Mitsubishi MELIMP Series User manual

DRIVE UNIT
H igh Perform ance & H igh Function
MAGNETIC MOTOR
SERIES
SPECIFICATIONS/INSTRUCTION M ANUAL
M D -A X 520-0.5K to 3.5K
PRE-OPERATION
IN F O R M A T IO N
IN STALLATIO N C hapter1
C hapter2
C hapter3
C hapter4
Chapter5
C hapter6
C hapter7
Chapter8
W IRING
HOW TO USE THE
OPERATION PANEL
OPERATION
PARAM ETER
FUNCTIONS
TROUBLESHOOTING
SPECIFICATIONS
C hapter1
Get other manuals https://www.bkmanuals.com

1
Please read here first
Thank you for choosing the Mitsubishi Magnetic Motor Drive Unit. This instruction manual gives
handling information and precautions for use of the drive unit.
Incorrect handling of the equipment may cause an unexpected fault. To optimize the unit capability,
please read this manual carefully before using the equipment.
Please refer to the Mitsubishi Magnetic Motor Instruction Manual for the Mitsubishi Magnetic Motor.
General precautions
Please forward this instruction manual to the end user.
Many of the diagrams and drawings in this instruction manual show the drive unit without a
cover, or partially open. Never run the drive unit in this manner. Always replace the cover
and follow this instruction manual when operating the drive unit.
After reading this manual, store it carefully in a place where it is easily accessible for the
operator.
This instruction manual is subject to modifications for specification changes and manual
improvements. After such modifications have been made, the instruction manual will be
published as a revised version with a new number located on the bottom left of the back
cover.
For safe operation of this product
This product has not been designed or manufactured for use in or with a device or system
which will be used under circumstances where life may be endangered.
Consult with Mitsubishi if you are planning to use this product for special purposes, e.g.
equipment or systems designed for manned transport vehicles, medical purposes,
aerospace, nuclear power, electric power or undersea junctions.
This product has been manufactured under strict quality control. However, when installing
the product where serious accidents or losses could occur if the product fails, install
appropriate safety devices in the system.
Do not use this product with any load other than the specified motor.
You cannot use a single drive unit with two or more motors.
Get other manuals https://www.bkmanuals.com

2
Please read here first (Continued)
Safety Instructions
This section is specifically about safety matters
Do not attempt to install, operate, maintain or inspect the drive unit until you have read
through this instruction manual and appended documents carefully and can use the
equipment correctly. Do not use the drive unit until you have a full knowledge of the
equipment, safety information and instructions.
In this instruction manual, the safety instruction levels are classified into "WARNING" and
"CAUTION".
WARNING Assumes that incorrect handling may cause hazardous conditions,
resulting in severe injury or death.
CAUTION Assumes that incorrect handling may cause hazardous conditions,
resulting in medium or slight injury, or may cause physical damage
only.
Note that the CAUTION level may lead to a serious consequence according to conditions.
Please follow the instructions of both levels because they are important to personal safety.
NOTICE denotes the items which do not correspond to "WARNING" or "CAUTION" but
should be observed by the customer.
MEMO denotes the items which the user should know for operation.
Get other manuals https://www.bkmanuals.com

