MK Elements Collection User manual

MK Elements Collection
Electronic Dimmer
Installation Guide
Fitting and removing frontplate
Locate top hooks on front plate
to top edge of module.
Lower front plate,locating
hooks on sides and bottom
edge.
Carefully insert a 4mm
screwdriver into the slots
provided along the bottom edge
of the frontplate.
Carefully twist the screwdriver
and lift the frontplate away
disengaging the snap ts.
Fitting the frontplate Removing the frontplate
2
2
11
Note:
1. A 2-Way switching installationmay not work with a Mechanical 2-Way
Switch, if incorporating an electric powered indicator (e.g.LED or neon)
2. Additional neutral wire is required on certain load types and 2-Way
switching congurations.
3. The cable length between the two end point products must not exceed
40m, and the minimum cable size of 0.75mm².
4. When an Elements Electronic Dimmer is used as a 2-Waycontrolling device, both
device must be of the same type. Do not mix dierent dimmer types i.e. leading
edge and trailing edge.
5. Not applicable to K34499.
Conventional 3-Wire
2-Way wiring
1 2 1 2
Common Common
2-wayswitches
Dottedlines show alternative switch positions
N
L
SW.L
Lamp
2- Wayinstallation with
Elements 1 Gang
Electronic Dimmer and
2-Way Mechanical Switch
L
N
1
R1
1
2
C
Elements 1 G ang
Electroni c Dimmer
Existing3-wire
2-waywiring
Referto load
typetable
forneutral
requirement
Load
Live
2-Way
MechanicalSwitch
L
N
1
R1
1
2
C
Elements 1 G ang
Electroni c Dimmer
Referto load type
table for neutral
requirement
Load
Live
2-Way
MechanicalSwitch
Unusedwire.
Terminateboth ends appropriately.
2-Way installation with
any 2 Elements 1 Gang
Electronic Products
L
N
1
R1
L
N
1
R1
*Elements 1 G ang
Electroni c Dimmer/Switch
Elements 1 G ang
Electroni c Dimmer
Existing3-wire
2-waywiring
Neutral
Load
Live
2-Way installation with
Elements 1 Gang
Electronic Dimmer and 2-Way
Mechanical Switch
Conventional 2-Wire
2-Way wiring
1 2 12
Common Common
2-wayswitches
Dottedlines show alternative switch positions
N
L
Lamp
2-Way installation with
any 2 Elements 2 Gang
Electronic Products
L
N
1
R1
L
N
1
22
R1
R2R2
*Elements 2 Ga ng
Electroni c Dimmer/switch
Elements 2 Ga ng
Electroni c Dimmer
Existing3-wire
2-waywiring
1. *Neutral is mandatory on the controlling electronic device.
2. If multi core cable is used, do not run R1 & R2 wires in the same multi core cable.
3. Refer to note 4 in this section for type of dimmer to be used.
Importantnotes:
Neutral
Load1
Load2
Live
1
2
C
L
N
1
R1
Elements 1 G ang
Electroni c Dimm er Existing 2-wire
2-waywiring
Referto load
typetable
forneutral
requirement
Load
Live
2-Way
Mechanica l Switch
2-Way installation with
any 2 Elements 1 Gang
Electronic Products
2-Way installation with
any 2 Elements 2 Gang
Electronic Products
L
N
1
R1
L
N
1
R1
Elements 1 G ang
Electroni c Dimmer
Elements1 Gang
Electronic
Dimmer/Switch
Existing2-wire
2-waywiring
*Neutral
Referto load type
tablefor neutral
requirement
Live
Load
L
N
1
R1
L
N
1
22
R1
R2 R2
Elements 2 Ga ng
Electroni c Dimmer
Elements 2 Ga ng
Electroni c Dimmer/
Switch
Existing2-wire
2-waywiring
*Neutral
Live
Load2
Load1
Importantnotes:
1.*Neutral is mandatory on the controlling electronic device.
2. If multi core cable is used, do not run R1 & R2 in the same multi core cable.
3.Refer to note 4 in this session for type of dimmer to be used.
L
N
1
R1
1
2
C
Elements1 Gang
ElectronicDimmer/Switch
Existing2-wire
2-waywiring
Referto load
typetable
forneutral
requirement
Load
Live
2-Way
mechanica l Switch
These wiring diagrams represent common 2-Waywiring options, for more visit
www.mkelectric.com.
For neutral connection to the Dimmer,refer to the specications for load types
that require a Neutral connection. If these loads are used without a Neutral
connection, the dimmer and lamp may not operate correctly.
