setting dial like a potentiometer to perform operation
Note
Release the operation lock to release the PU stop by key operation.
POINT
Set "1" (setting dial potentiometer mode) in Pr. 161 Frequency setting/key lock
operation selection.
Changing example Changing the frequency from 0 Hz to 60 Hz during operation
Operation Display
1. Screen at powering on
The monitor display appears.
2. Press to choose the PU operation
mode.
PU indication is lit.
3. Change the Pr. 161 setting to "1".
(Refer to page 4 for change of the setting.)
Press twice to return the monitor to frequency monitor.
4. Press / to start the inverter.
5. Turn until " "(60.00 Hz)
appears. The blinking frequency is the set
frequency.
You need not press . The frequency blinks for about 5s.
REMARKS
If blinking "60.00" turns to "0.00", the Pr. 161 Frequency setting/key lock operation
selection setting may not be "1".
Independently of whether the inverter is running or at a stop, the frequency can be set by
merely turning the . (Use Pr. 295 Magnitude of frequency change setting to change the
frequency setting increments of .)
RUNRUN MONMON
EXTEXT
PUPU
HzHz
A
RUNRUN MONMON
EXTEXT
PUPU
HzHz
A
FWD REV
FWD
REV
RUNRUN MONMON
EXTEXT
PUPU
HzHz
A

6
4. Specifications
4.1 Standard specifications
* Temperature applicable for a short time, for example, in transit.
4.2 Outline drawing and panel cutting drawing
<Outline drawing> <Panel cutting drawing>
Item Specifications
Surrounding air
temperature -10°C to +50°C (non-freezing)
Ambient humidity 90%RH or less (non-condensing)
Storage temperature -20°C to +60°C*
Ambience Indoors (free from corrosive gas, flammable gas, oil mist, dust and dirt)
Altitude, vibration Maximum 1000m above sea level for standard operation. 5.9m/s2 or less
at 10 to 55 Hz (directions of X, Y, Z axes)
Power supply Power is supplied from the inverter.
Connection method Connection using the parameter unit connection cable (FR-CB20)
68
45
59
36
22
22
11
20
(15.5)
24
2-M3 screw
(Unit: mm)

7
5. Instructions
 For the FR-E700 series inverters manufactured during or before the period shown by
the following serial numbers, there are restrictions mentioned below.
• Parameter copy ( ) is displayed, but parameter copy (reading, writing, or
verification) does not function. Display turns into the reading indication, but reading is not
executed. If writing or verification is executed, an error occurs.
• Initial value change list ( ) cannot be used.
• Easy setting mode (press and simultaneously (0.5 seconds)) cannot be used
to change the operation mode.
• SERIAL number check
Refer to the Instruction Manual of the inverter for the position of the rating plate.
* The parameter copy menu () is not displayed on this product connected to FR-E700 series
inverters manufactured after the above period.
 The parameter copy ( ) is not displayed on this product when connected to FR-E800
series inverters.
Rating plate example The SERIAL consists of one symbol, two
characters indicating production year and
month, and six characters indicating control
number.
The last digit of the production year is indicated
as the Year, and the Month is indicated by 1 to
9, X (October), Y (November), or Z (December).
   
Symbol Year Month Control number
SERIAL (Serial No.)
Type SERIAL number Type SERIAL number
FR-E720-0.1K to 0.75K J7 FR-E740-0.4K to 7.5K D7
FR-E720-1.5K to 5.5K K7
FR-E720-7.5K L7
FR-E720-11K, 15K G7

HEAD OFFICE: TOKYO BUILDING 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
6. Restricted Use of Hazardous Substances in
Electronic and Electrical Products
The mark of restricted use of hazardous substances in electronic and electrical products is applied
to the product as follows based on the “Management Methods for the Restriction of the Use of
Hazardous Substances in Electrical and Electronic Products” of the People's Republic of China.
电器电子产品有害物质限制使用标识要求
本产品中所含有的有害物质的名称、含量、含有部件如下表所示。
·产品中所含有害物质的名称及含量
上表依据SJ/T11364的规定编制。
○：表示该有害物质在该部件所有均质材料中的含量均在GB/T26572规定的限量要求以下。
×：表示该有害物质在该部件的至少一种均质材料中的含量超出GB/T26572规定的限量要求。
∗1 即使表中记载为 ×，根据产品型号，也可能会有有害物质的含量为限制值以下的情况。
∗2 根据产品型号，一部分部件可能不包含在产品中。
环境保护使用期限标识
部件名称∗2
有害物质∗1
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
电路板组件 （ 包括印刷电路板及其构成的零部件，
如电阻、电容、集成电路、 连接器等）、电子部件
×○×○ ○ ○
金属壳体、金属部件 ×○○○ ○ ○
树脂壳体、树脂部件 ○○○○ ○ ○
螺丝、电线 ○○○○ ○ ○
IB(NA)-0600350ENG-C (2002)MEE Printed in Japan Specifications subject to change without notice.