ML Accessories CABBCCW Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
CABBCCW / CABBCWW / CABCCW
CABCWW / CABWCW / CABWWW

These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
CABBCCW / CABBCWW / CABCCW / CABCWW / CABWCW / CABWWW
GENERAL INSTRUCTIONS
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• When installing recessed, allow 50mm above and around the fitting for air dissipation (do not cover the fitting
with insulation)
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated
SAFETY
INSTALLATION
Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires.
• Provide power to the required point of installation
• To recess mount, cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring
not to infringe with any joists, gas / water pipes or electrical cables

WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following product(s):
CABBCCW / CABBCWW / CABCCW / CABCWW / CABWCW / CABWWW
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•When installing recessed, allow 50mm above and around the fitting for air dissipation (do not cover the
fitting with insulation)
•This product is for indoor use only
•This product is Class I and must be earthed
•This product is IP20 rated
INSTALLATION
Note - If this product is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires.
•Provide power to the required point of installation
•To recess mount, cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1)
ensuring not to infringe with any joists, gas / water pipes or electrical cables
Fig. 1
•To surface mount, fix the outer housing to a suitable solid surface ensuring not to infringe with any gas
/ water pipes or electrical cables
•Connect the luminaire to the mains supply using a suitable junction box (not included), ensuring the
correct polarity is observed: L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)
•Push the fitting securely into the cut-out or housing
•Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
Fig. 1
• To surface mount, fix the outer housing to a suitable solid surface ensuring not to infringe with any gas /
water pipes or electrical cables
• Connect the luminaire to the mains supply using a suitable junction box (not included), ensuring the correct
polarity is observed: L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)
• Push the fitting securely into the cut-out or housing
• Switch on and check for correct operation

WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
GENERAL
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire should be replaced.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is non-dimmable.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.

DCAUG21_V3
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
101
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS