ML Accessories OSPIRKW User manual

LET’S GET
YOU SET UP

Add Device
(2.4 GHz only)
To add a device tap the “+” on top right corner, select the product category
and follow the on-screen instructions
USER GUIDE
Download the
SmartKnight App
On Google Play (AndroidTM) or App Store®(Apple®).
Open the app, tap “Register” and follow the on-screen instructions
Enjoy
Enjoy your connected product. For more in-depth instructions,
please see section titled “Wi-Fi Control” in this leaflet

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following product:
OSPIRKW
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• Do not overload this accessory or subject it to conditions outside its rating
• This product is for indoor use only
• This product is Class II double insulated
• This product is IP20 rated
INSTALLATION & MAINTENANCE MANUAL
OSPIRKW

INSTALLATION
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring
not to infringe with any joists, gas/water pipes or electrical cables
• Loosen the screw on the terminal cover
• Ensuring correct polarity is observed, terminate the mains cable Live (Brown), Neutral
(Blue) and the L’ (Load Live) into the sensor (see Fig. 2)
Fig. 1
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product:
OSPIRKW
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•Do not overload this accessory or subject it to conditions outside its rating
•This product is for indoor use only
•This product is Class II double insulated
•This product is IP20 rated
INSTALLATION
•Provide power to the required point of installation
•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to
infringe with any joists, gas/water pipes or electrical cables
Fig. 1
•Loosen the screw on the terminal cover
•Ensuring correct polarity is observed, terminate the mains cable Live (Brown), Neutral (Blue) and the L’
(Load Live) into the sensor (see Fig. 2)
Fig. 2

• Fasten down the screw on the terminal cover ensuring the mains cable is secure under
the cable clamp
• Lift both spring clips on the sides of the sensor and push into the ceiling (see Fig. 3)
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product:
OSPIRKW
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•Do not overload this accessory or subject it to conditions outside its rating
•This product is for indoor use only
•This product is Class II double insulated
•This product is IP20 rated
INSTALLATION
•Provide power to the required point of installation
•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to
infringe with any joists, gas/water pipes or electrical cables
Fig. 1
•Loosen the screw on the terminal cover
•Ensuring correct polarity is observed, terminate the mains cable Live (Brown), Neutral (Blue) and the L’
(Load Live) into the sensor (see Fig. 2)
Fig. 2
•Fasten down the screw on the terminal cover ensuring the mains cable is secure under the cable
clamp
•Lift both spring clips on the sides of the sensor and push into the ceiling (see Fig. 3)
Fig. 3
•Switch on and check for correct operation
SENSOR SETTINGS
Fig. 4
Time –The time can be set to 30 sec, 1 min, 5 min, 15 min, 30 min, Test and Pulse
Pulse setting: when motion is detected and depending on the Lux setting, the sensor will turn the load on for 1
second and then off for 9 seconds until the next detection.
Test setting: the Lux setting is deactivated and when motion is detected the load will turn on for 3 seconds.
Lux –This controls the light level at which the sensor will operate when motion is detected. At the maximum
position ( ), the sensor will switch during daylight. At the lowest setting, the sensor will only operate in total
darkness.
Teach in - When this option is selected the sensor will memorise the current lux level. When the lux
level drops below this, the load will turn on. When the lux level rises above this, the load will turn off.
Sens –This controls the range of the sensor with a maximum of 4.5m when installed at 2.5m height.
• Switch on and check for correct operation
Fig. 2
Fig. 3

