Mobius M210 User manual

USER GUIDE
©2020 ETEROS TECHNOLOGIES INC. ALL RIGHTS RESERVED. | UG2006M210

CONTENTS

This User Guide is a comprehensive manual covering the operation and maintenance of the Mobius
M210 Mill processing machine as of the date of publication. ETEROS TECHNOLOGIES reserves the right
to make updates to the machine from time to time. In the event of an update, this User Guide will
remain appropriate for the safe operation and maintenance of your unit. This User Guide, as well as
any documentation supplied by component manufacturers, are to be considered the information
package associated with this device. Every operator must read and understand the User Guide. The
manual should be located within easy access for periodic review.
NOTES:
SAFETY 4
SAFETY INSTRUCTIONS
DISCLAIMER
WARNING LABELS
SERVICE & REPAIRS
GENERAL SAFETY PRECAUTIONS
5
5
6
6
7
VOLTAGE CONFIGURATION
WHAT’S IN THE BOX
GET TO KNOW YOUR MOBIUS M210 MILL
DUST COLLECTION PORT
12
13
13
13
INITIAL SETUP 11
PREFACE 8
INTENDED USE OF EQUIPMENT
OPERATING CONDITIONS
SPECIFICATIONS
9
9
10
OPERATION 14
OPERATION PREP
CONTROL PANEL OVERVIEW
GENERAL OPERATION
SET-UP & ADJUSTMENTS
15
15
16
17
GENERAL 18
CLEANING
MAINTENANCE
LIFTING & MOVING
WARRANTY
TROUBLESHOOTING
19
19
19
20
21

MOBIUS MILL M210 USER GUIDE
4
SAFETY

5
MOBIUSTRIMMER.COM
SAFETY INSTRUCTIONS
To ensure operator safety while in use, this device includes decaling, guarding, and other safety features.
Operators are encouraged to use caution and best judgment when using equipment. Equipment
should be serviced when required.
To avoid possible damage to the machine and risk of injury to the operator, consult with an Eteros
Technologies representative to answer any questions.
This document refers to the ETEROS TECHNOLOGIES product milling machine as the MOBIUS M210 Mill.
Since this machine has a rotary milling unit, special safety precautions must be observed to reduce the
risk of personal injury. Careless or improper use may cause serious or even fatal injury. Please read and
understand these precautions thoroughly before using the machine.
All operators must read and understand this User Guide and be trained in safe operation and use of
the MOBIUS M210 MILL. We recommend the owner of this equipment develop a standard operating
procedure specic to each worksite to address any local hazards or other conditions not outlined in this
User Guide. The MOBIUS M210 MILL must be inspected regularly for damage, component failure, and
wear. Results of inspection activity should be documented.
Eteros Technologies makes every effort to ensure the MOBIUS M210 MILL is compliant with all current
safety standards. It is the responsibility of the owner to ensure all municipal, provincial, state, county,
territorial, and federal codes, regulations and standards have been met in each working location.
Do not lend or rent your machine without providing the User Guide. A rst-time operator should receive
practical instruction before using the machine.
This machine is not to be used for any purpose other than those expressly stated in the User Guide,
advertising literature or other Eteros Technologies written material pertaining to the MOBIUS M210 MILL.
Operators must be in good physical condition and mental health to operate this device. Under no
circumstances should the device be operated by anyone under the inuence of any substance,
including drugs or alcohol, which might impair vision, dexterity, or judgment. Do not operate the
MOBIUS M210 MILL when fatigued. Be alert - If tired while operating the device, take a break. Fatigue
may result in loss of control. Working with any equipment can be strenuous. If you have any condition
that might be aggravated by strenuous work, check with your doctor before operating the device.
DISCLAIMER
ETEROS TECHNOLOGIES recognizes that the MOBIUS M210 MILL is a purpose-built machine for processing
cannabis by licensed producers. Please check all municipal, provincial/state, and federal laws and
regulations before using the MOBIUS M210 MILL. ETEROS TECHNOLOGIES does not promote or condone
the use of processing equipment in any way that may be deemed illegal.
ETEROS TECHNOLOGIES recognizes that our equipment can be used for processing herbs, hops, owers
and many other products. It is not the responsibility of ETEROS TECHNOLOGIES to conrm alternative
applications for our equipment.

