ML Accessories UNDKIT3WWW Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
UNDKIT3WWW / UNDKIT3WCW
UNDKIT3BCWW / UNDKIT3BCCW

These instructions should be read carefully and retained after installation by the
end-user for future reference and maintenance.
These instructions should be used to aid the installation of the following
products: UNDKIT3WWW / UNDKIT3WCW / UNDKIT3BCWW / UNDKIT3BCCW
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location
for installation
• This product is Class II double insulated
• This product series is IP20 rated
•Warning – a minimum of 2 lamps must be attached the driver before
energising, failure to follow this instruction will cause damage to the lamp

INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please
confirm with the manufacturer of the sensors that they are compatible with LED luminaires
Recessed installation
• Provide power to the required point of installation
• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring
not to infringe with any joists, gas/water pipes or electrical cables
• Remove the backplate and fit the lamp into the cut-out (see Fig. 2)
Fig. 1
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end-user for future reference
and maintenance.
These instructions should be used to aid the installation of the following products:
UCKIT3WWW / UCKIT3WCW / UCKIT3BCWW / UCKIT3BCCW
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•This product is Class II double insulated
•This product series is IP20 rated
•Warning –a minimum of 2 lamps must be attached the driver before energising, failure to
follow this instruction will cause damage to the lamp
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the
manufacturer of the sensors that they are compatible with LED luminaires
Recessed installation
•Provide power to the required point of installation
•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to
infringe with any joists, gas/water pipes or electrical cables
Fig. 1
•Remove the backplate and fit the lamp into the cut-out (see Fig. 2)

Fig. 2
•Connect the lamp to the 6-way hub (see Fig. 3)
Fig. 3 Note –Before adding or removing lamps from the 6-way hub, please ensure that the power to the kit is switched off. Please note that if more lamps are needed, up to a maximum of 6, a connector should be removed from the hub and replaced by a lamp. Connectors must be inserted in any unused hub terminals for the kit to work. The minimum number of lamps per driver is 2, if fewer are used this will cause irreparable damage to the lamp. •Connect the pre-wired 6-way hub to the secondary side of the driver ensuring that correct polarity is
observed: Positive –(red); Negative –(black)
•Connect the driver to the mains supply ensuring that correct polarity is observed: L –Live (brown), N –
Neutral (blue)
•Switch on and check for correct operation Surface mounting •Provide power to the required point of installation •Using the mounting bracket as a template, mark the location for, and drill the fixing holes ensuring not
to infringe with any gas/water pipes or electrical cables
•Fix the base to a suitable solid surface using the screws provided. Please ensure that the lamp cable is
routed through the slot in the backplate (see Fig. 4)
Fig. 2
•Connect the lamp to the 6-way hub (see Fig. 3)
Fig. 3
Note –Before adding or removing lamps from the 6-way hub, please ensure that the power to the kit is
switched off. Please note that if more lamps are needed, up to a maximum of 6, a connector should be removed
from the hub and replaced by a lamp. Connectors must be inserted in any unused hub terminals for the kit to
work. The minimum number of lamps per driver is 2, if fewer are used this will cause irreparable damage
to the lamp.
•Connect the pre-wired 6-way hub to the secondary side of the driver ensuring that correct polarity is
observed: Positive –(red); Negative –(black)
•Connect the driver to the mains supply ensuring that correct polarity is observed: L –Live (brown), N –
Neutral (blue)
•Switch on and check for correct operation
Surface mounting
•Provide power to the required point of installation
•Using the mounting bracket as a template, mark the location for, and drill the fixing holes ensuring not
to infringe with any gas/water pipes or electrical cables
•Fix the base to a suitable solid surface using the screws provided. Please ensure that the lamp cable is
routed through the slot in the backplate (see Fig. 4)
Fig. 2
Fig. 3
• Connect the lamp to the 6-way hub (see Fig. 3)
Note – Before adding or removing lamps from
the 6-way hub, please ensure that the power to
the kit is switched off. Please note that if more
lamps are needed, up to a maximum of 6, a
connector should be removed from the hub and
replaced by a lamp. Connectors must be inserted
in any unused hub terminals for the kit to work.
The minimum number of lamps per driver is
2, if fewer are used this will cause irreparable
damage to the lamp.