3
Please read here first (Continued)
1. Usage
WARNING
The MELIPM series motor is a synchronous motor with high-performance magnets built in
its rotor. Therefore, after the drive unit is powered off, there are high voltages at the motor
terminals while the motor is running. Before starting wiring or maintenance and inspection,
make sure that the motor has stopped. In any application where the motor is rotated by a
load such as a fan or blower, connect a low-voltage manual switch on the drive unit's
output side, open the switch, and start wiring or maintenance and inspection. Not doing so
can cause an electric shock.
Never disassemble or modify the unit. Doing so can cause an electric shock, fire or injury.
Do not use the unit with any load other than the specified motor. Doing so can cause a fire
or injury.
Provide safety devices for the whole system, e.g. emergency brakes, to ensure that the
machine or device is not placed in hazardous conditions when the drive unit fails.
CAUTION
If a holding brake is required, prepare it separately. The brake function of the drive unit
cannot keep holding the load. Injury may result.
Before operating the drive unit which had been stored for an extended period of time,
perform inspection and test operation on the unit before using. Not doing so may cause
accidents.
2. Transportation
CAUTION
Do not stack the drive unit boxes higher than the number indicated on the package. Doing
so can cause injury.
Confirm the weight before carrying the drive unit. Not doing so can cause injury.
When carrying the drive unit, do not exert a force partially, i.e. do not hold the front cover
operation panel. Doing so can cause the unit to drop, leading to injury.
The drive unit is precision piece of equipment. Do not drop it or subject it to impact, this
may damage the drive unit.
3. Installation
CAUTION
Do not install or operate the drive unit if it is damaged or has parts missing. Such
installation or operation can cause accidents.
Always install the drive unit in the specified orientation and environment. Not doing so can
cause a fire or accidents.
Install the drive unit on an incombustible material such as metal. Not doing so can cause a
fire.
Do not place combustible materials nearby. Doing so can cause a fire.
Install the drive unit in a load-bearing place. Not doing so can cause accidents.
Prevent screws, metal pieces or other conductive foreign matter, or wood scrap, oil or
other flammable foreign matter from entering the drive unit. They can cause a fire or
accidents.
Get other manuals https://www.bkmanuals.com

4
Please read here first (Continued)
4. Wiring
WARNING
Any person who is involved in the wiring of this equipment should be fully competent to do
the work. Otherwise, an electric shock or fire can occur.
Install a no-fuse breaker or earth leakage circuit breaker. Otherwise, a drive unit failure
can cause large currents to flow, resulting in a fire.
Always install the unit before wiring. Otherwise, an electric shock or fire can occur.
Before restarting wiring after power-on, make sure that the motor is at a stop, wait for more
than 10 minutes after switching power off, and confirm that the DC voltage across the DC
terminals P/+ and N/- is low enough to do the work. Immediately after power-off, the DC
terminals P/+, N/- are charged with more than 200V (residual voltage of the internal
capacitor). Therefore, an electric shock may occur.
Even after power-off, the motor connection terminals U, V, W have high voltages while the
motor is running. Always start wiring after confirming that the motor has stopped. Not
doing so can cause an electric shock.
Earth the drive unit. Not doing so can cause an electric shock or fire.
CAUTION
Make sure that the input power supply voltage matches the rated voltage specifications.
Mismatch can cause a fire or accidents.
Check the terminal layout and terminal symbols to ensure that connections are correct.
Wrong connections can cause a fire or accidents.
Do not connect a power supply to the motor connection terminals U, V, W. Doing so can
cause a fire or accidents.
Connect the motor connection terminals U, V, W to match the motor phase sequence.
Wrong connections can cause accidents due to reverse rotation of the motor.
Do not connect a resistor across the DC terminals P/+-N/-. Doing so can cause a fire or
accidents.
Take measures to prevent peripheral sensors and equipment from malfunctioning due to
electromagnetic noises. Not doing so can cause accidents.
Take measures to prevent peripheral power capacitors and generators from overheating or
being damaged due to power harmonics. Not doing so can cause a fire.
Connect the power capacitor, surge suppressor and radio noise filter (FR-BIF option) on
the power supply side. Connection on the output side can cause a fire.
Get other manuals https://www.bkmanuals.com

5
Please read here first (Continued)
5. Operation
WARNING
Always replace the front cover before switching input power on. While power is on, do not
remove the front cover. Doing so can cause an electric shock.
Operate the switches with dry hands. Not doing so can cause an electric shock.
Prepare an emergency stop switch separately. The "STOP/RESET" key of the operation
panel or parameter unit is valid for stopping only when the function setting has been made.
Not using a separate emergency stop switch can cause accidents.
When the stall prevention function is activated, operation will be performed independently
of the preset acceleration/deceleration time and preset speed. Design the machine to
ensure safety if the stall prevention function is activated. Not doing so can cause
accidents.
Selecting the retry function will restart the drive unit suddenly when it is at an alarm stop.
Design the machine to ensure personal safety if the drive unit is restarted. Not doing so
can cause accidents.
At the occurrence of an alarm, turn off the run signal before resetting the alarm. The drive
unit will restart abruptly if you reset the alarm with the run signal on. It can cause injury.
At occurrence of an alarm, turn off the run signal. If you do not turn off the run signal, the
alarm may be reset due to power OFF-ON at occurrence of an instantaneous power failure
or like, restarting the drive unit suddenly. It can cause injury.
CAUTION
You can set the motor speed easily between low speed and high speed. Set the speed
command which will not exceed the permissible range of machine design. Not doing so
can cause accidents.
If the motor is rotated by the load, ensure that the motor will not exceed its maximum
speed. The drive unit may be damaged.
While power is on or some time after power-off, do not touch the heat sink and brake
resistor as they are hot. You may get burnt.
The electronic overcurrent protection function for motor overheat protection is initialized
when the drive unit is reset. Frequent resetting of the drive unit will disable motor overheat
protection. The motor may be burnt if it is operated under overload.
Get other manuals https://www.bkmanuals.com

6
Please read here first (Continued)
6. Maintenance, Inspection and Part (Cooling Fan) Replacement
WARNING
Any person who is involved in maintenance, inspection or part replacement should be fully
competent to do the work. Otherwise, an electric shock or injury can occur.
Before starting maintenance, inspection or part replacement, make sure that the motor is
at a stop, wait for more than 10 minutes after switching power off, and confirm that the DC
voltage across the DC terminals P/+ and N/- is low enough to do the work. Immediately
after power-off, the DC terminals P/+, N/- are charged with more than 200V (residual
voltage of the internal capacitor). Therefore, an electric shock may occur.
Even after power-off, the motor connection terminals U, V, W have high voltages while the
motor is running. Always start the work after confirming that the motor has stopped. Not
doing so can cause an electric shock.
Do not conduct a pressure test. A pressure test can damage the drive unit.
Do not perform an insulation resistance test on the control circuit using a megger. Such a
test can damage the drive unit.
While power is on, do not replace the cooling fan. Replacing the cooling fan during power-
on can be hazardous.
7. Disposal
CAUTION
Dispose of the drive unit as general industrial waste. Its solder (lead) can cause
environmental contamination.
Get other manuals https://www.bkmanuals.com

7
 CONTENTS 
Page
1. PRE-OPERATION INFORMATION 1-1
1.1 Checking the Product 1-2
1.1.1 Contents............................................................................................ 1-2
1.1.2 Type ..................................................................................................1-2
1.1.3 Drive units to be used with motors..................................................... 1-2
1.2 Parts Identification 1-3
1.3 Handling of the Cover and Operation Panel 1-4
1.3.1 Removal and reinstallation of the front cover..................................... 1-4
1.3.2 Handling of the wiring cover............................................................... 1-4
1.3.3 Removal and reinstallation of the operation panel .............................1-5
1.4 Transportation 1-6
1.5 Storage 1-6
2. INSTALLATION 2-1
2.1 Checking the Installation Environment 2-2
2.1.1 Operating environment ......................................................................2-2
2.1.2 Installation in control box................................................................... 2-3
2.2 Preparation of Peripheral Devices 2-5
2.2.1 Basic configuration ............................................................................2-5
2.2.2 Selection of peripheral devices.......................................................... 2-6
2.3 Installation Method 2-9
3. WIRING 3-1
3.1 Pre-Wiring Instructions 3-3
3.1.1 Terminal connection diagram.............................................................3-3
3.1.2 Noises ...............................................................................................3-4
3.2 Wiring of the Main Circuit Terminals 3-5
3.2.1 Terminals...........................................................................................3-5
3.2.2 Terminal layout and connection specifications...................................3-5
Get other manuals https://www.bkmanuals.com

