ML Accessories Knightsbridge OS008 Instruction Manual

116
INSTALLATION & MAINTENANCE MANUAL
OS008
IP
20
230V
50Hz
1

These instructions should be read carefully and retained after installation by the end user for future
reference and maintenance.
These instructions should be used to aid installation of the following product:
OS008
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this sensor should only be carried out by a qualified electrician or competent person
to the latest Building and current IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit does not exceed the rating of the circuit cable, fuse or circuit
breaker
• Please note the IP (Ingress of Protection) rating of this sensor when deciding the location for
installation
• This product should be installed into an insulated enclosure or luminaire to complete a class II
rating
• This product is IP20 rated
• Provide power to the required point of installation. Suitable IP rated junction boxes should be
used where required
• We recommend a mounting height of 1.8m to 2.5m inside a luminaire
• Connect the sensor to the luminaire and mains supply via push-fit connectors ensuring the
correct polarity is observed (see Fig 1)
• Switch on power supply and check for correct operation
Fig 1
OS008
Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand
maintenance.
Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproduct:
OS008
SAFETY
• Installationofthissensorshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe
latestBuildingandcurrentIEEWiringRegulations(BS7671)
• Pleaseisolatemainspriortoinstallation/maintenance
• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe
circuitcable,fuseorcircuitbreaker
• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation
• ThisproductisClassIIdoubleinsulated
• ThisproductisIP20rated
INSTALLATION
• Providepowertotherequiredpointofinstallation.SuitableIPratedjunctionboxesshouldbeusedwhere
required
• Werecommendamountingheightof1.8mto2.5m
• Connectthesensortotheluminaireandmainssupplyviapushfitconnectorsensuringthecorrectpolarityis
observed(seeFig1)













Fig1

• Switchonpowersupplyandcheckforcorrectoperation
SENSORLAYOUT




Live(brown)
L’NLN
Neutral(blue)
Load/
luminaire
Dipswitches
S1toS6
Microwave
sensor
Mains
connections
2

SENSOR LAYOUT
DIP SWITCH LAYOUT
DISTANCE SETTING
Note: We recommend a mounting height of between 1.8 to 2.5m. The table below shows
sensitivity distance in ideal conditions.
This can be set to ‘on all the time
(24hrs)’ or to a specific lux level
Time setting
Lighting control settings
Note: Switch on is Position I and off is Position 0
Fig 2
OS008
Theseinstructionsshouldbereadcarefullyandretainedafterinstallationbytheenduserforfuturereferenceand
maintenance.
Theseinstructionsshouldbeusedtoaidinstallationofthefollowingproduct:
OS008
SAFETY
• Installationofthissensorshouldonlybecarriedoutbyaqualifiedelectricianorcompetentpersontothe
latestBuildingandcurrentIEEWiringRegulations(BS7671)
• Pleaseisolatemainspriortoinstallation/maintenance
• Checkthetotalloadonthecircuit(includingwhenthisluminaireisfitted)doesnotexceedtheratingofthe
circuitcable,fuseorcircuitbreaker
• PleasenotetheIP(IngressofProtection)ratingofthisluminairewhendecidingthelocationforinstallation
• ThisproductisClassIIdoubleinsulated
• ThisproductisIP20rated
INSTALLATION
• Providepowertotherequiredpointofinstallation.SuitableIPratedjunctionboxesshouldbeusedwhere
required
• Werecommendamountingheightof1.8mto2.5m
• Connectthesensortotheluminaireandmainssupplyviapushfitconnectorsensuringthecorrectpolarityis
observed(seeFig1)













Fig1

• Switchonpowersupplyandcheckforcorrectoperation
SENSORLAYOUT




Live(brown)
L’NLN
Neutral(blue)
Load/
luminaire
Dipswitches
S1toS6
Microwave
sensor
Mains
connections

DIPSWITCHLAYOUT








Note:SwitchonisPositionIandoffisPosition0
Distancesetting
Note:Werecommendamountingheightofbetween1.8to2.5m.Thetablebelowshowssensitivitydistanceinideal
conditions.
S1
S2
Distance
S1
S2
Distance
0
0
2m
I
0
6m
0
I
4m
I
I
8m

Timesetting
S3
S4
Time
S3
S4
Time
0
0
8sec
I
0
8min
0
I
3min
I
I
12min

Lightcontrolsetting
Thiscanbeadjustedfromonallthetime(24hr)oronataspecificluxlightinglevel
S5
S6
Light
S5
S6
Light
0
0
24hr
I
0
30lx
0
I
50lx
I
I
10lx











