MJX HYPER GO 16207 User manual

No.16207 14+
1:16 RC HIGHSPEED CAR
USER MANUAL

!
Safety Precautions
In order to operate the car safely. Be sure that you have observed
the following points:
●It is a radio control model, not a toy!
●In order to enjoy running the car, you need to finish assembly before operation. Do routine maintenance
work after operation. Replacement parts and option parts are available separately.
●Improper usage with Alkaline cells or rechargeable batteries may damage the electronics for the car or
the radio.
Please follow the points as below in order to prevent accident from happening to the car and
people.
Precautions for Battery Use
1. Transmitter uses 2x1.5V “AA” batteries.
2. Please pay attention to correct polarity when replacing batteries.
3. Rechargeable batteries should be charged under adult supervision.
4. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable
batteries.
5. After the battery is exhausted, the model should be removed.
6. Exhaust battery should be safety dispose!
7. DO NOT short circuit any terminals.
8. DO NOT attempt to recharge non rechargeable batteries.
9. Remove batteries from the model when charging.
10. DO NOT put batteries into a fire or into water.
11. The rated input voltage battery charger MUST be suitable for your mains power voltage.
12. During charging it is quite normal for the charger and batteries to heat up.
13. Do not swallow battery!
14. Store only in cool, dry and dark places and should be keep out of the children!
15. When the battery leaks the liquid and let it into you eyes, please right away rinse them and consult
an ophthalmologist.
The instruction sheet for this product is just for your reference. We reserve the right to make changes
or adjustments on the product without prior notification. Please refer to the official information.
Warning:
Choking hazard! This product contains small parts. NOT suitable for children under 3 years. Contains
electrical components and should be kept dry at all times. Regularly check the battery charger wires,
plugs and shell and other components for damage. DO NOT use if any part is damaged.
Warnings & Cautions
1. Detachable small parts should be stored safely and out of reach of children.
2. If interference is experienced, turn the model off and try it again in a different area.
3. Transmitter will not function correctly if the batteries are low. Please replace the batteries.
4. Please discard old/used batteries in a safe manner. Consider your environment!
5. Please store the remote control model in cool, dry place.
6. DO NOT expose to fire or high temperatures, do not store in moist place.
7. Once the battery get wet, wipe immediately with a soft dry cloth.
If the battery any deformation, please stop using.
8. If you don’t use the model for a long time, please raise the chassis to let the wheels hang in the air.
-1-

!Do NOT operate the model in the following places and situations.
(Non-observance may lead to accident!)
Operating Your Model Safely
●Operate your model in spacious and safe areas! Do not operate it:
1. On road!
2. In places where children and many people gather.
3. In residential districts and parks!
4. Do not operate the model on public roads, in crowded places and near infant as it may cause
accidents.
5. Indoors and in limited space! Non-observance may result in personal injury and property damage!
●The car must stop immediately and check for the reasons when it is operating abnormal.
As long as the problem is not cleared, do NOT operate it! This may lead to further trouble and
unforeseen accidents!
●Always check the radio batteries!
With weak dry batteries, transmission and reception of the radio would fall off. You may lose control
of your model in such condition. This may also cause serious accidents!
●Keep in mind that people around you may also operate a radio control model!
NEVER share the same frequency with somebody else at the same time! Otherwise, Radio signals
will be mixed up and you will lose control to your model. This may lead to accidents.
●Do NOT put fingers or any objects inside rotating and moving parts!
●Right after use, do NOT touch the motor! Danger of burning yourself!
●When the model is not in use, always turn off the receiver and transmitter. Further more, disconnect
the batteries and remove them from the model and the transmitter. This may be dangerous such as
overheat and leakage.
●Be sure to read thoroughly
the manual before you
begin. Fresh user should
seek advice from people
having rich experience in
order to assemble the
model correctly.
●Cutters, nippers and
screwdrivers need careful
handling.
●Do not expose this model
to high temperature, humidity
or direct sunlight.
●Never reverse connection/
disassemble the battery.
This may lead to damage
and leakage.
●As the product contains
small and sharp parts,
assemble and store this
product only in places
out of the reach of children.
-2-

FCC PART 15 B Notice:
CAUTION
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
-3-

Power Switch
1. Turn on the power switch of the transmitter, the signal indicator light of transmitter flashes.
2. Press the power button of high speed car, which is on the side of the ESC; the indicator light of high
speed car flashes.
3. When the indicator light stays on, the high speed car can be operated to play.
!●When turn on the transmitter, please DO NOT touch the throttle and steering. After turn on the
transmitter’s power, please operate after the indicator light of transmitter staying on.
●Please comply the principle of “turn on the transmitter firstly, then turn on the high speed car’’.
●In the frequency matching, please make sure there is only one pair of transmitter and high speed
car in matching at the same time, otherwise the frequency will match wrongly.
R30 Receiver
!Warning: Please make sure the connection is correct.
VCC/FAN
VCC/FAN
CH3
CH2
CH1
VCC/FAN
VCC/FAN
CH3
CH2
CH1
Antenna
(Please make sure it in
vertical direction)
Stays on Signaled
R30 Indicator
situation Meanings
Flashes No Signal
VCC/FAN: Power Interface (VCC=5-6V)
ESC
(CH2)
Steering
servo
(CH1)
Fan
(VCC/FAN)
R30
-4-

