Mobile Devices C4D-4G4EUAB V7+ User manual

C 4 D - 4 G 4 EU A B_ V 7 + - I N S T A LL A T I O N G U I D E
V 1.0
08/11/2019

Table of contents
Preface............................................................................................ 3
Warnings and notices ............................................................................... 3
1. Hardware features ................................................................................ 5
2. Hardware description ............................................................................ 6
2.1 External view .................................................................................. 6
2.2 Internal view ................................................................................... 6
2.3 OBD connector pin out ...................................................................... 7
2.4 OBD adapter wires..................................................................... 7
3. Preparing/installing the device................................................................ 8
3.1 Open the device ........................................................................ 8
3.2 Insert the SIM card .............................................................................. 10
3.3 Properly close the device....................................................................... 11
3.4 Install the OBD Dongle ................................................................... 12
4. LED sequences ................................................................................... 12
5. Support ....................................................................................... 12

Preface
The information contained in this installation guide is subject to changes in order to improve the reliability, design
or features without prior notice. Mobile Devices Ingénierie reserves the right to make changes in the content
without obligation to notify any person or organisation of such changes or improvements. Mobile Devices
Ingénierie can in no event be held liable for technical or editorial errors or omissions herein, nor for incidental,
special or consequential damages from the furnishing, performance or use of this installation guide.
Please contact our technical support for current updates and supplemental information concerning the use and
operation of this or other Mobile Devices Ingénierie products.
Warnings and notices
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
product.
Please read the installation guidelines, as well as the safety and operating instructions before operating your device.
Follow all instructions and heed all warnings in the installation guide.
There is a risk of explosion if the battery is replaced by a wrong battery type. Please discard empty battery
according to local regulations.
Hereby, Mobile Devices Ingénierie declares that the radio equipment type C4D-4G4EUAB_V7+ is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the
following internet address: http://www.mobile-devices.com/
The device could be used with a separation distance of X.Xcm to the human body. Users have to adopt a
holster/sleeve/cover without any metal components to maintain this distance.
Dispose of used batteries according to the instructions
RF Exposure Information (SAR)
For this device, the highest reported SAR value for usage near the body is X.XXX W/kg.
According to REDCA Technical Guidance on the publication with a restriction in the Official Journal of Europe of the
reference of standard EN 50566:2017, ensuring the safe a separation distance of Xmm or less is applied for
handled device and body-mounted wireless communication device used by the general public, the 5mm distance
is used for SAR testing and this device is compliance with Specific Absorption Rate (SAR) for general population/
uncontrolled exposure (Localized 10-gram SAR for head and trunk, limit : 2.0W/kg) specified in Council
Recommendation 1999/519/EC, and ICNIRP Guidelines, and RED (Directive 2014/53/EU), and had been tested in
accordance with the measurement methods and procedures specified in EN50566:2017, EN62311:2008 and
EN62209-2:2010

1. Hardware features
OBD Dongle
Performance
Processor
Cortex A5 - 500MHz
RAM
1 Gbytes
NAND Flash
2 Gbytes
Power supply
External power supply range
8-18V
External voltage
measurement
●
Li-pol battery
270mAh
Communication
Modem
4G Cat.4 module (LE910C4-EU)
Modem antenna
Internal
SIM
Micro SIM clot
WLAN
Wifi
WiFi 802.11 a/b/g/n/ac 2.4GHz,5 GHz
Bluetooth
BT 5.0 /BT 2.0
Positioning
GNSS receiver
U-blox M8 (GPS, GLONASS)
GNSS antenna
Internal
Interface & Telematics features
IMU
Accelerometer ±2/4/8/16G
Gyroscope ±125/245/500/1000/2000 dps
OBD protocols
CAN, KWP2000, VPW, PWM
CAN interface
Single CAN coprocessor
Buttons
1 reset button
Leds
2 bicolor LED
Environmental
Connectors
OBD connector
Operating temperature
-20°C/+50°C with Battery
-20°C/+60°C without battery
Dimensions
With OBD connector: 27x69x51 mm
Without OBD connector: 27x56x51 mm

2. Hardware description
2.1. External view
1 : OBD connector
2 : Reset button
3 : Power led
4 : Signal led
2.2. Internal view
5 : GNSS antenna
6 : SIM holder
7 : Internal battery*
* Please read warnings section at the beginning of the installation guide

2.3 OBD connector pin out
2.4 OBD adapter wires
This adapter is only used to connect the OBD to a computer (laptop/desktop).
Pin #
Comment
1
OEM specific
2
J1850+ (PWM/VPW)
3
OEM specific
4
Chassis ground
5
Signal ground
6
CAN High
7
K line
8
OEM specific
10
J1850- (PWM)
11
OEM specific
14
CAN low
15
L line
16
Battery voltage
Pin #
Wire color
2
Yellow
4
Black
5
Grey
6
Green
7
Blue
10
Violet
14
Orange
15
White
16
Red

3. Preparing/installing the device
Those operations may need the use of specific tools like :
-TORX pattern TX5 screwdriver for the screw.
-Small slotted screwdriver to remove the cover.
-Thin tweezers to insert/remove the SIM card.
3.1. Open the device
Remove the two screw using TX5 screwdriver
Use slotted screwdriver to pop-out the top cover on both side.
Slide the top cover heading back to remove it.

Move apart the side of the device and pull the corner of the back cover out of his spot
Pull the back cover on the rear and remove the back cover.
Device is now open

3.2. Insert the SIM card
The SIM card slot is located between the two electronic cards.
Insert the card with contact on bottom into the slot
and push it as far as it will go.
Once inserted the SIM card looks like this:

3.3. Properly close the device
First, insert the back cover beginning with corner near the power led.
Second, Move apart the side of the device and push the back cover on the spot
Third, insert the top cover beginning with the back and push on top to clip-on the top cover
Finally, place the screw.

3.4. Install the OBD Dongle
Connect the OBD Dongle on your vehicle OBD connector.
4. LED sequences
The Dongle has a two-coloured LED, green and red.
When both colours are brightened, you can see an orange light.
Green LED
Red LED
Sequence
Meaning
Sequence
Meaning
Dongle OFF
OFF
No Modem
/No GNSS
3times(50ms ON/100msOFF)
3550ms OFF
Ext. Power/Run
ON
No Modem
/Fix GNSS
2times(50ms ON/100msOFF)
3700ms OFF
Modem OK
/No GNSS
1 time (50ms ON/100ms OFF)
3850ms OFF
Modem OK
/Fix GNSS
2000ms ON
2000ms OFF
Shutdown/Hibernate
30ms ON / 1 s OFF
Idle/Sleep
30ms ON / 1 s OFF
5. Support
For all questions not related in this installation guide, please contact the support team by email at
[e-mail]