Modus Furniture NEVIS NV23L3 User manual

A
B
A.
B.
HEADBOARD
FOOTBOARD
1 PC
1 PC
C.
D.
E.
SIDE RAIL
BED SLAT
SUPPORT LEG
BED HARDWARE BOX*
2 PCS
3 PCS
3 PCS
STEP 1 :
BOX #1 BOX #2
ASSEMBLY INSTRUCTIONS
NEVIS PANEL LOW PROFILE ASSEMBLED
UPDATED : JUNE 15TH, 2020
BED HARDWARE PACKED IN BOX #2
1
4
2 3
PHILLIPS HEAD
BOLT(8x20mm)
(6x40mm)
ALLEN BOLT
WOOD SCREW
(8x30mm)
ALLEN KEY
8
4
7 1
PCS
PCS
PCS PC
5SPRING WASHER 8
PCS
TOOL REQUIRED : PHILLIPS HEAD
SCREWDRIVER (NOT PROVIDED)
0:30
YOUR BOX
MAY CONTAIN
EXTRA HARDWARE
6
(M8)
FLAT WASHER 8
PCS
(M8)
NEVIS PANEL LOW PROFILE TWIN/FULL/QUEEN BED
C
C
E
D
C
A
5
16
5
16
C
A

3
4
D
E
STEP 2 : STEP 3 :
STEP 4 :
A
B
C
C
STEP 5 :
IF USING BED FRAME WITH ADJUSTABLE MATTRESS BASE, SKIP TO APPENDIX A: ADJUSTABLE
MATTRESS BASE ASSEMBLY SUPPLEMENT.
IF USING BED FRAME WITH STANDARD BOX SPRING OR FOUNDATION CONTINUE TO STEP 4.
STOP
C
2
D
D
E
C
A
C
ED
B
YOUR BED.
LIFT YOUR BED WHEN MOVING IT.
DRAGGING CAN DAMAGE
THE SUPPORT LEG.
READJUST LEVELERS AFTER MOVING
REMOVE BOX SPRING AND MATTRESS
BEFORE MOVING YOUR BED.
INSTRUCTIONS FOR ADJUSTING
LEVELERS :
MAINTENANCE INSTRUCTIONS :
UPDATED : JUNE 15TH, 2020
POSITION THE BED IN YOUR ROOM.
LOCATE LEVELERS UNDER EACH
SUPPORT LEG (E).
TURN LEVELERS COUNTER-CLOCKWISE
TO EXTEND, CLOCKWISE TO RETRACT.
ADJUST LEVELERS UNTIL EACH SUPPORT
LEG IS APPLYING EQUAL UPWARD
PRESSURE ON THE BED SUPPORT SLAT.
A
B
C
B
51
6
C
51
6

APPENDIX A:ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT
USE ALLEN KEY (3) TO UNSCREW ALLEN BOLTS
AND REMOVE PRE-ASSEMBLED SIDE RAIL CLEATS.
STEP 1 :
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
IF USING THIS BED FRAME WITH A STANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
AN ADJUSTABLE MATTRESS BASE IS A FREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THE BED FRAME.
PRE-ASSEMBLED SIDE RAIL CLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOW THESE INSTRUCTIONS TO REMOVE THEM.
2. WOOD SCREW (8x30mm) 7 PCS
4. ALLEN BOLT (6x40mm) 4 PCS
D. BED SLAT 3 PCS
E. SUPPORT LEG 3 PCS
NOTE: YOU MAY WISH TO RETAIN UNUSED PARTS IF IN THE FUTURE YOU INTEND TO USE THE BED FRAME WITH
A STANDARD BOX SPRING OR FOUNDATION.
3
NEVIS PANEL LOW PROFILE TWIN/FULL/QUEEN BED
UPDATED : JUNE 15TH, 2020

A
B
A.
B.
HEADBOARD
FOOTBOARD
1 PC
1 PC
C.
D.
E.
SIDE RAIL
BED SLAT
SUPPORT LEG
BED HARDWARE BOX*
2 PCS
3 PCS
6 PCS
STEP 1 :
BOX #1 BOX #2
NEVIS PANEL LOW PROFILE KING BED
ASSEMBLY INSTRUCTIONS
NEVIS PANEL LOW PROFILE ASSEMBLED
C
C
D
E
BED HARDWARE PACKED IN BOX #2
1
4
2 3
PHILLIPS HEAD
BOLT(8x20mm)
(6x40mm)
ALLEN BOLT
WOOD SCREW
(8x30mm)
ALLEN KEY
8
7
7 1
PCS
PCS
PCS PC
5SPRING WASHER 8
PCS
TOOL REQUIRED : PHILLIPS HEAD
SCREWDRIVER (NOT PROVIDED)
0:30
YOUR BOX
MAY CONTAIN
EXTRA HARDWARE
6
(M8)
FLAT WASHER 8
PCS
(M8)
C
A
5
16
5
16
C
A
UPDATED : JUNE 15TH, 2020

3
4
D
E
STEP 2 : STEP 3 :
STEP 4 : STEP 5 :
IF USING BED FRAME WITH ADJUSTABLE MATTRESS BASE, SKIP TO APPENDIX A: ADJUSTABLE
MATTRESS BASE ASSEMBLY SUPPLEMENT.
IF USING BED FRAME WITH STANDARD BOX SPRING OR FOUNDATION CONTINUE TO STEP 4.
STOP
YOUR BED.
LIFT YOUR BED WHEN MOVING IT.
DRAGGING CAN DAMAGE
THE SUPPORT LEG.
READJUST LEVELERS AFTER MOVING
REMOVE BOX SPRING AND MATTRESS
BEFORE MOVING YOUR BED.
POSITION THE BED IN YOUR ROOM.
LOCATE LEVELERS UNDER EACH
SUPPORT LEG (E).
TURN LEVELERS COUNTER-CLOCKWISE
TO EXTEND, CLOCKWISE TO RETRACT.
ADJUST LEVELERS UNTIL EACH SUPPORT
LEG IS APPLYING EQUAL UPWARD
PRESSURE ON THE BED SUPPORT SLAT.
INSTRUCTIONS FOR ADJUSTING
LEVELERS :
MAINTENANCE INSTRUCTIONS :
D
E
A
B
C
D
E
C
C
2
D
UPDATED : JUNE 15TH, 2020
A
B
C
A
B
C
C
B
51
6
C
51
6

APPENDIX A:ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT
USE ALLEN KEY (3) TO UNSCREW ALLEN BOLTS
AND REMOVE PRE-ASSEMBLED SIDE RAIL CLEATS.
STEP 1 :
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
IF USING THIS BED FRAME WITH A STANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
AN ADJUSTABLE MATTRESS BASE IS A FREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THE BED FRAME.
PRE-ASSEMBLED SIDE RAIL CLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOW THESE INSTRUCTIONS TO REMOVE THEM.
2. WOOD SCREW (8x30mm) 7 PCS
4. ALLEN BOLT (6x40mm) 7 PCS
D. BED SLAT 3 PCS
E. SUPPORT LEG 6 PCS
NOTE: YOU MAY WISH TO RETAIN UNUSED PARTS IF IN THE FUTURE YOU INTEND TO USE THE BED FRAME WITH
A STANDARD BOX SPRING OR FOUNDATION.
3
NEVIS PANEL LOW PROFILE KING BED
UPDATED : JUNE 15TH, 2020