ML Accessories RW6WW Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
RW6WW / RW6CW / RW6CCT

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
RW6WW / RW6CW / RW6CCT
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• If used under insulation, the insulation should be laid unbroken over the luminaire (not
packed around it). Only mineral wool style insulation may be used
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP65 rated (IP20 from above)

INSTALLATION
Note - If this product is being used in conjunction with an external PIR or sensor, please
confirm with the manufacturer of the sensors that they are compatible with LED luminaires.
•Provide power to the required point of installation
•Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring
not to infringe with any joists, gas/water pipes or electrical cables
Fig. 1
RW6 Series
These instructions should be read carefully and retained after installation by the end user for future
reference and maintenance.
These instructions should be used to aid installation of the following products:
RW6WW / RW6CW / RW6CCT
SAFETY
•Installation of this luminaire should only be carried out by a qualified electrician or
competent person to the latest Building and current IEE Wiring Regulations (BS7671)
•Please isolate mains prior to installation/maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not
exceed the rating of the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress of Protection) rating of this luminaire when deciding the
location for installation
•We recommend a 50mm spacing around and above the fitting for air dissipation
•This product is Class I and must be earthed
•This product is dimmable with most trailing edge dimmers
•This product is IP65 rated
INSTALLATION
Note: If this luminaire is being used in conjunction with external PIR or sensors, please confirm with
the manufacturer of the sensors that they are compatible with LED luminaires.
•Provide power to the required point of installation. Suitable IP rated junction boxes should
be used where required
•Cut a suitable hole in the ceiling as per the cut-out details in Fig 1 ensuring that it does not
infringe with electrical cables, water/gas pipes or ceiling joists
Fig 1
72mm

•With the aid of a cross-head screwdriver, remove the cover to access the mains terminal
block (see Fig 2)
Fig 2
•Connect the luminaire to the mains supply ensuring that correct polarity is observed
L - Live (brown) E - Earth (yellow/green) and N - Neutral (blue) (see Fig 3)
Fig 3
L
L
E
E
N
N
• With the aid of a cross-head screwdriver,
remove the cover to access the mains
terminal block (see Fig. 2)
• Connect the luminaire to the mains supply ensuring that correct polarity is observed:
L - Live (brown) E - Earth (yellow/green) and N - Neutral (blue) (see Fig. 3)
•Two cables can be inserted into the push-fit terminal block in order to achieve loop
in/loop-out wiring
Fig. 2
Fig. 3
•With the aid of a cross-head screwdriver, remove the cover to access the mains terminal
block (see Fig 2)
Fig 2
•Connect the luminaire to the mains supply ensuring that correct polarity is observed
L - Live (brown) E - Earth (yellow/green) and N - Neutral (blue) (see Fig 3)
Fig 3
L
L
E
E
N
N

•Lift both of the spring clips on the sides of the fitting and push into the ceiling
•Switch on and check for correct operation
Fig. 4
ADJUSTABLE CCT FITTING ONLY (RW6CCT)
COLOUR CHANGE
• To change the colour temperature of the fitting, switch the fitting on, off, and on again
within 2 seconds. Repeat this switching cycle until desired colour temperature has been
achieved (see Fig. 4)
•Refit the terminal cover and tighten screw ensuring that the strain relief grips the cable
securely
•To remove the bezel turn anti-clockwise
•To refit the bezel turn clockwise
•Hold back springs and insert fitting into ceiling
•Switch on power supply and check for correct operation
ADJUSTABLE CCT FITTING ONLY (RW6CCT)
COLOUR CHANGE
•To change the colour temperature of the fitting, switch the fitting on, off and on again within
2 seconds. Repeat this switching cycle until desired colour temperature has been achieved
(see Fig 4)
Fig 4
MEMORY FUNCTION
•The luminaire will always remain the same colour temperature until the above switching
cycle has been carried out
RESET FUNCTION
•To reset the fittings back to warm white, turn on the fittings and leave them on for 5
seconds

WARRANTY
This product has a warranty of 5 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.

GENERAL
WARNING
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which
may damage the product.
This product is dimmable using trailing edge dimmers, please check compatibility before
installation.
The light source of this luminaire is not replaceable; when it reaches its end of life the whole
luminaire should be replaced.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
MEMORY FUNCTION
• The luminaire will always remain the same colour temperature until the above switching
cycle has been carried out
RESET FUNCTION
• To reset the fittings back to warm white, turn on the fittings and leave them on for 5
seconds
• Switch the fittings off/on 4 times within 6 seconds
• Upon the 4th “on” switch, all luminaires will revert back to warm white

DCJUL21_V4
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
118
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS