ML Accessories RDSHCBR Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
RDSHCBR / RDSHC / RDSHW

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
RDSHCBR / RDSHC / RDSHW
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified
electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location
for installation
• Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with
insulation of any type). Suitable fire hoods must be used where required
•This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP65 rated (IP20 from above)

INSTALLATION
• Provide power to the required point of installation
• Cut a suitable hole in the ceiling as per the cut-out details (see Fig. 1) ensuring not to
infringe with any joists, gas / water pipes or electrical cables
• Attach the connector mounting arm by slotting into either one of the spring clips on the
fitting
• Remove the cable clamp on the terminal block then remove the terminal cover by
unscrewing the red screw on the top to access the terminal block
• Connect the luminaire to the mains supply ensuring that correct polarity is observed (see
Fig. 2): L - Live (brown), E - Earth (green/yellow), N - Neutral (blue)
Fig.1
Fig.2
Part code Cut-out size
RDSHxxx 64mm
These instructions should be read carefully and retained after installation by the end user for future
reference and maintenance.
These instructions should be used to aid installation of the following products:
RD1, RD2 & RDSH
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified
electrician
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•This product is Class I and must be earthed
•RD1 & RD2 are IP20 rated, RDSH is IP65 rated
INSTALLATION
•Provide power to the required point of installation
•Cut a suitable hole in the ceiling as per the cut-out details below ensuring that it does not
infringe with electrical cables, water/gas pipes or ceiling joists
Part code
Cut-out size
RD1
70mm
RD2
80mm
RDSH
64mm
•Attach the connector mounting arm by slotting into either one of the spring clips on the
fitting
•Unscrew the cable clamp on the terminal block then remove the terminal cover by
unscrewing the red screw on the top to access the terminal block
•Connect the pre-wired terminal block to the mains supply ensuring correct polarity is
observed
•Brown –LIVE, Blue –NEUTRAL, Green/Yellow –EARTH (see Fig. 1)
Fig. 1

• Replace the terminal cover and cable clamp
• Remove the bezel by unscrewing from the body of the luminaire then insert the lamp
through the fitting into the GU10 lamp holder
• Replace the bezel by screwing back onto the body of the luminaire
• Lift both spring clips on the sides of the fitting and push into the ceiling
• Switch on and check for correct operation
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
This luminaire is dimmable dependent on lamp type.
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.

AKAUG20_V4
101