8
3.2.3 Wiring of the AC power input terminals R, S, T..................................3-6
3.2.4 Wiring of the control circuit power supply terminals R1, S1................3-6
3.2.5 Wiring of the motor connection terminals U, V, W..............................3-7
3.2.6 Wiring of the ground terminals ......................................................3-7
3.2.7 Wiring of the DC reactor connection terminals P/+, P1 ......................3-8
3.2.8 Wiring of the brake resistor connection terminals P/+, PR .................3-8
3.2.9 Wiring of the DC terminals P/+, N/-....................................................3-9
3.3 Wiring of the Control Circuit Terminals 3-11
3.3.1 Terminals......................................................................................... 3-11
3.3.2 Terminal layout and connection specifications................................. 3-14
3.3.3 Switching between sink logic and source logic................................. 3-15
3.3.4 Wiring of the contact input terminals................................................ 3-16
3.3.5 Wiring of the speed command input terminals ................................. 3-17
3.3.6 Wiring of the transistor output terminals........................................... 3-18
3.3.7 Wiring of the contact output terminals.............................................. 3-19
3.3.8 Wiring of the instrument connection terminals.................................. 3-19
3.4 Wiring of the PU Connector 3-20
3.4.1 Pin layout......................................................................................... 3-20
3.4.2 Using the cable to connect the operation panel ............................... 3-20
3.4.3 System configuration examples for communication operations........ 3-20
3.4.4 Wiring methods for communication operation.................................. 3-22
4. HOW TO USE THE OPERATION PANEL 4-1
4.1 Part Names and Functions 4-2
4.2 Operation Modes 4-3
4.3 Operation Procedures 4-4
4.4 Restrictions for Use of the FR-PU04 4-8
5. OPERATION 5-1
5.1 Power On 5-2
5.2 Parameter Setting 5-2
5.2.1 Setting of the operation mode parameter...........................................5-2
5.2.2 Confirmation of the basic operation parameters.................................5-2
Get other manuals https://www.bkmanuals.com

9
5.3 Operation Examples 5-3
5.3.1 PU operation mode............................................................................5-3
5.3.2 External operation mode....................................................................5-4
5.3.3 External/PU combined operation mode 1........................................... 5-5
5.3.4 External/PU combined operation mode 2........................................... 5-6
5.3.5 Starting operation .............................................................................. 5-7
6. TROUBLESHOOTING 6-1
6.1 Message Appearing on the Operation Panel 6-2
6.1.1 Protective function activated.............................................................. 6-2
6.1.2 Alarm function activated.....................................................................6-5
6.1.3 Others................................................................................................ 6-6
6.1.4 Correspondences between digital and actual characters...................6-6
6.2 Motor operation out of ordinary 6-7
6.3 Noise Malfunctions and Measures 6-8
6.4 Maintenance and Inspection 6-10
6.4.1 Inspection........................................................................................ 6-10
6.4.2 Wear parts....................................................................................... 6-12
6.4.3 Cooling fan replacement method..................................................... 6-13
6.4.4 Drive unit replacement..................................................................... 6-14
6.4.5 Measurement of circuit current ........................................................ 6-15
7. SPECIFICATIONS 7-1
7.1 Drive Unit Specifications 7-2
7.1.1 Standard specifications......................................................................7-2
7.1.2 Outline drawings................................................................................ 7-5
7.1.3 Option list...........................................................................................7-7
7.2 Motor Specifications 7-8
7.2.1 Standard specifications......................................................................7-8
Get other manuals https://www.bkmanuals.com