For Mounting Boxes,the minimum depth required is 35mm. When using 2.5mm²
cables the minimum box depth required is 40mm.
Note:
When carrying out insulation resistance testing, rst disconnect the product.
Failing to do this could damage the product and couldalso give spurious
insulation readings.
Note:
Upon attaching new frontplate, the indication on the product may show erratic
operation i.e. rapid ashing.This is normal as the product is adapting the new
frontplate.This process may take up to 20 seconds.
Note:
In a single lamp installation it is recommended to connect neutral to the
electronic dimmer.
Installing the product
Installation & safety instructions
This product must be installed by a competent person (e.g. a qualied electrician) in
accordance with these instructions and the appropriate current national wiring
regulations. (e.g. the IEEWiring Regulations BS 7671)
While working on any appliance, turn o the mains supply to make sure that
appliance is not live. Before changing a lamp or bulb ensurethe elec tricity supply to
the lamp holder or light tting is o.
Do not use electric screwdrivers or power tools to tighten the product.
The mains supply to dimmer must be protected by a type‘B’ or ‘C’MCB with rating
not higher than 10A.
Before starting the appliance, make sure that all connections are as per the
instructions, the cables are not stressed and the terminals are fully tightened.
Toprevent re hazard, do not exceed the rated load specied for the appliance.
Do not install the appliance in bathrooms, washrooms or any location subjected to
splashes of water,condensation or dampness.
How to install
Toensure safe installation, you must read all the installation & safety instructions
on page-1, and refer to the wiring diagrams on page-4.
Installation
1. Ensure the depth of the back box is correct for the product and that it is tted
securely to the wall.
2. Install the cables in the normal way and, using the xing screws supplied,
mount the product, still minus its frontplate, to the wall.I t is important the
correct headed screws are used as any other may clash with the rear of the
frontplate.
3. Do not over tighten the screws, so as to preventdamage or distortion to the
product or support frame. Adjust so the frame or module sits squarely on the
wall.
4. Fit the frontplate as shown on page-3.
1 2
Refer to these wiring diagrams for 1-Wayand 2-Way switching installations.
Elements Leading & TrailingEdge Dimmers can be controlled remotely by a
2-Way Mechanical Switchor an Elements Elec tronicDimmer or Switch, if
connected to its control port by the existing 2-Waywir ing in the installation.
Electronic Dimmer: 1-Way Switching Installation
L
N
1
R1
R2
2
Live
Load2
Neutral
Load1
Referto load
typetable
forneutral
requirement
Leading & Trailing
Edge Dimmers
Fluorescent Dimmer
L
N
1
+
-
Live
Neutral
connection
ismandatory
Neutral
Lamp
Analogue
Dimmable
Ballast
L
N
+
-
Electronic Dimmer: 2-Way Switching Installation
Wiring diagrams
4 5 6 7 8
Electronic Dimmer: 3-Wire 2-Wayswitching installation
Electronic Dimmer: 2-Wire 2-Wayswitching installation
3
by Honeywell
Unusedwire.
Terminateboth
endsappropriately.

Note:
1. Overload is indicated by the ring indicator ashing once every 3 seconds.
2. The Electronic Dimmer will resume normal operationonce the overload is
removed, by switching o and on.
Soft start operation
When the Electronic Dimmer is switched on, light levels gradually reach the
desired level over a period of 1 to 3 seconds, greatlyextending life expectanc y of
lamps by avoiding initial power surge.
Overload protection
If the Electronic Dimmer is overloaded input to lamp(s) will be reduced (or
switched o if overload is severe) to protect the device and the installation.
Maintenance
Cleaning
Please clean the device with a dry and soft lint free cloth.
Do not use water or any abrasive solvent based or aerosolcleaners as this may
damage, discolor or aect the nish and safety of the appliance.
Features Powerfailure recovery
In case of power failure, the dimmer will restore toits previous state upon
power restoration.
Minimum brightness adjustment
The User can adjust the minimum brightness level to suit their environment
and ensure optimum lamp performance. See User Guide for programming
details.
9 10 11
Trailing Edge Dimmers K34103
GLS/Tungsten lament,
MainsTungsten Halogen 25 – 500W
ELVTungsten Halogen with
Dimmable Electronic Transformer 35 – 500VA
K34104 & K34105(Per gang)
25 – 300W
35 – 300VA
Dimmable LED Driver *4-150W
(Max5 LED drivers only)
*4-120W
(Max5 LED drivers only)
Neutral connection is mandatory on 1-10V Dimmer. Suitable for use with
dimmable uorescent or LED lighting which is driven by separate 0/1-10V
control gear.
