Mitsubishi MZ380552EX User manual

1
ASX / OUTLANDER SPORT / RVR
REAR VIEW CAMERA
MZ380552EX
INSTALLATION AND HANDLING INSTRUCTIONS
Thank you for purchasing the Mitsubishi Genuine Accessory.
To install and use the product correctly with proper knowledge of it, read this publication carefully.
Keep this publication for reference when maintenance is required.
Attention
・This publication gives precautionary instructions in the boxes titled as follows.
Read through these instructions thoroughly.
Describes precautions that should be observed in order to prevent injury or damage
to the vehicle or its components, which may occur if sufficient care is not taken.
Provides additional information that facilitates installation work.
・Failure to follow these instructions not only prevents the product from working properly but may lead to trouble
with the vehicle. Be sure to follow all instructions carefully.
・If there is anything unclear about the installation, handing and/or usage of the product, contact your Mitsubishi
Motors dealer for clarification.
・Mitsubishi Motors Corporation is not responsible for any defects or difficulties caused by or resulting from the
failure to follow given instructions.
・We recommend you to have the installation performed at an authorized Mitsubishi Motors dealer.
ＪＩ２６１３７３
１０．７
To the dealer:
Be sure that the customer receives this publication.
Navigation (MMCS) unit Camera

2
TOOLS（Make the following tools ready for use.）
Socket wrench Philips screwdriver Flat-blade screwdriver Trim remover
Utility knife Scissors Wire Cloth tape Vinyl tape
COMPONENTS (Make sure that all of the following components were included in the kit.)
①Camera : 1 ②Urethane-tape :7 ③Cable Tie : 35
④Installation and Handling Instructions
: 1 (this document)
REQUIRED COMPONENTS (sold separately)
Camera Harness (MZ360339EX)
(for Right-hand Drive Vehicle)
Camera Harness (MZ360338EX)
(for Left-hand Drive Vehicle)

3
Fasten the additional
harness to an existing
vehicle harness using
tape or cable ties.
Bind up extra length of
the harness using a
cable tie.
short, use two con-
nected together.
Check the product and
wiring for installed con-
dition before connect-
ing the cable to the
battery.
Check the installed
product for function.
Also check lamps,
horn, wipers, etc. for
proper operation.
When disconnecting
connectors, first unlock
them, then separate the
connectors by pulling
on themselves, not on
cables.
When connecting con-
nectors, push them
against each other until
the lock clicks.
Do not pull on wiring
harnesses strongly.
Do not let harnesses be
pinched between parts.
Route the harness
away from hot compo-
nents such as the
engine and radiator.
Protect the harness
from sharp edges by
covering the edges with
tape or other suitable
materials.
Apply sealant to grom-
mets at portions where
the harness run
through.
Do not fasten the har-
ess to brake pipes or
high pressure air condi-
tioner pipes.
Be sure to disconnect
the negative terminal
cable from the battery.
Loosen or tighten bolts
and nuts using tools
that match their sizes.
Use a Phillips screw-
driver that fits the
recess in the head of
the screw being loos-
ened or tightened.
To remove plastic
parts, use a trim
remover.
Before installation When installing or removing parts
Clamping harness
Wiring
After installation
If one cable tie is too

A. Vehicle Parts Removal (Refer to workshop manual for how to remove vehicle parts.)
Left-hand Drive Vehicle Right-hand Drive Vehicle
Instrument Panel ASSY Center
MMCS
Front Seat ASSY
(Driver’s Seat)
Front Console
Side Cover (L)
Instrument Panel ASSY Center
MMCS
Front Console
Side Cover (L)
Front Seat ASSY
(Passenger’s Seat)
Center Pillar
Trim Lower (L)
Rear Scuff Plate (L)
Tailgate Trim
Upper
Tailgate Trim
Tailgate Trim
Upper (R)
Cargo Floor Box
(Center)
Rear End Trim Cargo Floor Lid
Tailgate Trim
Upper (L)
Quarter Trim
Lower (L)
Cargo Floor
Box (L)
Quarter Trim
Upper (L)
Foot Plate
Front Scuff Plate (L)
Cowl Side Trim (L)
Cowl Side Trim (L)
Front Scuff Plate (L)
PRECAUTIONS
Be sure to apply the parking brake securely. Remove the ignition key from the key cylinder .
When removing and reinstalling the vehicle parts, perform the work including the tightening torques in accor-
dance with the workshop manual.
Disconnecting the (–) cable from the battery causes the radio and audio presets, the clock, etc. to lose their
memory. Record the contents of the memory before disconnecting the battery (-) cable to allow you to repro-
gram the radio presets after the installation is completed. Open the rear tailgate first prior to disconnecting
the battery (-) cable.

Vinyl Tape
Camera Cable
Pin Terminal
For Left-hand Drive Vehicle
(1) Wrap the camera cable (around the pin
terminal) with vinyl tape up to the cable end
for protection.
Caution
Be careful not to bend or break the terminal
when wrapping the cable with protective
vinyl tape.
It may cause damage, disconnection or
loose connection of the terminal.
B. Wiring of Camera Cable
B-1. Preparation for Wiring Camera Cable
B-2. Wiring of Camera Cable to Navigation
Connector for Camera
Note: Illustration of LHD is provided here
as an example.
(*) Disconnect any camera
cable connected to MMCS
and bind it up with tape.
Camera Cable

For Right-hand Drive Vehicle
Connection of Camera Cable Terminals
Joint Surface Joint Surface Side View
Red White
Blue Transparent Black 24P Connector
(1) Disconnect a 24P connector from the
navigation.
Caution
Be careful not to connect terminals
mistakenly.
It may cause malfunction.
①Disengage stoppers on the 24P connector.
②Insert camera cable terminals into the 24P
connector as shown in left-hand illustration.
③Engage the stoppers.
A Arrow View Red White
Blue Transparent Black
Terminal Surface
ACC (Red)
VRV (White)
R-EX (Blue)
SB (Transparent)
GND (Black) Camera Cables
Disengage stoppers by pressing
claws on both sides. Engage stoppers.
(2) Connect the connector side of the 24P
connector to MMCS.
Connect 24P connector.
Note: Illustration of RHD is provided here
as an example.
24P Connector

For Left-hand Drive Vehicle For Right-hand Drive Vehicle
Cable Tie
Cable Tie
B-3. Wiring of Camera Cable to Vehicle Rear
Camera Cable
Camera Cable
Camera Cable
Camera Cable
Cable Tie
Cable Tie
Cable Tie
Vehicle Front
Vehicle Front
Flip over
(1) Wire the camera cable to the navigation attachment area.
Fix the camera cable to the vehicle harnesses with cable ties.
(2) Wire the camera cable on the left side of
vehicle along vehicle harnesses toward
the rear.
Fix the camera cable to vehicle harnesses
with cable ties.

Cable Tie
Cable Tie
Cable Tie
Urethane Tape Wrap with half-cut urethane tape.
Roof Lining
Cable Tie
Urethane Tape
Camera Cable
Camera
Cable
Camera Cable
Half-cut Urethane Tape
Half-cut Urethane Tape
Wrap with
tape.
Wire Grommet Wire
Grommet
Apply urethane
tape at the edge.
Insert terminals into 6P coupler.
Protect the washer hose from damage by bending
the edge of wire into horseshoe shape.
(4) Wrap the camera cable with half-cut urethane
tape.
(3) Wire the camera cable on the left side of
vehicle along vehicle harnesses toward
the rear.
Fix the camera cable to vehicle harnesses
with cable ties.
(5) Flip the edge of the roof lining slightly and
wire the camera cable inside the roof lining.
(6) Remove a grommet from the vehicle.
(7) Use wire to pass the camera cable through
the grommet and wire the cable to the
tailgate.
(8) Wire the camera cable along
vehicle harnesses on the
tailgate.
Fix the camera cable to
vehicle harnesses with cable
ties.
(9) Remove the vinyl tape
protecting the pin terminals
of the camera cable.
(10) Insert the pin terminals of
the camera cable into the
6P coupler.
(Refer to Connection of
Camera Cord Terminals on
page 9.)

Connection of Camera Cord Terminals
Red
White
Transparent
Joint Surface Side View
Blue
Joint Surface
①Remove the stopper from the 6P coupler.
②Insert camera cable terminals into the 6P
coupler as shown in illustration below.
Caution
Be careful not to connect terminals
mistakenly.
It may cause malfunction.
③Attach the stopper.
Remove stopper. Attach stopper.
R-EX (Blue)
VRV (White)
SB (Transparent)
ACC (Red)
Camera Cord
Attach 6P connector.
Camera Cable
Cover
Clip
Clip
Camera
Camera Cable
Camera Cord
6P Connector
Camera Connector
Connect camera connector.
(11) Attach the 6P connector to a hole on the
tailgate panel.
(12) Remove the clip and the cover.
(13) Attach the camera and reinsert the clip
removed at Step (12).
(14) Connect the camera connector to the 6P
connector.

Connecting Diagram
For Left-hand Drive Vehicle For Right-hand Drive Vehicle
MMCS MMCS
24P Connector
Camera Cable
Rear View Camera
Rear View Camera
Camera Cable
Connector
for Camera

C. Reinstallation of Vehicle Parts
Refer to workshop manual for how to reinstall removed vehicle parts.
Operation Confirmation
(1) Ensure that all the connections have been properly performed according to the connecting diagram.
(2) Check for the battery and turn the ignition switch to the IGN position.
(3) Confirm the state of connection and operation according to the operation manual.
Confirmation of Major Parts
(1) Ensure that electric components, such as horn and wiper, operate properly.
(2) Check for the seat fixation bolts and the tightening torque of nuts.
(3) Ensure that all the parts fixed with Velcro fastenings or double-faced tape are fixed securely and that
there is no loose cable tie.
(4) Reprogram the clock and radio frequency memories. (Refer to each workshop manual for the procedure.)