ML Accessories FLN10 Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
FLN10 / FLN20 / FLN30 / FLN50 / FLNMIC / FLNPIR

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
FLN10 / FLN20 / FLN30 / FLN50 / FLNMIC / FLNPIR
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this product is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• Do not overload this accessory or subject it to conditions outside its rating
• The FLNxx fittings are Class I and must be earthed
• This FLNMIC and FLNPIR accessories are Class II double insulated
• This product series is IP65 rated

INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
FLN10 / FLN20 / FLN30 / FLN50 / FLNMIC / FLNPIR
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this product is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
•Do not overload this accessory or subject it to conditions outside its rating
•The FLNxx fittings are Class I and must be earthed
•This FLNMIC and FLNPIR accessories are Class II double insulated
•This product series is IP65 rated
INSTALLATION
Note - Microwave sensors may not be suitable for all installations, for example enclosed spaces, as they are
able to detect movement through non-metallic surfaces like plasterboard and thin doors. Both sensors can be
falsely triggered by changes in temperature, therefore should not be installed near sources of heat such as
boiler flues.
•Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
•Round cable should be used for the mains supply, with an outer diameter of 7-9mm and a CSA of up
to 1.5mm2. The use of flat cable will cause water ingress to the fitting. A drip loop should be left on the
incoming cable
•Using the bracket as a template, mark the location for, and drill the fixing holes ensuring not to infringe
with any gas / water pipes or electrical cables. This can be done without removing the bracket from the
fitting (see Fig. 1)
Fig. 1
•Fix the luminaire to a suitable solid surface using the wall plugs and screws provided
•Tilt so that the cable entry points are accessible
•Unscrew the sealing nut from the compression gland (see Fig. 2) and fit it over the supply cable
INSTALLATION
Note - Microwave sensors may not be suitable for all installations, for example
enclosed spaces, as they are able to detect movement through non-metallic surfaces
like plasterboard and thin doors. Both sensors can be falsely triggered by changes in
temperature, therefore should not be installed near sources of heat such as boiler flues.
• Provide power to the required point of installation (refer to BS7671 for correct cabling
methods). Suitable IP rated junction boxes should be used where required
• Round cable should be used for the mains supply, with an outer diameter of 5-7.4mm
and a CSA of up to 1.5mm2. The use of flat cable will cause water ingress to the fitting. A
drip loop should be left on the incoming cable
• Using the bracket as a template, mark the location for, and drill the fixing holes ensuring
not to infringe with any gas/water pipes or electrical cables. This can be done without
removing the bracket from the fitting (see Fig. 1)
Fig. 1

• Fix the luminaire to a suitable solid surface using the wall plugs and screws provided
• Tilt so the cable entry points are accessible
• Unscrew the sealing nut from the compression gland (see Fig. 2) and fit it over the supply
cable
• Unscrew the main body of the compression gland from the fitting ensuring that the
hexagonal lock ring is not dislodged (see Fig. 2)
• Remove the protective insert from the compression gland, leaving the rubber gasket in
place (see Fig. 2), and pass the supply cable through the compression gland
• Prepare the supply cable as shown by stripping back the outer sheath and basic insulation
to the correct length (see Fig. 3)
Fig. 2
Fig. 2
•Unscrew the main body of the compression gland from the fitting, ensuring that the hexagonal lock ring
is not dislodged (see Fig. 2)
•Remove the protective insert from the compression gland, leaving the rubber gasket in place (see Fig.
2), and pass the supply cable through the compression gland
•Prepare the supply cable as shown by stripping back the outer sheath and basic insulation to the
correct length (see Fig. 3)
Fig. 3
•Connect the supply cable ensuring the correct polarity is observed: L - Live (brown), E - Earth
(green/yellow), N - Neutral (blue). Please be aware that undue pulling or rotating of the termination
block will cause damage to the fitting
•Tighten the compression gland and sealing nut ensuring a tight seal is made. Do not overtighten
•Tilt the fitting to the desired angle and tighten the nuts on the side
•Switch on and check for correct operation
PIR / Microwave Sensor Accessory
•Isolate the mains supply to the fitting
•Remove the capping nut, and using plyers pull out the protective insert from the fitting (see Fig. 4)