10
8 PARAMETER FUNCTIONS 8-1
8.1 Protection and Editing of the Parameters 8-6
8.2 Selection of the Operation Mode 8-8
8.3 Selection of the Speed Command 8-12
8.3.1 Selection of the analog speed command specifications................... 8-12
8.3.2 Variable-speed operation using contact input signals ...................... 8-18
8.4 Selection of the Control Circuit Contact Input Terminal Functions
8-21
8.5 Setting of the Operation Pattern 8-24
8.5.1 Running speed region...................................................................... 8-24
8.5.2 Acceleration time and deceleration time .......................................... 8-26
8.5.3 Acceleration/deceleration patterns................................................... 8-28
8.5.4 Stopping operation........................................................................... 8-29
8.5.5 Selection of regenerative brake unit................................................. 8-30
8.5.6 Stall prevention operation level........................................................ 8-31
8.5.7 Selection of motor tone.................................................................... 8-32
8.5.8 Other settings .................................................................................. 8-32
8.6 Setting of Various Operation Methods 8-34
8.6.1 JOG operation ................................................................................. 8-34
8.6.2 Communication operation from the PU connector............................ 8-35
8.6.3 PID control operation....................................................................... 8-45
8.6.4 Alarm retry operation ....................................................................... 8-52
8.6.5 Power failure deceleration-to-stop operation.................................... 8-54
8.7 Monitoring of Operation Status 8-55
8.7.1 Selection of operation panel display data......................................... 8-55
8.7.2 Selection of the control circuit output terminal functions................... 8-58
8.7.3 Detection of running speed.............................................................. 8-61
8.7.4 Detection of output current............................................................... 8-63
8.7.5 Selection of the instrument connection terminal functions................ 8-64
8.8 Control Parameters 8-67
APPENDIX 1 PARAMETER LIST (NUMERICAL ORDER) 8-69
Get other manuals https://www.bkmanuals.com

1. PRE-OPERATION INFORMATION
1-1
1
2
3
4
5
6
7
8
1. PRE-OPERATION INFORMATION
This chapter provides fundamental information necessary prior to operation of the drive unit.
 Contents of This Chapter 
Page
1.1 Checking the Product 1-2
1.1.1 Contents............................................................................................ 1-2
1.1.2 Type ..................................................................................................1-2
1.1.3 Drive units to be used with motors..................................................... 1-2
1.2 Parts Identification 1-3
1.3 Handling of the Cover and Operation Panel 1-4
1.3.1 Removal and reinstallation of the front cover..................................... 1-4
1.3.2 Handling of the wiring cover............................................................... 1-4
1.3.3 Removal and reinstallation of the operation panel .............................1-5
1.4 Transportation 1-6
1.5 Storage 1-6

<Abbreviations>
•DU
Operation panel (FR-DU04)
•PU
Operation panel (FR-DU04) or parameter unit (FR-PU04)
•Drive unit
Mitsubishi magnetic motor drive unit
•Pr.
Parameter number
•PU operation
Operation using the PU (FR-DU04/FR-PU04)
•External operation
Operation using the control circuit signals
•Combined operation
Operation using both the PU (FR-DU04/FR-PU04) and
external operation
Get other manuals https://www.bkmanuals.com

1. PRE-OPERATION INFORMATION
1-2
1.1 Checking the Product
Unpack the drive unit, inspect the contents, and check the name plate to ensure that the product
agrees with your order.
1.1.1 Contents
Contents Quantity
Drive unit 1
Specification/instruction manual 1
SAFETY INSTRUCTIONS (seal)* 1
* The SAFETY INSTRUCTIONS (seal) are included in the specification/instruction manual.
1.1.2 Type
Locations of the capacity plate and name plate and definitions of their descriptions
MITSUBISHI
MODEL MELIPM
MITSUBISHI ELECTRIC CORPORATION
MADE IN JAPAN
MD-AX520-0.5K
INPUT :
OUTPUT :
SERIAL :
XXXXX
XXXXX
PASSED
Capacity plate
Name plate
Capacity plate
Drive unit type Serial number
Name plate
Input rating
MD-AX520-0.5K/ Output rating
Serial number
Drive unit type
Type
A X 5 2 0M D - - K
Capacity
Series
Power supply: 3-phase 200V
1.1.3 Drive units to be used with motors
Use the drive units and motors in the following combinations.
(The drive unit and motor of the same capacity are used together.)
Drive Unit Motor
MD-AX520-0.5K MM-CF52
MD-AX520-1.0K MM-CF102
MD-AX520-1.5K MM-CF152
MD-AX520-2.0K MM-CF202
MD-AX520-3.5K MM-CF352
Get other manuals https://www.bkmanuals.com

