ML Accessories NH023AW Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
NH023AW / NH023B
NH025AW

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
NH023AW / NH023B / NH025AW
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated

INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please
confirm with the manufacturer of the sensors that they are compatible with LED luminaires.
• Provide power to the required point of installation
• Remove the front plate by placing a medium size flat-head screwdriver in the notch on
the side and lever off gently (see Fig. 1)
Fig. 1
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
NH023AW / NH023B / NH025AW
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•This product is for indoor use only
•This product is Class I and must be earthed
•This product is IP20 rated
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires.
•Provide power to the required point of installation
•Remove the front plate by placing a medium size flat-head screwdriver in the notch on the side and
lever off gently (see Fig. 1)
Fig. 1
•Connect the luminaire to the mains supply ensuring the correct polarity is observed: L –Live (brown),
E –Earth (green/yellow), N –Neutral (blue)
•All earth connections must be made and maintained. Use green/yellow sleeving on earth conductors
that are not insulated
•Check all electrical connections are secure with no loose strands of cable
•Fit the unit into a suitable wall box taking care not to compress, damage, or trap any cables, and
secure with the screws provided
•Clip the front plate onto the main assembly ensuring the screwdriver notch is at the side
•Switch on and check for correct operation

• Connect the luminaire to the mains supply ensuring the correct polarity is observed:
L – Live (brown), E – Earth (green/yellow), N – Neutral (blue)
• All earth connections must be made and maintained. Use green/yellow sleeving on earth
conductors that are not insulated
• Check all electrical connections are secure with no loose strands of cable
• Fit the unit into a suitable wall box taking care not to compress, damage, or trap any
cables, and secure with the screws provided
• Clip the front plate onto the main assembly ensuring the screwdriver notch is at the side
• Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.

WARRANTY
GENERAL
This product has a warranty of 1 year from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
• This product contains a light source of energy efficiency class G (NH023AW, NH025AW) to
Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095.
• This product contains a nonreplaceable LED light source and a nonreplaceable control gear
• Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
• This product is nondimmable.
• This product should be dismantled for disposal when it reaches the end of its life.
Please see website for dismantling instructions.
• This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.

AVOCT21_V2
02
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
35°C
TA