MOBIUS MILL M210 USER GUIDE
6
WARNING LABELS
SERVICE & REPAIRS
Indicates a hazardous situation that, if not avoided, will result in serious
injury and / or death. This signal word is to be limited to the most extreme
situations; typically for machine components that, for functional
purposes, cannot be guarded.
Indicates a potentially hazardous situation that, if not avoided, could
result in serious injury and / or death. It includes hazards that are exposed
when guards are removed. It may also be used to alert against unsafe
practices.
Indicates a potentially hazardous situation that, if not avoided, may
result in minor or moderate injury. It may also be used to alert against
unsafe practices.
Repairs may only be carried out by Eteros Technologies or a designated authorized agent (service
technician).
Should the need arise, please notify:
ETEROS TECHNOLOGIES
502-130 INDUSTRIAL AVE.
CARLETON PLACE, ONTARIO, CANADA
K7C 3T2
www.ETEROS.com
Improper interfacing, improper repair, or unauthorized modication could result in void warranty claims.
CAUTION:
WARNING:
DANGER:

7
MOBIUSTRIMMER.COM
GENERAL SAFETY PRECAUTIONS
1. READ and become familiar with the entire User Guide. LEARN the equipment applications, limitations,
and possible hazards.
2. KEEP GUARDS IN PLACE and in working order including the upper product hopper.
3. DO NOT USE IN A DANGEROUS ENVIRONMENT or damp or wet locations. Never expose control
panel directly to rain or water. Keep work area well illuminated.
4. DO NOT use the device in the presence of ammable liquids or gases.
5. KEEP WORK AREA CLEAN. Cluttered areas and workspace invite accidents.
6. KEEP CHILDREN and BYSTANDERS AWAY from the device. Visitors should be kept at a safe distance
from the work area.
7. DON’T FORCE THE EQUIPMENT. It will operate optimally and safely at the rate for which it was
designed.
8. USE THE RIGHT TOOL. Don’t force the device to do a job for which it was not designed.
9. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective
hair covering to contain long hair.
10. ALWAYS OPERATE DEVICE IN A WELL-VENTILATED AREA. Dust generated from certain materials can
be a health hazard. Use a dust collection system whenever possible.
11. WEAR A FACE MASK OR DUST MASK. Milling operation may produce dust. If dust extraction is not
considered, a dust mask must be worn.
12. POWER DOWN AND DISCONNECT EQUIPMENT before servicing and when changing accessories,
such as screens, rotors, etc.
13. CHECK FOR DAMAGED PARTS PRIOR TO OPERATION. The equipment should be inspected prior to
use to ensure proper operation in performing its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may
affect its operation. Any damaged part including guards should be properly repaired or replaced.
14. ALWAYS WEAR EYE PROTECTION.
15. Hearing protection is generally not required when operating the M210. We recommend that noise
levels are monitored to ensure that all local, municipal, provincial and federal regulations and
recommendations are adhered to.

MOBIUS MILL M210 USER GUIDE
8
PREFACE

9
MOBIUSTRIMMER.COM
The M210 is designed and manufactured for the milling, grinding, blending and consistent particle size
reduction for cannabis and hemp. It should be used in a laboratory, clean room or production type
environment.
To optimize the performance of your M210 please ensure that your product is:
• Cannabis or Hemp
• Flower, leaf or trimmings
• Fully bucked or de-stemmed
• Dry to a moisture content of 8%-12%
NOTE: THIS DEVICE IS NOT TO BE OPERATED IN WET LOCATIONS.
OPERATING CONDITIONS
Location Indoor
Altitude 0 - 2000 metres above sea level
Temperature (ambient) 5•C - 25•C
Relative Humidity 25% - 75%
Voltage 115 V +/- 10%
230 V +/- 5%
Pollution Degree 2
Overvoltage Category II
*** SEE USER GUIDE FOR INPUT VOLTAGE CONFIGURATION ***
INTENDED USE