T3B Transmitter
①ST.TRIM
(Steering servo strimmer)
②TH.TRIM (Throttle trimmer)
③Power switch
(OFF-70%TH-100%TH)
④Indicator light
⑤ CH1: ST (Steering)
⑥ CH2: TH (Throttle)
⑦CH3: Fn
If the car cannot go straightly during driving, it can
be adjusted through the ST.TRIM.
①ST.TRIM (Steering servo strimmer)
!Please Do Not forcible/reversely insert all sockets.
E45A Brushless ESC
Stays on Signaled
E45A Indicator
light situation Meanings
Flash quickly a. No signal
b. Pull the trigger
Flash slowly Low voltage
Flash twice Over heat
protection
Off Stuck protection
Indicator
VCC/BVD
Yellow wire A
Blue wire C
White wire B
Power switch
Heat sink
VCC: Powered by battery circuit. Please provide the same voltage as the connected battery. It can be used
as cooling fan power power. Please make sure the battery voltage of the ESC is in the range of fan’s.
BVD: Receivers with BVD function can be directly connected to this interface through an adapter cable, which
is equivalent to connecting a battery.
If the car can’t be stop when the TH in the
middle place, you can adjust the button to
stop the car.
②TH.TRIM (Throttle trimmer)
Forward
-5-

70%
(70% Throttle)
OFF 100%
(100% Throttle)
Flash quickly Frequency mating
Stays on Working well
Flash slowly Low battery of transmitter
③Power/Speed switch ④Indicator light
⑤CH1: ST (Steering)
Middle Turn left Turn right
⑥CH2: TH (Throttle)
Forward
Brake: When the car is going forward, pull the transmitter trigger back,
and the car enters into the braking state. After the trigger is in the
middle, push back again, and the car can move backward.
*When the car is in reverse situation, it does not the brake function.
Backward
Middle
Push
forward
Pull
back
Pull
back
-6-

Install the Head Wheels
Fix the head wheels into
the rear of the car via 3
screws.
Install the tail to the body, lock with 2 screws.
Install the Tail
Install the Transmitter’s Battery
Open the transmitter’s battery cover, insert 2 AA batteries according to the indicated positive and
negative direction, close the battery cover.
-7-

Adapter 5V2A
(Sold separately)
Install Battery and Charge Battery
①Turn the battery lock knob and flip up the cover;
②Connect the receiver plug to the battery;
③Put the battery into the battery holder and make sure it is in place;
④Flip back the cover and turn the knob to lock it.
Install the battery
High speed car battery: 11.1V 1050mAh 25C.
If charging with a 5V 2A USB adapter, the charging time is about 240 minutes.
●When charging, the indicator light of charger is green and flashes;
●When the battery is fully charged, the green indicator light of the charger stays on.
*The above charging time data is based on the test result of 5V 2A adapter. Using different specifications
of adapters or power supply equipment will affect the actual charging time. It is recommended to use a
5V2A adapter for charging.
Charge
-8-

Install Car Shell
1. Aline the 3 holes of the car shell with holders, then install it.
2. Insert the 3 clips into the holes to lock the car body.
-9-

16200
R168Z 2PCS
Ball bearing
Bearing:
M26124
16230
M26124
R168Z
16220
Q1601
16210
Q1601
R168Z
M26124 2.6x12.5mm 2PCS
Countersunk flat
head screws
Screw:
Pivot balls:
Q1601 2PCS
Steering pivot balls
16200 Front Swing Set
16202
16202 Rear Swing Set
R168Z 2PCS
Ball bearing
Bearing:
M23124 2.3x12mm 1PCS
Countersunk flat
head screws
Screw:
Pivot balls:
Q1602 1PCS
Steering pivot balls
Rear hub pins:
M2523 1PCS
Rear hub pins
M23124
R168Z
Q1602
M2523
16250
R168Z
16260
16240B
Screw:
M21035 2x10mm 1PCS
Countersunk flat
head screws
16405
16402 R168Z
16404
R1810
M21035
16403
16401
R168Z 2PCS
Ball bearing
Bearing:
R1810 2PCS
Ball bearing
16400
16400 Metal Gears Main Driving Set
-10-

Metal Oil Filled Shocks
Add shock oil
16510 (Front)
16500 (Rear)
Spin the suspension adjuster to
adjust the shock absorbers’strength.
Shock absorbers adjuster
M2123 2x12mm 4PCS
Countersunk flat
head screws
R1810 2PCS
Ball bearing
Bearing:Screw:
M2525 2.5x2.5mm 1PCS
Hexagon socket
machine screw
16420 Metal Gears Diff Assembly
M2123
R1810
M2123
R1810
M2525
16420
16700 Servo Assembly
M26126 2.6x12mm 1PCS
Screws
Screw:
16700
M26126
16702
16701
-11-

