ML Accessories AXREMC Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
AXREMC

AXREMC REMOTE CONTROL PROGRAMMER
• Insert 2 x AAA batteries (not included)
• Adjust sensor settings as required (see Fig. 1)
• The sensor remote has a maximum range of 15m
These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
AXREMC
Note: To change the settings on the optional AXSMOD microwave sensor module, the
AXREMC remote controller is required.
GENERAL INSTRUCTIONS

This product should be recycled in the
correct manner when it reaches the
end of its life. Check local authorities
for where facilities exist.
Fig. 1

BUTTON FUNCTION
Press the “ON/OFF” button, the light goes to constant on/off mode, sensor is
disabled. Press “Reset” or “Sensor motion” button to quit from this mode and the
sensor starts to work
Press “Reset” button, all parameters are same as setting of DIP switch or factory
settings.
Press “Sensor motion” button, the light quits from the constant on/off mode, and
the sensor starts to work (The latest setting stays in validity)
Press “DIM Test” button, the 1-10 V dimming works to test whether the 1-10Vdc
dimming ports are connected properly. After 2s, it returns to the latest setting
automatically.
Short press “DIM+ / DIM-“ button to transmit dimming signal. The brightness of
the lamp adjusts at 5% per unit.
(only apply for sensor with daylight harvesting function)
Long press>3s, sensor will take current light level as target lux level, to dim up/
down load automatically according to the change of ambient light level. (only
apply for sensor with daylight harvesting function)
Note: Detection area / Hold time / Stand-by period / Stand-by dim level /
Daylight sensor can be adjusted by pressing the corresponding button. The latest
setting will stay valid.
Press the “TEST 2S” button can enter the test mode anytime. At the mode, the
sensor parameters as below: Detection Area is 100%, Hold Time is 2s, Stand-by
Dim Level is 10%, Stand-by Period is 0s, daylight sensor disable. This function
only for testing. Quit the mode by pressing “RESET” or any other functions
buttons.
Scene
Options
Detection
Area
Hold time Stand-by
period
Stand-by
dim level
Daylight
Sensor
Induction
model
QS1 100% 30S 1min 10% 5Lux Hs
QS2 100% 1min 3min 10% 10Lux Hs
QS3 100% 5min 10min 10% 30Lux Hs

This product has a warranty of 5 years from date of purchase, Improper use, or removal
of the batch code will invalidate the warranty. If this product should fail within its warranty
period, it should be returned to the place of purchase for a free of charge replacement.
ML Accessories does not accept responsibility for any installation costs associated with the
replacement product. Your statutory rights are not affected. ML Accessories reserve the right
to alter product specification without prior notice.
WARRANTY
BUTTON FUNCTION
Press “HS” button to set the detection area to be high sensitive. Press “LS”
button to set the detection area to be low sensitive. The adjustment bases on the
“Detection Area” parameter you set.
Daylight Sensor
Set up daylight threshold:
5Lux/ 15Lux/ 30Lux/ 50Lux/ 100Lux/ 150Lux/ Disable
Stand-by period
Set up stand-by time: 0S/ 10S/ 1min/ 3min/ 5min/ 10min/ 30min/ +∞
Hold time
Set up hold time: 5S/ 30S/ 1min/ 3min/ 5min/ 10min/ 20min/ 30min
Stand-by dim level
Set up stand-by dim level: 10%/ 20%/ 30%/ 50%
Detection Area
Set up detection area: 25%/ 50%/ 75%/ 100%
Remote Distance
Toggle bottom can set the remote distance of remote control and sensor.

AKAPR22_V1
142
Supplied By:
(UK) Manufacturer
ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road,
Dunstable LU5 4LT, www.mlaccessories.co.uk
(EU) Authorised Representative
nnuks Holding GmbH, Niederkasseler Lohweg 18, 40547
Düsseldorf, Germany
Email: [email protected]om
** Product designed for indoor use only