ML Accessories FLP Series Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
FLPxx

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
FLP100 / FLP100A / FLP150 / FLP150A / FLP200 / FLP200A
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not
exceed the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• This product is Class I and must be earthed
• This product is IP65 rated

FLPxxxx
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
FLP100 / FLP100A / FLP150 / FLP150A / FLP200 / FLP200A
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating
of the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this product when deciding the location for
installation
•This product is Class I and must be earthed
•This product is IP65 rated
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires.
•Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
•Round cable should be used for the mains supply. The use of flat cable will cause water ingress to
the fitting
•Using the bracket as a template, mark the location for, and drill the fixing holes ensuring not to
infringe with any gas/water pipes or electrical cables
•Remove the four screws on the access plate at the rear of the fitting to expose the terminal block
(see Fig. 1)
Fig.1
•Feed the cable through the compression gland on the rear of the access plate. A drip loop should be
left on the incoming mains cable (see Fig. 2)
Remove screws
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please
confirm with the manufacturer of the sensors that they are compatible with LED luminaires.
• Provide power to the required point of installation (refer to BS7671 for correct cabling
methods). Suitable IP rated junction boxes should be used where required
• Round cable should be used for the mains supply. The use of flat cable will cause water
ingress to the fitting
• Using the bracket as a template, mark the location for, and drill the fixing holes ensuring
not to infringe with any gas/water pipes or electrical cables
• Remove the four screws on the access plate at the rear of the fitting to expose
the terminal block (see Fig. 1)
Fig. 1

Fig. 2
•Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (brown),
E - Earth (green/yellow), N - Neutral (blue) (see Fig. 3)
Fig. 3
•Replace the access plate and screws ensuring gasket is in place then tighten the compression gland
ensuring a tight seal to maintain the IP rating
•Fix the bracket to the surface using suitable screws
•Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if it subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
This product is not suitable for installation in or near a coastal or marine environment.
GENERAL
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire should be replaced.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist
• Feed the cable through the compression gland on the rear of the access plate. A drip loop
should be left on the incoming mains cable (see Fig. 2)
• Connect the luminaire to the mains supply ensuring the correct polarity is observed:
L - Live (brown), E - Earth (green/yellow), N - Neutral (blue) (see Fig. 3)
• Replace the access plate and screws ensuring gasket is in place then tighten the
compression gland ensuring a tight seal to maintain the IP rating
• Fix the bracket to the surface using suitable screws
• Switch on and check for correct operation
Fig. 2
Fig. 2
•Connect the luminaire to the mains supply ensuring the correct polarity is observed: L - Live (brown),
E - Earth (green/yellow), N - Neutral (blue) (see Fig. 3)
Fig. 3
•Replace the access plate and screws ensuring gasket is in place then tighten the compression gland
ensuring a tight seal to maintain the IP rating
•Fix the bracket to the surface using suitable screws
•Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if it subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
This product is not suitable for installation in or near a coastal or marine environment.
GENERAL
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire should be replaced.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist
Fig. 3

GENERAL
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
This product is not suitable for installation in or near a coastal or marine environment.
• The light source of this luminaire is not replaceable; when the light source reaches its end
of life the whole luminaire should be replaced.
• Clean the external surfaces with a damp cloth using a mild solution of detergent and
warm water only, do not use aggressive cleaning products or solvents which may damage
the product.
• Do not use any source of high-pressure washers to maintain or clean this luminaire.
• This product is non-dimmable.
• This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist

ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
AKOCT21_V3
125
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
-20
~40°C
TA