Modus Furniture C.KING User manual

A. 1 PC
D
BOX#1
BOX#2
HARDWARE PACKED IN BOX#1
HARDWARE PACKED IN BOX#2
ALLEN BOLT(5/16"x1") 8 PCS
ALLEN BOLT(5/16"x2-1/2") 4 PCS
FLAT WASHER(5/16")12 PCS
LOCK WASHER(5/16")12 PCS
ALLEN KEY 5/16")(1 PC
1
2
3
4
5
ASSEMBLY INSTRUCTIONS
C.KING/E.KING
E
F
G
H
I
C.
D. FOOTBOARD 1 PC
E. SLAT 39 PCS
F. CENTER SLAT SUPPORT
G. SIDE RAIL SLAT CLIP 26 PCS
H. CENTER SUPPORT SLAT CLIP 26 PCS
I. SLAT SUPPORT LEG 4 PCS
1 PC
2 PCS
HARDWARE SET
B. 1 PC
A
2
3
4
FLAT WASHER(5/16")8 PCS
LOCK WASHER(5/16")8 PCS
ALLEN KEY( /1 4") 1 PC
1ALLEN BOLT(1/4"x1") 8 PCS
00:30
x2
HEADBOARD PANEL
RIGHT SIDE RAIL
LEFT SIDE RAIL
B C
ONE UPHOLSTERED BED
ONE UPHOLSTERED BED ASSEMBLED

STEP 2
STEP 1
A
C
B
A
C
D
B
2
F
I I
4
3
5
F
I
F
I I
UPDATED:JULY 23RD, 2022
STOP
IF USING BED FRAME WITH STANDARD BOX SPRING OR FOUNDATION, CONTINUE TO STEP 3.
IF USING BED WITH AN ADJUSTABLE MATTRESS BASE, SKIP STEPS 3, 4, 5&6 AND
REFERENCE APPENDIX A: ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT.
ASSEMBLY INSTRUCTIONS
C.KING/E.KING
D
B/C
D
5
5D B/C
A
B/C
A
5
5A B/C
ONE UPHOLSTERED BED
STEP 3 NOTE: USE HARDWARE PACKED IN BOX #2 FOR STEPS 3 & 4.

STEP 4
A
C
D
B
1
F
A/D
345
A
C
D
B
B/C
G
G
B/C
G
E
H
F
E
H
F
E
H
F
A
C
D
B
UPDATED:JULY 23RD, 2022
ASSEMBLY INSTRUCTIONS
C.KING/E.KING
STEP 6
ONE UPHOLSTERED BED
STEP 5: STARTING FROM HEADBOARD

INSTRUCTIONS FOR ADJUSTING LEVELERS:
MAINTENANCE INSTRUCTIONS:
ASSEMBLY COMPLETE.
POSITION THE BED IN YOUR ROOM.
LOCATE LEVELERS UNDER EACH
TURN COUNTER-CLOCKWISE TO
EXTEND, CLOCKWISE TO RETRACT.
ADJUST LEVELERS UNTIL EACH LEG
REMOVE BOX SPRING AND MATTRESS
BEFORE MOVING YOUR BED.
LIFT YOUR BED WHEN MOVING IT.
DRAGGING CAN DAMAGE
CENTER SUPPORT.
READJUST LEVELERS AFTER MOVING
YOUR BED.
SUPPORT LEG ( I ).
SUPPORT IS APPLYING EQUAL UPWARD
PRESSURE ON THE CENTER SLAT.
UPDATED:JULY 23RD, 2022
ASSEMBLY INSTRUCTIONS
C.KING/E.KING
ONE UPHOLSTERED BED

APPENDIX A:ADJUSTABLE MATTRESS BASE ASSEMBLY SUPPLEMENT
IF USING THIS BED FRAME WITH A STANDARD BOX SPRING OR FOUNDATION THESE INSTRUCTIONS DO NOT APPLY.
AN ADJUSTABLE MATTRESS BASE IS A FREESTANDING MATTRESS SUPPORT THAT SITS WITHIN
THE PERIMETER OF THE BED FRAME.
PRE-ASSEMBLED SIDE RAIL CLEATS OBSTRUCT ADJUSTABLE BASE INSTALLATION AND OPERATION.
FOLLOW THESE INSTRUCTIONS TO REMOVE THEM.
THE FOLLOWING PARTS ARE NOT REQUIRED FOR ADJUSTABLE MATTRESS BASE INSTALLATION:
USE A PHILLIPS HEAD SCREWDRIVER (NOT PROVIDED)
TO UNSCREW THE PHILLIPS SCREWS AND REMOVE THE
PRE-ASSEMBLED SIDE RAIL CLEATS.
STEP 1 :
F. CENTER SLAT SUPPORT 2 PCS
E. SLAT 39 PCS
G. SIDE RAIL SLAT CLIP 26 PCS
H. CENTER SUPPORT SLAT CLIP 26 PCS
I. 4 PCSSLAT SUPPORT LEG
ASSEMBLY INSTRUCTIONS
C.KING/E.KING
UPDATED:JULY 23RD, 2022
WARNING!
SIDE RAIL CLEATS ARE HELD IN PLACE USING PHILLIPS HEAD SCREWS. ONCE THEY ARE REMOVED THE USER
WILL NOT BE ABLE TO SAFELY RE-INSTALL THE SIDE RAIL CLEATS FOR FUTURE USE WITH A STANDARD BOX
SPRING OR FOUNDATION.
ONE UPHOLSTERED BED