• Connect the pre-wired 6-way hub to the secondary side of the driver ensuring that correct
polarity is observed: Positive – (red); Negative – (black)
• Connect the driver to the mains supply ensuring that correct polarity is observed: L – Live
(brown), N – Neutral (blue)
• Switch on and check for correct operation
Surface Mounting
• Provide power to the required point of installation
• Using the mounting bracket as a template, mark the location for, and drill the fixing holes
ensuring not to infringe with any gas/water pipes or electrical cables
• Fix the base to a suitable solid surface using the screws provided. Please ensure that the
lamp cable is routed through the slot in the backplate (see Fig. 4)
• Connect the lamp to the 6-way hub (see Fig. 5)
Fig. 4
•Connect the lamp to the 6-way hub (see Fig. 5)
Fig. 5
Note –Before adding or removing lamps from the 6-way hub, please ensure that the power to the kit is
switched off. Please note that if more lamps are needed, up to a maximum of 6, a connector should be removed
from the hub and replaced by a lamp. Connectors must be inserted in any unused hub terminals for the kit to
work. The minimum number of lamps per driver is 2, if fewer are used this will cause irreparable damage
to the lamp.
•Connect the pre-wired 6-way hub to the secondary side of the driver ensuring that correct polarity is
observed: Positive –(red); Negative –(black)
•Connect the driver to the mains supply ensuring that correct polarity is observed: L –Live (brown), N –
Neutral (blue)
•Switch on and check for correct operation
Fig. 4

Fig. 4
•Connect the lamp to the 6-way hub (see Fig. 5)
Fig. 5 Note –Before adding or removing lamps from the 6-way hub, please ensure that the power to the kit is switched off. Please note that if more lamps are needed, up to a maximum of 6, a connector should be removed from the hub and replaced by a lamp. Connectors must be inserted in any unused hub terminals for the kit to work. The minimum number of lamps per driver is 2, if fewer are used this will cause irreparable damage to the lamp. •Connect the pre-wired 6-way hub to the secondary side of the driver ensuring that correct polarity is
observed: Positive –(red); Negative –(black)
•Connect the driver to the mains supply ensuring that correct polarity is observed: L –Live (brown), N –
Neutral (blue)
•Switch on and check for correct operation
Note – Before adding or removing lamps from the 6-way hub, please ensure the power to
the kit is switched off. Please note that if more lamps are needed, up to a maximum of 6,
a connector should be removed from the hub and replaced by a lamp. Connectors must be
inserted in any unused hub terminals for the kit to work. The minimum number of lamps
per driver is 2, if fewer are used, this will cause irreparable damage to the lamp.
• Connect the prewired 6-way hub to the secondary side of the driver ensuring
correct polarity is observed: Positive – (red); Negative – (black)
• Connect the driver to the mains supply ensuring correct polarity is observed:
L – Live (brown), N – Neutral (blue)
• Switch on and check for correct operation
Fig. 5

ADDITIONAL ACCESSORIES
WARNING
GENERAL
This luminaire must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
The kit can be expanded by adding
extra lamps, to a maximum of 6
per driver.
The LED lamps fitted in this product are non-replaceable. The product should be recycled
in the correct manner when it reaches the end of its life. Check local authorities for where
facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
This luminaire is dimmable with a trailing-edge dimmer only.
PART CODE DESCRIPTION
UNDK3WWW 3000K White
UNDK3WCW 4000K White
UNDK3BCWW 3000K Brushed Chrome
UNDK3BCCW 4000K Brushed Chrome

ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
AVJUN20_V1
ACCESSORIES LTD ACCESSORIES LTD ACCESSORIES LTD
ACCESSORIES LTD
135
WARRANTY
This product has a warranty of 3 years from the date of purchase. Failure to install this
product in accordance with the current edition of the IEE Wiring Regulations (BS7671),
improper use, or removal of the batch code will invalidate the warranty. If this product
should fail within its warranty period, it should be returned to the place of purchase for a
free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected.
ML Accessories reserve the right to alter product specification without prior notice.