16430S Steering Assembly
16432
M2665
M23124
M23124
16433 16433
16431
16431
16434
16430S
Screw:
M2665 2.6x6.5mm 2PCS
Step flat screws
M23124 2.3x12mm 3PCS
Countersunk flat
head screws
B284C & 16397C
Motor Assembly
M3030
16393/16393B
B2845
16392B
M25845/M3066
16395C
16397C
M31256
M31256 3x12.5mm 2PCS
Machine screws
M25845 2.5x8mm 2PCS (16393)
Countersunk flat
head screws
Screw:
M3066 3x6mm 2PCS (16393B)
Countersunk flat
head screws
M3030 3x3mm 1PCS
Hexagon socket
machine screw
-12-

M26104
M2684
M2664
M2384
M23114
16150
16130
M2384
E45A
16400 16420
16420
16430S
B284C &
16397C
16140
16700
16270
M23104
M23104
M26104
M26104
16160
16190
High Speed Car Assemble
M23114 2.3x11mm 1PCS
Countersunk flat
head screws
M2684 2.6x8mm 4PCS
Round head screws
M23104 2.3x10mm 6PCS
Round head screws
M26104 2.6x10mm 10PCS
Round head screws
M2664 2.6x6mm 2PCS
Round head screws
M2384 2.3x8mm 4PCS
Round head screws
Screw:
-13-

High Speed Car Assemble
M25425
16170
M26154
M1640A
M25425
M23124
16200
16180
16282
16282
M2684
M2684
M2684
M3294
16410
M23104
M3294
M26104
1612B
16202
M25425 4PCS Lower swing arm fixed shaft Iron shaft:
M2684 2.6x8mm 6PCS Round head screws M23104 2.3x10mm 4PCS Round head screws M3294 3x29mm 4PCS Round head half thread screws M23124 2.3x12mm 1PCS (2PCS) Countersunk flat head screws Screw: M26104 2.6x10mm 4PCS Round head screws M26154 2.6x15mm 1PCS Countersunk flat head screws
-14-

M26645
1611A
16510
1610A
M23124
M26154
M2684
M26645
M23124
16500
High Speed Car Assemble
M2684 2.6x8mm 2PCS Round head screws M26154 2.6x15mm 2PCS Countersunk flat head screws M26645 2.6x6mm 6PCS Countersunk flat head screws Screw: M23124 2.3x12mm 4PCS (8PCS) Countersunk flat head screws
-15-

M40
16300C
16440
M20101
16440 1PCS (4PCS)
Wheel hex
M40 1PCS (4PCS)
M4 Wheel lock nut
Nut:
M20101 1PCS (4PCS)
Wheel hex pins
Iron shaft:
High Speed Car Assemble
-16-

Chassis Parts
16130
16170
1611A 16120S1610A
Rear Bumper (Metal) Wheelie Bar Assembly
16282
F/R Body Pillars
Tail
1612B
16190
1601G
Body
16160
1615016140
Battery Clip Chassis
Front Shock Tower
Front Upper Gearbox
Covers
16180
Rear Shock Tower
Rear Upper Gearbox
Covers
Spare Parts
1622016210 16230
Steering Block
Front Lower Suspension
Arms (Including Ball Head)
Front Upper Suspension
Arms (Including Ball Head)
Front Bumper Assembly
(Metal)
-17-

16440
M20101
Wheel Hex Pins
(8PCS)
Wheel Hex
M1640A
Rear Reinforced Sheet
16300C
16240B
Spare Parts
Rear Upper Suspension
Arms (Including Ball Head) Rear Hubs
16260 M25425
F/R Lower Suspension
Arms Hinge Pins
16250
Rear Lower
Suspension Arms
Metal F/R CVD Shafts
(2 Sets)
16410
Wheel Assembly
(2PCS)
M40
M4 Wheel Lock Nut
(8PCS) Servo
16701 16702
Servo Saver Assembly
16430S
Steering Assembly
16431 16432 16270
Steering Linkage
(2PCS) Connecting Rod ESC/REV Fix Frame
-18-

16393/16393B
Motor Guard
Receiver
R30 16500
Metal Oil Filled Shocks
(Rear)
16392B
Motor Pinions
B2845
Brushless Motor
Motor Assembly
B284C
16510
Metal Oil Filled Shocks
(Front)
Motor Fan
16397C
16395C
Motor Heatsink
Spare Parts
Metal Gears Diff
Assembly
16420
Spur Gear Assembly
(Metal)
16401
ESC
E45A Brushless ESC16403
Centre Drive Shaft
16402
Drive Gear
(Metal)
T3B
Transmitter
Metal Gears Main
Driving Set
16400
-19-