Mixx Integrated 10 Administrator Guide

Integrated 10
Powerbank
WITH BUILT-IN CABLES
HOW TO GUIDE

THANKS!
Thanks for choosing our MIXX Integrated 10 Powerbank.
All of our products come with a 2 year warranty
for peace of mind.
Feedback is welcome,
email us on
[email protected]
for any comments or
queries.

CONTENTS
HOW TO GUIDE EN
LET’S START 1
LET’S POWER 3
LET’S CHARGE THE INTEGRATED 10 4
LET’S CHARGE YOUR DEVICE 5
NEED EXTRA HELP? 7
CONTACT MIXX 8
LET’S VIEW TECHNICAL SPECS 8
LET’S BE SAFE 9
LET’S RECYCLE 10
SAFE USAGE INFO 13

1 2
What’s in the box?
LET’S START
A MIXX Integrated 10 Powerbank
7
1
2
3456
8

1 2 HOW TO GUIDE EN
Power Button
Micro USB Input Port
Lightning USB Output cable
USB C Output cable
Micro USB Output cable
USB A Input cable
USB A Output Port
LED Charge Indicators
1
2
3
4
5
6
7
8

3 4
Press the Power Button [1] to turn your
MIXX Integrated 10 Powerbank on.
LET’S POWER
1
8
1

3 4
Connect the Powerbank to a suitable USB wall charger
or a computer USB port using the built-in USB A power
cable [6] and your Integrated 10 will start charging.
Alternatively, you can use a Micro USB cable (available
separately) and plug into the Micro USB Port [2] to power
the Integrated 10.
If there is no phone or device detected to charge, the
Powerbank will turn off automatically after 30 seconds.
When all 4 LED lights [8] are solid WHITE the Powerbank
is fully charged.
Check the battery status
Each of the 4 LED lights [8] on the Integrated 10
Powerbank represents 25% charge (from left to right).
Each LED light [8] will turn off as the battery level falls
below that percentage of charge. After each of the LED
lights have gone out and only the first is left on, the
Powerbank is down to 25% charge.
This first LED light will flash WHITE when the battery is
lower than 25% charge and turn off once the battery is
depleted.
When all 4 LED Charge Indicators have switched off, it is
time to recharge the Integrated 10.
HOW TO GUIDE EN
8
8
LET’S CHARGE THE
INTEGRATED 10
6
2
8

5 6
LET’S CHARGE YOUR DEVICE
4
53
1

5 6
Simply plug your device into the Powerbank using the
cable with the correct connector, your device will start
to charge and you should see your devices usual battery
screen or icon as confirmation. If it does not begin
to charge, press the power button [1] to turn on the
Powerbank.
You can use all three Output cables to charge three
different devices at the same time if required.
Using the built-in cables
You can charge your mobile devices and accessories
using the built-in Micro [5] , USB C [4] and Lightning [3]
Output cables.
HOW TO GUIDE EN
LET’S CHARGE YOUR DEVICE
3
45
1

7 8
NEED EXTRA HELP?
Common solutions
If you are experiencing problems with your Powerbank:
• Switch on the Powerbank (see page 3)
• Check if the Powerbank is charged (see page 4).
FAQS
Q. How long will it take to charge the MIXX Integrated 10
Powerbank?
A. The charge time will vary depending on the power
output of your charger.
For a 10,000mAh capacity power it will take up to 6 hours.
Q. My device is not fast charging with the Powerbank?
A.
• Make sure you are using the correct cable connector for
your device.
• Unplug your device from the Powerbank and wait for the
Powerbank to turn off after 30 seconds before trying
again.