• Connect the supply cable ensuring the correct polarity is observed: L - Live (brown),
E - Earth (green/yellow), N - Neutral (blue). Please be aware that undue pulling or
rotating of the termination block will cause damage to the fitting
• Tighten the compression gland and sealing nut ensuring a tight seal is made. Do not
overtighten
• Tilt the fitting to the desired angle and tighten the nuts on the side
• Switch on and check for correct operation
Fig. 2
•Unscrew the main body of the compression gland from the fitting, ensuring that the hexagonal lock ring
is not dislodged (see Fig. 2)
•Remove the protective insert from the compression gland, leaving the rubber gasket in place (see Fig.
2), and pass the supply cable through the compression gland
•Prepare the supply cable as shown by stripping back the outer sheath and basic insulation to the
correct length (see Fig. 3)
Fig. 3
•Connect the supply cable ensuring the correct polarity is observed: L - Live (brown), E - Earth
(green/yellow), N - Neutral (blue). Please be aware that undue pulling or rotating of the termination
block will cause damage to the fitting
•Tighten the compression gland and sealing nut ensuring a tight seal is made. Do not overtighten
•Tilt the fitting to the desired angle and tighten the nuts on the side
•Switch on and check for correct operation
PIR / Microwave Sensor Accessory
•Isolate the mains supply to the fitting
•Remove the capping nut, and using plyers pull out the protective insert from the fitting (see Fig. 4)
Fig. 3

• Isolate the mains supply to the fitting
• Remove the capping nut, and using plyers pull out the protective insert from the fitting
(see Fig. 4)
• Align the pins on the sensor, push onto the fitting, and tighten ensuring a good seal is
made. Do not overtighten
• The rotation and tilt of both sensors can be adjusted once fitted. For the PIR accessory,
please ensure it is positioned with the adjustment dials at the bottom
• With the LUX set to Daytime, and the TIME set to the minimum, perform a walk test to
set the SENS setting so the required detection area is covered. Then set the TIME and
LUX controls to the desired settings:
PIR / MICROWAVE SENSOR ACCESSORY
Fig. 4
•Align the pins on the sensor, push onto the fitting, and tighten ensuring a good seal is made. Do not
overtighten
•The rotation and tilt of both sensors can be adjusted once fitted. For the PIR accessory, please ensure
it is positioned with the adjustment dials at the bottom
•With the LUX set to Daytime, and the TIME set to the minimum, perform a walk test to set the SENS
setting so the required detection area is covered. Then set the TIME and LUX controls to the desired
settings:
Setting
FLNMIC
FLNPIR
SENS
Minimum: up to 4m
Maximum: up to 12m
Minimum: up to 5m
Maximum: up to 10m
LUX
Minimum: 3 lux
Maximum: 2000 lux
Minimum: 10 lux
Maximum: 2000 lux
TIME
Minimum: 10 sec
Maximum: 15 min
Minimum: 10 sec
Maximum: 7 min
Override Function (FLNPIR only)
•Switch the mains supply to the fitting OFF-ON-OFF-ON within three seconds. The light flashes ON-
OFF-ON to indicate that it is in override mode. To return to automatic mode, switch the mains supply to
the fitting off for at least 10 seconds, then switch on again
•The FLNMIC has no override function
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
The LED lamps fitted in this product are non-replaceable. The product should be recycled in the correct manner
when it reaches the end of its life. Check local authorities for where facilities exist.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of
purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
Fig. 4

GENERAL
WARNING
The light source of this luminaire is not replaceable; when the light source reaches its end of
life the whole luminaire should be replaced.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm
water only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist
This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
Override Function (FLNPIR only)
• Switch the mains supply to the fitting OFF-ON-OFF-ON within three seconds. The light
flashes ON-OFF-ON to indicate that it is in override mode. To return to automatic mode,
switch the mains supply to the fitting off for at least 10 seconds, then switch on again
• The FLNMIC has no override function
Setting FLNMIC FLNPIR
SENS Minimum: up to 4m / Maximum: up to 12m Minimum: up to 5m / Maximum: up to 10m
LUX Minimum: 3 lux / Maximum: 2000 lux Minimum: 10 lux / Maximum: 2000 lux
TIME Minimum: 10 sec / Maximum: 15 min Minimum: 10 sec / Maximum: 7 min

DCAUG21_V3
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
139
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
-20
~40°C
TA