Mitsubishi MOTORS MZ380465EX User manual

INSTALLATION MANUAL
REAR PARKING ASSIST SENSORS
Thank you for purchasing MITSUBISHI genuine * PARKING SENSOR SYSTEM *. This manual ex-
plains the procedure for installing * PARKING SENSOR SYSTEM *. Read this manual thoroughly
before installation to ensure proper work.
PART NUMBER APPLICABLE MODEL
MZ380465EX OUTLANDER
BILL OF MATERIALS:
#1 Wire Harness: 1 #2 Wire Harness: 1 #3 Wire Harness: 1 #4. Foam Pad: 9
#5. Module: 1
#6. Sensors: 4 #7. 26mm Paster: 2
#9. Buzzer: 1
#10. Sensor Clips: 4
#11. Tie Wraps: 20
#8. 24mm Paster: 2
MITSUBISHI MOTORS
GENUINE ACCESSORIES

2
TOOLS
3mm
15mm
24mm
26mm
10mm

3
1
22
2
3 4
5
BEFORE INSTALLATION:
Disconnect NEGATIVE terminal
6

4
9
7 8
Repeat RH Side

5
10A
10C
10
10B

6
12 13
14 15
11 #8. 24mm #7. 26mm #7. 26mm #8. 24mm

7
17
18 19
20 21
16

8
22 23
24 25
26 27

9
28 29
30
31 32 33
3mm
3mm
24mm 24mm
26mm
24mm / 26mm

10
#3. Harness
#6. Sensors
#6. Sensor #6. Sensor
#4.
#10.
34
35
#10.

11
220mm
#2. Harness
#1. Harness
36
37

12
40
LINE COLOR
1- None
2 -White/Black line
3 - Orange / Black Llne
4 - Blue / White line
5 - Red / White line
6 - Yellow / Green Line
1 2 3 4 5 6
#2. Harness
#1. Harness
#2. Harness
38
39
41

13
42 A 42 B
42 A & B
#2. Harness
A B
#11
#1. Harness
#5.
#1. Harness
C
CAUTION: Use
thick white wire!
#11
#11 #11
#4.
#4.
GND
42
42 C

14
43 44
45
47 47 A
155mm
55mm
55 mm
46
# 9
# 4
# 9
15mm
# 1
15mm
155mm
# 9

15
48
49 50
TEST
47B
29
28
27
26
24
23
18
17
16
15
14
13
12
9
8
7
6
5
4
3
2
# 11

Function inspection- Troubleshooting
Symptom
Possible Cause
Confirmation Method
Solution
When the gear is
shifted to “R”, the alert
does not beep.
The buzzer plug has not
been inserted.
Confirm whether the
buzzer plug is inserted.
Insert the buzzer plug
correctly.
Tail light power wire
has not been spliced
correctly.
Check if reverse lights
are on or that the thick
white wire has been
spliced.
Splice the thick white
wire.
The fuse to the ECU
may have blown.
Check whether the fuse
has been blown.
Replace the fuse with a
new one.
ECU is damaged.
Confirm whether the
ECU is damaged.
Replace ECU with a
new one.
When the gear is
shifted to “R”, the alert
beeps twice, not once.
One or more of the
sensors is not
connected properly.
Confirm whether the
sensors are properly
connected.
Connect the plug of
each sensor properly.
One of the sensors may
be damaged.
Confirm whether each
sensor functions
properly.
Replace any damaged
sensor with a new one.
When the gear is
shifted to “R”, the alert
beeps three times.
Two of the sensors are
not connected properly
or may be damaged.
Confirm whether the
sensors are properly
connected and whether
each sensor functions
properly.
Connect the plug of
each sensor properly
and replace any
damaged sensors with
a new one.
When the gear is
shifted to “R”, the alert
beeps four times.
Three or more of the
sensors are not
connected properly or
may be damaged.
Confirm whether the
sensors are properly
connected and whether
each sensor functions
properly.
Connect the plug of
each sensor properly
and replace any
damaged sensors with
a new one.
The sensor’s harness
has not been
connected to the ECU.
Confirm whether the
harness has been
connected properly.
Connect the plug of the
harness to the ECU.
16

The gear is in “R” but
the warning does not
go off although there
are objects behind the
vehicle.
One of the sensors is
damaged.
Confirm whether each
sensor functions
properly.
Replace any damaged
sensor with a new one.
The objects are outside
the range of detection.
Refer to the service
manual for the range of
detection.
(The warning does not
go off when objects are
outside the detection
area).
ECU is damaged.
Confirm whether the
ECU is damaged.
Replace ECU with a
new one.
The gear is in “R” and
the warning goes off
for a while although
there is no object
behind the vehicle.
The sensor surface is
covered with foreign
materials such as mud,
water drops, etc.
Confirm whether the
sensor surface is
covered with foreign
materials.
Clean up the sensor
surface and see if it
functions normally.
One of the sensors is
damaged.
Confirm whether each
sensor functions
properly.
Replace any damaged
sensor with a new one.
The gear is in “R”, and
the warning goes off
intermittently although
there is no object
behind the vehicle.
The sensors are not
installed in the proper
position.
Confirm whether the
sensors are installed in
the proper position.
Reinstall the sensors in
the proper position.
The sensors have
detected harsh roads.
Confirm the road
condition.
(Misdetection is
possible when the
system detects harsh
roads or small objects
on the road.)
The vehicles posture is
weighted heavily to
one side.
Confirm the vehicles
posture.
Misdetection may
occur if the vehicle is
heavily weighted in the
rear or at the cusp of a
steep incline. (Refer to
service manual for
figure.)
17

18
Product specification
Items Specification
Rated Voltage DC 12.0V
Operation Voltage DC 9.6V~ 16V
Operation Temp -20Ԩ~ 70Ԩ
Storage Temp -30Ԩ~ 80Ԩ
Items Specification
Rated VoltageDC 12.0V
Operation Voltage DC 9.6V~ 16V
Operation Temp -20Ԩ~ 70Ԩ
Storage Temp -30Ԩ~ 80Ԩ

19
SET PRINTER TO : “ACTUAL SIZE” or “NONE” NOT “SCALE
REAR PARK ASSIST TEMPLATES / MODEL YEARS 2007 ON
REVERSE FOR RIGHT SIDE