Mobile Devices C4D-4MEUAD V6 User manual

C4D-4MEUAD_V6 - INSTALLATION GUIDE
21/05/2019

Table of contents
Preface.....................................................................................................................................3
Warnings and notices ..........................................................................................................3
1. Hardware features ...........................................................................................................4
2. Hardware description......................................................................................................5
2.1. External view...............................................................................................................5
2.2. Internal view................................................................................................................5
* Please read warnings section at the beginning of the installation guide.........5
2.3 OBD connector pin out ............................................................................................6
3. Preparing/installing the device ....................................................................................7
3.1. Open the device to insert a SIM card.................................................................7
3.2. Properly close the device .......................................................................................8
3.3. Install the OBD Dongle...........................................................................................10
4. LED sequences ................................................................................................................10
5. Support ..............................................................................................................................10

Preface
The information contained in this installation guide is subject to changes in order to improve
the reliability, design or features without prior notice. Mobile Devices Ingénierie reserves the
right to make changes in the content without obligation to notify any person or organisation
of such changes or improvements. Mobile Devices Ingénierie can in no event be held liable
for technical or editorial errors or omissions herein, nor for incidental, special or consequential
damages from the furnishing, performance or use of this installation guide.
Please contact our technical support for current updates and supplemental information
concerning the use and operation of this or other Mobile Devices Ingénierie products.
Warnings and notices
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
Please read the installation guidelines, as well as the safety and operating instructions before
operating your device. Follow all instructions and heed all warnings in the installation guide.
There is a risk of explosion if the battery is replaced by a wrong battery type. Please discard
empty battery according to local regulations.
Hereby, Mobile Devices Ingénierie declares that the radio equipment type C4D-
4GMEUAB_V6 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address: http://www.mobile-devices.com/
The device could be used with a separation distance of X.Xcm to the human body. Users
have to adopt a holster/sleeve/cover without any metal components to maintain this
distance.
Dispose of used batteries according to the instructions.
RF Exposure Information (SAR)
For this device, the highest reported SAR value for usage near the body is X.XXX W/kg.
According to REDCA Technical Guidance on the publication with a restriction in the Official
Journal of Europe of the reference of standard EN 50566:2017, ensuring the safe a separation
distance of Xmm or less is applied for handled device and body-mounted wireless
communication device used by the general public, the 5mm distance is used for SAR testing
and this device is compliance with Specific Absorption Rate (SAR) for general population/
uncontrolled exposure (Localized 10-gram SAR for head and trunk, limit : 2.0W/kg) specified in
Council Recommendation 1999/519/EC, and ICNIRP Guidelines, and RED (Directive
2014/53/EU), and had been tested in accordance with the measurement methods and
procedures specified in EN50566:2017, EN62311:2008 and EN62209-2:2010

1. Hardware features
OBD Dongle
Performance
Processor
Cortex A5 - 500MHz
RAM
128 Mbytes
NAND Flash
256 Mbytes
Power supply
External power supply
range
8-18V
External voltage
measurement
●
Li-pol battery
450mA.h
Communication
Modem
4G Cat-M1data module (SARA R410M-
52B)
Modem antenna
Internal
Positioning
GNSS receiver
U-blox M8 (GPS, GLONASS, BeiDou)
GNSS antenna
Internal
Interface & Telematics
features
USB (2.0 Host)
powered (100mA on 5V minimum)
optional
3D Accelerometer
±2g, ±4g, ±6g, ±8g, ±16g
OBD protocols
CAN, KWP2000, VPW, PWM
Environmental
Connectors
OBD connector
Mini USB
Operating temperature *
-25/+60°C
Dimensions
With OBD connector: 27x60,5x49,5 mm
Without OBD connector: 27x48x49,5
mm
SIM card
slot
* Please read warnings section at the beginning of the installation guide

2. Hardware description
2.1. External view
1. ODB connector
2. microUSB
connector
3. LED
2.2. Internal view
4. Modem
antenna
5. GNSS
antenna
6. SIM holder
7. Internal
battery*
* Please read warnings section at the beginning of the installation guide
1
2
3
1
2
5
4
6
7
6

2.3 OBD connector pin out
Pin #
Comment
2
J1850+ (PWM/VPW)
4
Chassis ground
5
Signal ground
6
CAN High
7
K line
10
J1850- (PWM)
14
CAN low
15
L line
16
Battery voltage

3. Preparing/installing the device
3.1. Open the device to insert a SIM card

3.2. Properly close the device
First, check that the hole of the electronic card is correctly inserted in the plastic part.
If it’s not inserted proceed as shown below.
Second, insert the GPS antenna as shown below.
GOOD
NOT GOOD

Third, check that the micro USB port is correctly inserted on its place.
If it’s not inserted proceed as shown below.
Finally, insert the battery and place the screw.
GOOD
NOT GOOD

3.3. Install the OBD Dongle
Connect the OBD Dongle on your vehicle OBD connector.
4. LED sequences
The Dongle has a two-coloured LED, green and red.
When both colours are brightened, you can see an orange light.
Green LED
Red LED
Sequence
Meaning
Sequence
Meaning
Dongle OFF
OFF
No Modem
/No GNSS
3 times (50ms ON/100ms OFF)
3550ms OFF
Ext. Power/Run
ON
No Modem
/Fix GNSS
2 times (50ms ON/100ms OFF)
3700ms OFF
Modem OK
/No GNSS
1 time (50ms ON/100ms OFF)
3850ms OFF
Modem OK
/Fix GNSS
2000ms ON
2000ms OFF
Shutdown/Hibern
ate
30ms ON / 1 s OFF
Idle/Sleep
30ms ON / 1 s OFF
5. Support
For all questions not related in this installation guide, please contact the support team by
email at [e-mail]