On
S1
S2
S3
S4
S5
S6
PositionI
Position0
Distance
Time
Light

DIPSWITCHLAYOUT








Note:SwitchonisPositionIandoffisPosition0
Distancesetting
Note:Werecommendamountingheightofbetween1.8to2.5m.Thetablebelowshowssensitivitydistanceinideal
conditions.
S1
S2
Distance
S1
S2
Distance
0
0
2m
I
0
6m
0
I
4m
I
I
8m

Timesetting
S3
S4
Time
S3
S4
Time
0
0
8sec
I
0
8min
0
I
3min
I
I
12min

Lightcontrolsetting
Thiscanbeadjustedfromonallthetime(24hr)oronataspecificluxlightinglevel
S5
S6
Light
S5
S6
Light
0
0
24hr
I
0
30lx
0
I
50lx
I
I
10lx











On
S1
S2
S3
S4
S5
S6
PositionI
Position0
Distance
Time
Light

DIPSWITCHLAYOUT








Note:SwitchonisPositionIandoffisPosition0
Distancesetting
Note:Werecommendamountingheightofbetween1.8to2.5m.Thetablebelowshowssensitivitydistanceinideal
conditions.
S1
S2
Distance
S1
S2
Distance
0
0
2m
I
0
6m
0
I
4m
I
I
8m

Timesetting
S3
S4
Time
S3
S4
Time
0
0
8sec
I
0
8min
0
I
3min
I
I
12min

Lightcontrolsetting
Thiscanbeadjustedfromonallthetime(24hr)oronataspecificluxlightinglevel
S5
S6
Light
S5
S6
Light
0
0
24hr
I
0
30lx
0
I
50lx
I
I
10lx











On
S1
S2
S3
S4
S5
S6
PositionI
Position0
Distance
Time
Light

DIPSWITCHLAYOUT








Note:SwitchonisPositionIandoffisPosition0
Distancesetting
Note:Werecommendamountingheightofbetween1.8to2.5m.Thetablebelowshowssensitivitydistanceinideal
conditions.
S1
S2
Distance
S1
S2
Distance
0
0
2m
I
0
6m
0
I
4m
I
I
8m

Timesetting
S3
S4
Time
S3
S4
Time
0
0
8sec
I
0
8min
0
I
3min
I
I
12min

Lightcontrolsetting
Thiscanbeadjustedfromonallthetime(24hr)oronataspecificluxlightinglevel
S5
S6
Light
S5
S6
Light
0
0
24hr
I
0
30lx
0
I
50lx
I
I
10lx











On
S1
S2
S3
S4
S5
S6
PositionI
Position0
Distance
Time
Light
3
Microwave
sensor
Dip switches
S1 to S6
Mains
connections

DETECTIONDIAGRAM
WARNING
Thisproductmustbedisconnectedfromthecircuitifsubjectedtoanyhighvoltageorinsulationresistancetesting.
Irreparabledamagewilloccurifthisinstructionisnotfollowed.
GENERAL
Theunitshouldberecycledinthecorrectmannerwhenitreachestheendofitslife.Checklocalauthoritiesforwhere
facilitiesexist.
Cleanwithasoftdryclothonly,donotuseaggressivecleaningproductsorsolventswhichmaydamagethesensor.
Warranty
Thisproducthasawarrantyof1yearfromdateofpurchase.Failuretoinstallthisproductinaccordancewiththecurrent
editionoftheIEEWiringRegulations,improperuse,orremovalofthebatchcodeswillinvalidatethewarranty.Ifthis
productshouldfailwithinitswarrantyperioditshouldbereturnedtotheplaceofpurchaseforafreeofcharge
replacement.MLAccessoriesdoesnotacceptresponsibilityforanyinstallationcostsassociatedwiththereplacement
product.Yourstatutoryrightsarenotaffected.MLAccessoriesreservetherighttoalterproductspecificationwithoutprior
notice.
Ceiling
2mto8m
Floor
Mountingheight
1.8m-2.5m
This product must be disconnected from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this instruction is not followed.
The unit should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the sensor.
This product has a warranty of 1 year from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of
the batch codes will invalidate the warranty. If this product should fail within its warranty period it
should be returned to the place of purchase for a free of charge replacement. ML Accessories does
not accept responsibility for any installation costs associated with the replacement product. Your
statutory rights are not affected. ML Accessories reserve the right to alter product specification
without prior notice.
WARNING
DETECTION DIAGRAM
GENERAL
WARRANTY
4

ML Accessories Limited
LU5 5TA
www.mlaccessories.co.uk SBOCT16_V2
5