Suitable for use with 0/1-10V analogue dimmable ballast operating in accordance
with IEC60929 annex E.
Note: This product is only suitable foruse with ballasts which are the source of the
control voltage. It is not suitable for any other load type.
1-10V Dimmer K34499
Rated Load 6AX
Maximum number of ballasts 10
Standard compliances
The products in this range comply with IEC 60669-2-1 and the following EC:
• LowVoltage Directive (73/23/EEC)
• ElectromagneticCompatibility Directive (89/336/EEC)
• Restrictedof Hazardous Substances (2011/65/EC)
Warranty
• The Company undertakes to replace or repair, at its discretion, this product
should it become defective within a period of 20 years after delivery (5 years for
mains related electronic products), solely as a result of faulty materials and/or
workmanship. Understandably,if the product has not been installed or
maintained in accordance with the Company’sinstructions, has not been used
appropriately, or if anyattempt has been made to rectify, dismantle or alter the
product in any way,the warranty will be invalidated. This warranty states the
company’sentire liability. It does not extend to cover consequential loss or
damage or installation costs arising from the defective product. This warranty
does not restrict or infringe the normal statutory rights of the consumer.
• MKElectric wishes to make it clear that it owns all original designs of the
products which it manufactures (whether or not listed in this leaet) and that it
will take all necessary legal action in any part of the world against any party
found to be manufacturing, distributing, selling or otherwise dealing with any
article which infringes the company’s intellectual property rights in its products,
or any other right of the company therein.
Disposal
Product and packaging should be disposed o via standard refuse facilities at the
end of its useful life. Where ever possible packaging and components should be
recycled.
Technical Help
Tel:
Fax:
[e-mail]
Technical Help
Tel:
Fax:
[email protected]
[phone]
[phone]
[phone]
[phone]
Customer Service
Tel: [phone]
Fax: [phone]
Fax: [phone] (International)
[e-mail]
Customer Service
Tel: [phone]
Fax: [phone]
Fax: [phone] (International)
[email protected]
MK Electric
The Arnold Centre, PaycockeRoad,
Basildon, Essex SS14 3EA. UK
www.mkelectric.com
All marks in this document identied with ® or ™
symbol adjacent to the mark are trademarks of MK Electric Ltd.
©Honeywell International Inc.
50081614-001 Rev.A
MK Electric
The Arnold Centre, PaycockeRoad,
Basildon, Essex SS14 3EA. UK
www.mkelectric.com
All marks in this document identied with ® or ™
symbol adjacent to the mark are trademarks of MK Electric Ltd.
©Honeywell International Inc.
50081614-001 Rev.A
Load rating & type
Leading Edge Dimmers K34100
GLS/Tungsten lament,
MainsTungsten Halogen 40 - 500W
Mains dimmable LED lamp for
incandescent replacement 6 - 150W Max.12lamps
ELVTungsten Halogen with
dimmable Ferro-magnetic transformer 35 - 400VA
K34101 & K34102 (Pergang)
40 – 300W
6 - 120W
Max.12 lamps
35 - 240VA
Product specications
Nominal mains supply voltage 220 to 240V a.c.
Max. acceptable mains uctuation 198 to 264V a.c.
Mains frequency 50/60Hz ± 3Hz
Ambient temperaturerange 0°C to 45°C
Other information
Troubleshooting
Unable to t frontplates to module
Please check if you are tting the correct frontplate to the correct module.The
frontplate must match the module exactly,e.g. 1 Gang Electronic Dimmer Frontplate
will only t a 1 Gang Electronic Dimmer Module. Please refer to the instructions for
tting and removing frontplates on page-3.
Connected Lamp does not turn ON or DIM
Firstly check the lamps have not expired.
Check connections and wiring to the device to ensure it has been
installed correctly.
Check the circuit, by inspecting other devices on the same circuit, to
ensure there is power input to the device.
Ring indicator ashes once every 3 seconds
This is indication of an overload.The Electronic Dimmer will resume normal
operation once the overload is removed,by switching o and on.
If you are facing a problem not listed here, please contact the MK technical team.
(Contact details are listed on the last page)
Notes:
1. Do not use loads of dierent types on the same circuit.
2. Not suitable for use with any other load type.
3. *Neutral connection is required. It is recommended toconnec t neutralwhenever possible to
extend the load handling capability of the dimmer.
12 13 14 15
(Not applicable to K34499)