MOBIUS MILL M210 USER GUIDE
10
SPECIFICATIONS
Construction 304 Stainless Steel
Speed Adjustments 1 - 10
Number of Screens 7
Feed Motor 1/2 HP
Number of Milling Blades 6
Power Requirements
*** SEE USER GUIDE FOR INPUT
VOLTAGE CONFIGURATION ***
115V, 60Hz, 6AMPS or
230V, 50Hz, 6AMPS
Tool-less Disassembly Yes
Fits Through a 32” Door Yes
Width 28”
Length 28”
Height 52”
Weight 265lbs
Warranty 1 year
Certications CE and cLCus Certication
Accessories • Fine Screen
• Medium Screen
• Coarse Screen
• Custom Carts
• Custom Feed Hopper

11
MOBIUSTRIMMER.COM
INITIAL SETUP

MOBIUS MILL M210 USER GUIDE
12
VOLTAGE CONFIGURATION
The input voltage must be congured/veried on the KBMG DC Motor Drive – Model KBMG-212D.
This is done by setting the selectable jumpers for the appropriate voltage.
J1A AND J1B (AC LINE INPUT VOLTAGE): Be sure J1A and J1B are set to the actual AC Line input voltage
applied to the control.
See illustration below:

13
MOBIUSTRIMMER.COM
GET TO KNOW YOUR MOBIUS M210 MILL
GUARD
CASTERS
DUST
COLLECTION PORT
PRODUCT
HOPPER
DOOR LATCH
WITH SAFETY
INTERLOCK
TOTE
CONTROL
CONSOLE
WHAT’S IN THE BOX
DUST COLLECTION PORT
Your MOBIUS M210 MILL comes fully assembled, tested, and ready for operation. When unpacking the
device, please ensure the following items are included:
Your MOBIUS M210 MILL is equipped from the factory with a dust collection port. Connect a vacuum or
dust collection system to your milling machine to minimize the airborne dust generated.
NOTE: The dust collection port does not affect the machine operation or throughput.
• MOBIUS M210 MILL MACHINE
• ROTOR
• MILLING SCREEN
• PRODUCT HOPPER
• PRODUCT TOTE
STANDARD PRODUCT SCREEN
STANDARD PRODUCT ROTOR

MOBIUS MILL M210 USER GUIDE
14
OPERATION

15
MOBIUSTRIMMER.COM
OPERATION PREP
CONTROL PANEL OVERVIEW
Please take the following steps to conrm the MOBIUS M210 MILL is ready to operate:
• Ensure that your Mobius M210 MILL has been congured for the appropriate voltage (see p.12)
• Complete a thorough inspection of the equipment to ensure no damage occurred during
shipment
• Conrm the power cord is in good condition
• Ensure the rotor is properly installed with the spring-pin latch in place
• Ensure the milling screen is properly installed and located in the retention grooves
• Ensure the door is properly shut and secured
• Ensure the upper hopper is installed and in good working condition
• Ensure all guarding is properly installed and is in good working condition
• Ensure that the equipment is in a clear and tidy workspace and that all controls are accessible
and visible.
E-STOP - Emergency stop button – stops all moving
parts on the device.
START/RESET – Energizes the electrical panel and
safety circuit. Note: This button will be illuminated
when in operation.
FORWARD – Initiates rotor in a clockwise direction.
REVERSE - Initiates rotor in a counterclockwise
direction.
STOP – Stops rotor. Note: The rotor MUST be
stopped prior to toggling between forward and
reverse direction.
SPEED – Turn dial to adjust speed to desired rate.

MOBIUS MILL M210 USER GUIDE
16
GENERAL OPERATION
PRIOR TO DEVICE OPERATION, ENSURE ALL GUARDS AND THE
UPPER HOPPER ARE IN PLACE AND PROPERLY SECURED
PRESS THE E-STOP BUTTON AT ANY TIME TO STOP ALL MOVING
PARTS AND TURN OFF THE MACHINE
MACHINE START UP SEQUENCE
TOGGLING ROTATOR DIRECTION
1. Ensure the rotor and screen are properly installed.
2. Ensure the access door is properly closed and latched.
3. Ensure e-stop is disengaged.
4. Press the start/reset button to turn on the machine. When active, the start/reset button will be
illuminated.
5. Press the forward or reverse button to engage the rotor.
6. Turn speed dial to desired speed.
While the machine is in operation:
1. Press the stop button to stop rotor motion. Note: The rotor must be stopped prior to toggling
direction.
2. Press the forward or reverse button to engage the rotor in the desired direction.

