ML Accessories AC65136EM Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
AC65136EM / AC65158EM / AC651581EM
/ AC65170EM / AC65236EM / AC65258EM
/ AC652581EM / AC65270EM

These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
AC65136EM / AC65158EM / AC651581EM / AC65170EM / AC65236EM / AC65258EM /
AC652581EM / AC65270EM
GENERAL INSTRUCTIONS
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire/product when deciding the location for
installation
• This product is Class I and must be earthed
• This product is IP65 rated
SAFETY
INSTALLATION
• Provide power to the required point of installation
• Unfasten the clips on either side of the fitting (see Fig. 1) and remove the diffuser
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
AC65136EM / AC65158EM / AC651581EM / AC65170EM / AC65236EM / AC65258EM / AC652581EM /
AC65270EM
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this luminaire/product when deciding the location for
installation
•This product is Class I and must be earthed
•This product is IP65 rated
INSTALLATION
•Provide power to the required point of installation
•Unfasten the clips on either side of the fitting (see Fig. 1) and remove the diffuser
Fig. 1
•Remove the gear tray from the baseplate by pinching the clips at two locations (see Fig. 2)
Fig. 2
•Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas/water pipes
or electrical cables. Fixing centres are shown in Fig. 3
Fig. 1

• Remove the gear tray from the baseplate by pinching the clips at two locations (see Fig. 2)
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
AC65136EM / AC65158EM / AC651581EM / AC65170EM / AC65236EM / AC65258EM / AC652581EM /
AC65270EM
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this luminaire/product when deciding the location for
installation
•This product is Class I and must be earthed
•This product is IP65 rated
INSTALLATION
•Provide power to the required point of installation
•Unfasten the clips on either side of the fitting (see Fig. 1) and remove the diffuser
Fig. 1
•Remove the gear tray from the baseplate by pinching the clips at two locations (see Fig. 2)
Fig. 2
•Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas/water pipes
or electrical cables. Fixing centres are shown in Fig. 3
Fig. 2
• Mark the location of the fixing holes and drill the holes ensuring not to infringe with any gas/water pipes or
electrical cables. Fixing centres are shown in Fig. 3
Fig. 3
•Drill out one of the 20mm drilling guides and fit the compression gland provided
•Feed the mains cable into the luminaire, and tighten the compression gland ensuring a tight seal is
made
•Ensuring correct polarity is observed, carefully wire as shown in Fig. 4
Fig. 4
•Ensure the battery is connected via the plug and socket to the emergency inverter
•Replace the gear tray
•Fit an appropriate T8 fluorescent tube
•Replace the diffuser
•Switch on and check for correct operation, ensuring the green indicator LED is illuminated
•We recommend, on commissioning the installation, a minimum charge period of 24 hours before
carrying out an emergency duration test
•If the batteries have been left in a discharged state for an extended period, we recommend that one or
more charge and discharge cycles are completed which should help to restore the battery capacity
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a control gear which can be replaced by a professional.
Fig. 3
• Drill out one of the 20mm drilling guides and fit the compression gland provided
• Feed the mains cable into the luminaire, and tighten the compression gland ensuring a tight seal is made
• Ensuring correct polarity is observed, carefully wire as shown in Fig. 4

WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
Fig. 3
•Drill out one of the 20mm drilling guides and fit the compression gland provided
•Feed the mains cable into the luminaire, and tighten the compression gland ensuring a tight seal is
made
•Ensuring correct polarity is observed, carefully wire as shown in Fig. 4
Fig. 4
•Ensure the battery is connected via the plug and socket to the emergency inverter
•Replace the gear tray
•Fit an appropriate T8 fluorescent tube
•Replace the diffuser
•Switch on and check for correct operation, ensuring the green indicator LED is illuminated
•We recommend, on commissioning the installation, a minimum charge period of 24 hours before
carrying out an emergency duration test
•If the batteries have been left in a discharged state for an extended period, we recommend that one or
more charge and discharge cycles are completed which should help to restore the battery capacity
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a control gear which can be replaced by a professional.
Fig. 4
• Ensure the battery is connected via the plug and socket to the emergency inverter
• Replace the gear tray
• Fit an appropriate T8 fluorescent tube
• Replace the diffuser
• Switch on and check for correct operation, ensuring the green indicator LED is illuminated
• We recommend, on commissioning the installation, a minimum charge period of 24 hours before carrying
out an emergency duration test
• If the batteries have been left in a discharged state for an extended period, we recommend that one or more
charge and discharge cycles are completed which should help to restore the battery capacity

Fig. 3
•Drill out one of the 20mm drilling guides and fit the compression gland provided
•Feed the mains cable into the luminaire, and tighten the compression gland ensuring a tight seal is
made
•Ensuring correct polarity is observed, carefully wire as shown in Fig. 4
Fig. 4
•Ensure the battery is connected via the plug and socket to the emergency inverter
•Replace the gear tray
•Fit an appropriate T8 fluorescent tube
•Replace the diffuser
•Switch on and check for correct operation, ensuring the green indicator LED is illuminated
•We recommend, on commissioning the installation, a minimum charge period of 24 hours before
carrying out an emergency duration test
•If the batteries have been left in a discharged state for an extended period, we recommend that one or
more charge and discharge cycles are completed which should help to restore the battery capacity
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a control gear which can be replaced by a professional.
WARRANTY
This product has a warranty of 3 years (excluding battery) from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal
of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should
be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept
responsibility for any installation costs associated with the replacement product. Your statutory rights are not
affected. ML Accessories reserve the right to alter product specification without prior notice.
GENERAL
This product contains a control gear which can be replaced by a professional.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
Installing in areas where the temperature consistently drops below 0°C may shorten the battery life.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please see website for
dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
The batteries in this luminaire are Nickel Cadmium and must be disposed of correctly. Please contact the local
authorities for the disposal of this toxic waste.

TESTING FOR EMERGENCY LUMINAIRES
Recommended routine test procedure in accordance with BS5266
• Daily check – check LED charge indicator is illuminated
• Monthly functional test - simulate a mains supply failure for approx. 30 seconds by operation of key switch
or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge indicator is
illuminated
• Annual three hour duration test - simulate a mains supply failure for three hour continuous test by operation
of key switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge
indicator is illuminated
• If the luminaire fails any of the above tests, please contact a qualified electrician. See below for test record
sheet

230V 50Hz, 110V, IP65, Class 1, Non-Dim
DCAUG21_V2

DCAUG21_V2
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
52
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS