ML Accessories NH0183BD Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
NH0183BD / NH0184SQ
NH018x INSTRUCTION MANUAL.indd 1NH018x INSTRUCTION MANUAL.indd 1 22/10/2021 10:33:3122/10/2021 10:33:31

These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
NH0183BD / NH0184SQ
GENERAL INSTRUCTIONS
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
•This product is for indoor use only
•This product is Class I and must be earthed
•This product series is IP20 rated
SAFETY
INSTALLATION
•Provide power to the required point of installation
• NH0183BD: using a 7mm spanner, remove the two nuts securing the baseplate to the luminaire
• NH0184SQ: remove the two screws either side of the baseplate
• Using the baseplate as a template, mark the location of the fixing holes and drill the holes ensuring not to
infringe with any gas/water pipes or electrical cables
• Fix the baseplate to a suitable solid surface using the screws provided
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 1):
L -Live (brown), E - Earth (green/yellow), N - Neutral (blue)
NH018x INSTRUCTION MANUAL.indd 2NH018x INSTRUCTION MANUAL.indd 2 22/10/2021 10:33:3222/10/2021 10:33:32

GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type, please check compatibility before installation.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
NH0183BD / NH0184SQ
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•This product is for indoor use only
•This product is Class I and must be earthed
•This product series is IP20 rated
INSTALLATION
•Provide power to the required point of installation
•NH0183BD: using a 7mm spanner, remove the two nuts securing the baseplate to the luminaire
•NH0184SQ: remove the two screws either side of the baseplate
•Using the baseplate as a template, mark the location of the fixing holes and drill the holes ensuring not
to infringe with any gas/water pipes or electrical cables
•Fix the baseplate to a suitable solid surface using the screws provided
•Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 1): L -
Live (brown), E - Earth (green/yellow), N - Neutral (blue)
Fig. 1
•Fit two suitable GU10 lamps
•Switch on and check for correct operation
GENERAL
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type, please check compatibility before installation.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
WARRANTY
Fig. 1
•Fit two suitable GU10 lamps
•Switch on and check for correct operation
NH018x INSTRUCTION MANUAL.indd 3NH018x INSTRUCTION MANUAL.indd 3 22/10/2021 10:33:3222/10/2021 10:33:32

WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
NH018x INSTRUCTION MANUAL.indd 4NH018x INSTRUCTION MANUAL.indd 4 22/10/2021 10:33:3222/10/2021 10:33:32

AKOCT21_V2
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
02
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
NH018x INSTRUCTION MANUAL.indd 5NH018x INSTRUCTION MANUAL.indd 5 22/10/2021 10:33:3222/10/2021 10:33:32