1. PRE-OPERATION INFORMATION
1-3
1
1.2 Parts Identification
Appearance of drive unit
Capacit
y
plate
POWER lamp
ALARM lamp
Operation panel (FR-DU04)
Brake resistor (Fitted on the back)
Accessory cover
Front cover
Name plate
Without front cover
Wiring cover
PU connector
(Provided with modular jack type relay connector)
(For use with RS-485 cable)
Modular jack type relay connector compartment
Control circuit terminal block
Main circuit terminal block
Get other manuals https://www.bkmanuals.com

1. PRE-OPERATION INFORMATION
1-4
1.3 Handling of the Cover and Operation Panel
1.3.1 Removal and reinstallation of the front cover
Removal
1) Hold both sides of the front cover top and push the front cover down.
2) Hold down the front cover and pull it toward you to remove.
(The front cover may be removed with the PU (FR-DU04/FR-PU04) on.)
Unit
Tab
Front cover
Reinstallation
1) Insert the tabs at the bottom of the front cover into the sockets of the unit.
2) Using the tabs as supports, securely press the front cover against the unit.
NOTICE When reinstalling the cover, fix the tabs securely.
If the removed front cover has the operation panel on it, remove the operation panel
before reinstalling the front cover.
1.3.2 Handling of the wiring cover
Slide the wiring cover toward you to remove.
When cable conduits are not used
Cut the protective bushes of the wiring cover with snippers or a cutter before routing the cables.
Protective bushing
Wiring cover
WARNING
Do not remove the protective bushing. Doing so can scratch the cable sheathes by
the wiring cover edges, causing a short circuit or ground fault.
When cable conduits are used
Remove the corresponding protective bushing and connect the cable conduits.
Get other manuals https://www.bkmanuals.com

1. PRE-OPERATION INFORMATION
1-5
1
1.3.3 Removal and reinstallation of the operation panel
Hold down the top button of the operation panel and pull the operation panel toward you to remove.
ReinstallationRemoval
To reinstall, insert straight and mount securely.
NOTICE Do not reinstall the operation panel to the front cover which has been removed from
the drive unit. Doing so will damage the PU connector.
Reinstallation using the connection cable
1) Remove the operation panel.
2) Disconnect the modular jack type relay connector. (Place the disconnected modular jack type
relay connector in the modular jack type relay connector compartment.)
Modular jack type
relay connector compartmen
t
Modular jack type
relay connector
3) Securely plug one end of the connection cable into the PU connector of the drive unit and the
other end into the operation panel.
Get other manuals https://www.bkmanuals.com

1. PRE-OPERATION INFORMATION
1-6
1.4 Transportation
When carrying, always support the whole drive unit.
1.5 Storage
Store the drive unit in the following environment.
Ambience No corrosive gas, flammable gas, oil mist, dust and dirt.
No exposure to direct sunlight. No salt.
Ambient temperature -10°C to +50°C (non-freezing)
Storage temperature -20°C to +65°C (applies to short-time transit)
Ambient humidity 90%RH or less (non-condensing)
Vibration 5.9m/s2(conformance with JIS C 0040)
NOTICE
If the specification value of humidity is satisfied, condensation and/or freezing will
occur in places where temperatures vary greatly. Avoid storing the equipment in
such places.
Avoid placing the unit directly on the floor. Place it on a stand or shelf.
Get other manuals https://www.bkmanuals.com

