ML Accessories Knightsbridge SK005A Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
SK005A

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following product:
SK005A
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this product should only be carried out by a qualified electrician or
competent person to the latest Building and current IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this product is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• This product is Class I and requires an earth
• This product is IP54 rated (only when the product is in the closed position with no
appliances attached)
• This product is for indoor use only
• Provide power to the required point of installation
• Locate a suitable place to mount the product. The mounting surface should be a
minimum of 10mm and a maximum of 50mm thickness, and there must be sufficient
space beneath the surface when the product is in the closed position
• Cut a 90mm hole in the surface allowing a 25mm clearance around the hole (see Fig 1)

• Remove the mounting collar and rubber gasket by rotating anti-clockwise
• Insert the product through the hole, place into the desired orientation, insert the rubber
gasket, and tighten the mounting collar to the underside (see Fig. 2)
Fig. 1
Fig. 2
90mm
25mm

• Connect to mains supply via the pre-wired cable and plug
Fig. 3a Fig. 3b
OPERATION
• To raise the product, gently lift the handle on the top cover. Raise until it clicks, this
means it’s locked in position (see Fig 3a)
• To lower the product press the release button (see Fig 3b)
Lift the handle and
pull product up

Fig. 4
YES
SETTING UP BLUETOOTH SPEAKER
• Always use the handle to raise/lower the product (see Fig 4)
When the fitting is switched on, the Bluetooth signal indicator will start flashing - at this
point the fitting is discoverable (see Fig 5)
NO

WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this
product in accordance with the current edition of the IEE Wiring Regulations, improper
use, or removal of the batch codes will invalidate the warranty. If this product should fail
within its warranty period it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
GENERAL
The fitting should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the fitting.

Fig. 5
WARNING
USB CHARGING FUNCTION
This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
Please note that we do not recommend our 13A sockets be used for Electric Vehicle (EV)
charging for prolonged periods.
This product is designed for charging portable USB devices only and contains a short
circuit and overload protection feature. If there is no power from the USB socket unplug
the connected device. Check to ensure the USB socket and USB device have not come into
contact with water, liquid or debris and the cable to the device is not damaged. With no
device connected to the USB socket it will automatically reset and be ready for use.
• Turn on the Bluetooth on your device and search for devices
• Locate the fitting on the Bluetooth device list (called SPEAKER) and pair
• Once the device has paired successfully an audible beep will be heard and the Bluetooth
signal indicator will flash

Manufacturers Declaration of Conformity
For ML Accessories (Knightsbridge)
Electrical products in accordance with UKCA marking
ML Accessories Ltd. declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation
UKCA marking legislation
UK SI 2016 No. 1091 Electro Magnetic Compatibility Regulations 2016
UK SI 2016 No. 1101 The Electrical Equipment (Safety) Regulations 2016
UK SI 2012 No. 3032 Restriction of the use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations 2012
UK SI 2017 No. 1206 Radio Equipment regulations 2017
UK SI 2021 No. 1095 The Ecodesign for Energy-Related Products and Energy
Information (Lighting Products) Regulations 2021
Included Legislation
UK SI 2008 No. 2852 UK REACH
UK SI 2013 No. 3113 WEEE
Safety Standards
Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The products comply with all essential requirements of
the directives.
Scott Brewer Catherine Connolly
Head of Technical CEO
ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT
This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.

Manufacturers Declaration of Conformity
For ML Accessories (Knightsbridge)
Electrical products in accordance with CE marking
ML Accessories Ltd. Declare that all products have been designed, manufactured, and tested in
accordance with the requirements of the relevant legislation
CE marking legislation
In Accordance with the following Directives:
2014/35/EU Low Voltage Directive
2014/30/EU EMC Directive
2014/53/EU Radio Equipment Directive
Including Legislation
1907/2006 REACH
2015/863 RoHS
2021/341 ERP
Safety Standards
Full individual declarations and specific safety standards applicable to relevant product series can be found on
our website www.mlaccessories.co.uk
We hereby declare that the equipment named above has been designed to comply with the relevant
sections of the above referenced specifications. The product complies with all essential requirements of
the directives.
Scott Brewer Catherine Connolly
Technical Manager CEO
ML Accessories Ltd. Unit E Chiltern Park, Boscombe Road, Dunstable. Bedfordshire, LU5 4LT
This declaration becomes invalid if technical or operational modifications are introduced without ML Accessories Ltd. written consent.

AKJUN22_V4
11
Supplied By:
(UK) Manufacturer
ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT,
www.mlaccessories.co.uk
(EU) Authorised Representative
nnuks Holding GmbH, Niederkasseler Lohweg 18,
40547 Düsseldorf, Germany,
Email: [email protected]om