Time – the time can be set to 30 sec, 1 min, 5 min, 15 min, 30 min, Test and Pulse
Pulse setting: when motion is detected and depending on the Lux setting, the sensor will
turn the load on for 1 second and then off for 9 seconds until the next detection.
Test setting: the Lux setting is deactivated and when motion is detected the load will turn on
for 3 seconds.
Lux – this controls the light level at which the sensor will operate when motion is detected.
At the maximum position ( ), the sensor will operate during daylight. At the lowest setting,
the sensor will only operate in total darkness.
Lux memory – if the lux arrow is pointing towards the "lux memory" setting, the
current ambient light level will be memorised and used as the light level where the PIR
sensor will become active and start sensing for motion
Sens – This controls the range of the sensor with a maximum of 4.5m when installed at
2.5m height.
SENSOR SETUP
•Fasten down the screw on the terminal cover ensuring the mains cable is secure under the cable
clamp
•Lift both spring clips on the sides of the sensor and push into the ceiling (see Fig. 3)
Fig. 3
•Switch on and check for correct operation
SENSOR SETTINGS
Fig. 4
Time –The time can be set to 30 sec, 1 min, 5 min, 15 min, 30 min, Test and Pulse
Pulse setting: when motion is detected and depending on the Lux setting, the sensor will turn the load on for 1
second and then off for 9 seconds until the next detection.
Test setting: the Lux setting is deactivated and when motion is detected the load will turn on for 3 seconds.
Lux –This controls the light level at which the sensor will operate when motion is detected. At the maximum
position ( ), the sensor will switch during daylight. At the lowest setting, the sensor will only operate in total
darkness.
Teach in - When this option is selected the sensor will memorise the current lux level. When the lux
level drops below this, the load will turn on. When the lux level rises above this, the load will turn off.
Sens –This controls the range of the sensor with a maximum of 4.5m when installed at 2.5m height.
•Fasten down the screw on the terminal cover ensuring the mains cable is secure under the cable
clamp
•Lift both spring clips on the sides of the sensor and push into the ceiling (see Fig. 3)
Fig. 3
•Switch on and check for correct operation
SENSOR SETTINGS
Fig. 4
Time –The time can be set to 30 sec, 1 min, 5 min, 15 min, 30 min, Test and Pulse
Pulse setting: when motion is detected and depending on the Lux setting, the sensor will turn the load on for 1
second and then off for 9 seconds until the next detection.
Test setting: the Lux setting is deactivated and when motion is detected the load will turn on for 3 seconds.
Lux –This controls the light level at which the sensor will operate when motion is detected. At the maximum
position ( ), the sensor will switch during daylight. At the lowest setting, the sensor will only operate in total
darkness.
Teach in - When this option is selected the sensor will memorise the current lux level. When the lux
level drops below this, the load will turn on. When the lux level rises above this, the load will turn off.
Sens –This controls the range of the sensor with a maximum of 4.5m when installed at 2.5m height.
•Fasten down the screw on the terminal cover ensuring the mains cable is secure under the cable
clamp
•Lift both spring clips on the sides of the sensor and push into the ceiling (see Fig. 3)
Fig. 3
•Switch on and check for correct operation
SENSOR SETTINGS
Fig. 4
Time –The time can be set to 30 sec, 1 min, 5 min, 15 min, 30 min, Test and Pulse
Pulse setting: when motion is detected and depending on the Lux setting, the sensor will turn the load on for 1
second and then off for 9 seconds until the next detection.
Test setting: the Lux setting is deactivated and when motion is detected the load will turn on for 3 seconds.
Lux –This controls the light level at which the sensor will operate when motion is detected. At the maximum
position ( ), the sensor will switch during daylight. At the lowest setting, the sensor will only operate in total
darkness.
Teach in - When this option is selected the sensor will memorise the current lux level. When the lux
level drops below this, the load will turn on. When the lux level rises above this, the load will turn off.
Sens –This controls the range of the sensor with a maximum of 4.5m when installed at 2.5m height.
•Fasten down the screw on the terminal cover ensuring the mains cable is secure under the cable
clamp
•Lift both spring clips on the sides of the sensor and push into the ceiling (see Fig. 3)
Fig. 3
•Switch on and check for correct operation
SENSOR SETTINGS
Fig. 4
Time –The time can be set to 30 sec, 1 min, 5 min, 15 min, 30 min, Test and Pulse
Pulse setting: when motion is detected and depending on the Lux setting, the sensor will turn the load on for 1
second and then off for 9 seconds until the next detection.
Test setting: the Lux setting is deactivated and when motion is detected the load will turn on for 3 seconds.
Lux –This controls the light level at which the sensor will operate when motion is detected. At the maximum
position ( ), the sensor will switch during daylight. At the lowest setting, the sensor will only operate in total
darkness.
Teach in - When this option is selected the sensor will memorise the current lux level. When the lux
level drops below this, the load will turn on. When the lux level rises above this, the load will turn off.
Sens –This controls the range of the sensor with a maximum of 4.5m when installed at 2.5m height.

GENERAL
WARNING
The product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product
This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this
product in accordance with the current edition of the IEE Wiring Regulations, improper
use, or removal of the batch codes will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.

• Download the SmartKnight app on Google Play or the App Store
• Once the app is downloaded, open the app and tap “Register” then follow the on-screen
instructions
• To add a sensor to the app, ensure that the sensor is powered and tap “+” on the top right
corner
• Tap “Sensors and Security” and then tap “Motion Sensor”
• If the indicator is flashing rapidly, please skip the reset procedure and tap “Confirm the
indicator is flashing rapidly”. If the indicator is not flashing, follow the on-screen
instructions to reset it
• Connect to the desired Wi-Fi network, tap “Confirm” and the app will start searching for
devices. Please note only 2.4 GHz networks are supported and make sure your device is
connected to the same Wi-Fi network
• After the sensor has been added successfully to the app, it can be named and added to a
room. After naming it, tap “Done”
Wi-Fi CONTROL

ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
Made in China AVMAR21_V1
85