2. INSTALLATION
2-1
1
2
3
4
5
6
7
8
2. INSTALLATION
This chapter gives preparatory information on installation and wiring of the drive unit.
NOTICE
The Japanese harmonic suppression guidelines for suppression of harmonics were
established by the Ministry of International Trade and Industries in September,
1994.
To comply with the regulation levels determined by the Japan Electrical
Manufacturers' Association in accordance with the "harmonic suppression guideline
for household appliances and general-purpose products", connect the optional
power factor improving reactor (FR-BEL or FR-BAL).
 Contents of This Chapter 
Page
2.1 Checking the Installation Environment 2-2
2.1.1 Operating environment ......................................................................2-2
2.1.2 Installation in control box................................................................... 2-3
2.2 Preparation of Peripheral Devices 2-5
2.2.1 Basic configuration ............................................................................2-5
2.2.2 Selection of peripheral devices.......................................................... 2-6
2.3 Installation Method 2-9

Get other manuals https://www.bkmanuals.com

2. INSTALLATION
2-2
2.1 Checking the Installation Environment
2.1.1 Operating environment
General operating environment
Install the unit in the following environment.
Ambience Indoors (No corrosive gas, flammable gas, oil mist, dust and dirt
No exposure to direct sunlight. No salt.)
Ambient temperature -10°C to +50°C (non-freezing)
Ambient humidity 90%RH or less (non-condensing)
Altitude Maximum 1000m
Vibration 5.9m/s2(conformance with JIS C 0040)
CAUTION
Install the equipment on a non-flammable material. Not doing so can cause a fire.
Do not place flammable materials near the equipment. Doing so can cause a fire.
Install the unit in a load-bearing place. Not doing so can cause an accident.
Noise environment
Since drive is an electronic piece of equipment, the drive unit may malfunction if there are machines
which generate large noises (e.g. welder, power equipment) in the periphery. Fit surge suppressors,
noise filters and/or like to the noise sources, install the drive unit as far away as possible from noise
sources, or place shielding plates and the like to fully suppress noises.
CAUTION
The drive unit itself can be the source of noises. Take noise suppression measures
to prevent peripheral equipment from malfunctioning due to noises.
Refer to: Chapter 3, 3.1.2 Noises
Chapter 6, 6.3 Noise Malfunctions and Measures
Get other manuals https://www.bkmanuals.com

2. INSTALLATION
2-3
2
2.1.2 Installation in control box
When installing the drive unit in a control box, the internal temperature of the control box must not
exceed the permissible value due to drive-unit generated heat and peripheral-generated heat.
Placing a heat sink outside the control box can reduce the heat generated inside the control box
Refer to: Chapter 7, 7.1.3 Option list (External heat sink mounting attachment)
Measurement positions of ambient temperatures
5cm 5cm
5cm Measurement position
Drive unit Measurement position
Layout of drive units within control box
V
entilation fan
Drive unit
(Correct example) (Incorrect example)
Drive unit
Position of ventilation fan
Built-in cooling fans
Accommodation of two or more drive units
Drive unit Drive unit Drive unit
Drive unit
(Incorrect example)(Correct example)
NOTICE
Leave the specified clearances between the drive unit and control box walls or other
equipment. Not doing so can cause a failure. In addition, improper convection of air
in the control box will reduce the heat dissipation effect. Fully consider the
equipment layout in the control box and the use of a cooling fan for ventilation, for
example.
10cm
or more
1cm
or more
Drive unit 1cm
or more
These clearances are also required for
replacement of the cooling fan.
Leave sufficient
clearances above and
under the drive unit
to ensure adequate
ventilation.
Cooling fan built
in the drive unit
Cooling air
10cm
or more
Get other manuals https://www.bkmanuals.com