17
MOBIUSTRIMMER.COM
ENSURE THE MOBIUS M210 MILL IS LOCKED OUT BEFORE
PREFORMING ANY SETUP, MAINTENANCE, OR CLEANING TASKS
MACHINE STOP SEQUENCE
MACHINE SHUTDOWN SEQUENCE
When the machine is in operation, press the stop button.
1. Press the stop button to stop rotor motion.
2. Press the e-stop button to de-energize the machine.
SET-UP & ADJUSTMENTS
The Mobius M210 Mill typically requires no set-up or adjustment under normal operating conditions.
The particle size and nal product consistency is dictated by the milling screen. Eteros Technologies
has several screens available for milling and blending. Please consult with our team to determine the
screen combination that best suits your needs.

MOBIUS MILL M210 USER GUIDE
18
GENERAL

19
MOBIUSTRIMMER.COM
CLEANING
MAINTENANCE
LIFTING & MOVING
With the exception of the motor, gearbox, and electrical enclosure, the MOBIUS M210 MILL can be
washed, cleaned, and wiped down with normal detergents, degreasers, and disinfectants.
The access door, rotor, and screen can be removed to facilitate cleaning. The inside of the MOBIUS
M210 MILL can be washed and wiped as needed.
The door gasket can also be removed easily for cleaning. This gasket is pressed by hand into the
groove around the circumference of the door.
The exterior of the MOBIUS M210 MILL should never be hosed or sprayed. Evidence of water near the
motor, conduit, electrical panel, or gearbox could void the machine warranty.
The MOBIUS M210 MILL is largely maintenance-free.
The door gasket is the only wear component within the Mobius Mill. The condition of the door gasket
should be inspected prior to each use. A faulty or worn door gasket will not affect the operation of the
machine, however it is necessary for dust mitigation.
The M210 gearbox is a fully sealed unit and is 100% Maintenance free for life.
This User Guide does not include instructions for machine repair. For your safety, repairs must be
completed by ETEROS TECHNOLOGIES or an authorized agent (service technician).
Should repairs be required, please contact:
ETEROS TECHNOLOGIES
502-130 INDUSTRIAL AVE.
CARLETON PLACE, ONTARIO, CANADA
K7C 3T2
www.eteros.com
Improper interfacing, improper repair, or unauthorized modication could result in void warranty claims.
The machine is easily moved and rolled on level surfaces. The machine includes four locking swivel
casters that are installed at the factory. The machine is designed to be operated on smooth and level
oors.
If lifting is required, the M210 must be lifted using a forklift on the lower structural frame between the
casters. Ensure that the forks are fully spread to avoid overturning or ipping off the forks.

MOBIUS MILL M210 USER GUIDE
20
WARRANTY
For a period of one (1) year after equipment shipment, ETEROS TECHNOLOGIES (“Seller”) warrants the
MOBIUS M210 MILL shall be free from defects in material and workmanship.
In the event of an issue covered under warranty, the original owner/purchaser of the of the MOBIUS
M210 MILL must contact ETEROS TECHNOLOGIES to le a claim. Prolonged operation of a damaged
machine may cause additional damage and/or wear not covered by warranty.
ETEROS TECHNOLOGIES
502-130 INDUSTRIAL AVE.
CARLETON PLACE, ONTARIO, CANADA
K7C 3T2
www.eteros.com
The seller understands the cost of downtime and will make every reasonable effort to process approved
warranty claims and repairs as quickly as possible. In some instances, the owner/purchaser may need
to ship the equipment to the Seller’s manufacturing facility to complete the repairs. The repairs will
come at no cost to the owner.
Rotor damage is very rare on a MOBIUS M210 MILL and is typically the result of rocks, hard metallic
objects, or poor setup. Rotor damage resulting from hard objects entering the milling chamber is
not covered under warranty. In the event of rotor damage, please contact ETEROS TECHNOLOGIES
for assessment. Repair and part replacements must be completed by ETEROS TECHNOLOGIES or an
authorized agent. To avoid rotor damage, please take care to properly maintain the MOBIUS M210
MILL and do not let hard objects enter the milling chamber.