modway EEI -1324 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 7
EEI -1324 DESK
Hardware:
Thank you for purchasing the MODWAY DESK！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
a Cam Post x22 b Cam x22
c Screw M4x35mm x4 d Dowel x20
f Drawer Guides x1 set
e Screw M4x14mm x8
g Bolt M6x30mm x8 h Bolt M6x35mm x8
Allen Wrench x1
j Bolt M6x65mm x4 k
m Leveler x4

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 7
EEI -1324 DESK
Component:
A Top Panel x1 B Side Panel x2
C Side Divide Panel x2 D Center Divide Panel x2
E Bottom Panel x1 F1 Drawer Front x1
F2 Left Drawer Side x1 F3 Right Drawer Side x1
F4 Drawer Back x1 F5 Drawer Bottom x1
G Leg x2 H Top Rail x1
J Bottom Rail x1
A
B
B
C
C
D
E
F1
F5
F4
F2
F3
G
G
H J

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 7
EEI -1324 DESK
HOW TO USE CAN AND CAM POST HARDWARE
STEP 1:
1. 2.
3. 4.
Note cam arrow
direction
Note cam arrow
direction
Turn cam clockwise
1/2 turn
5.
Hardware & Tools required
ax2 bx2 cx4 Phillips Head Screwdriver
( not included)
Place 1pc Side Drawer Front (F1),1pc Side Drawer Back (F4),1pc Left Drawer Side (F3), 1pc Right Drawer Side (F4)
and 1pc Side Drawer Bottom (F5) together as shown.
Attach them by 2pcs Cam Post (a), 2pcs Cam (b), 4pcs Screw (c), tighten the Screws (c) and Cam (b)
Fully tighten Cams (b), Screws (c) with Phillips Head Screw Driver (not included).
F5
F1
F4
F2
F3
c
c
b
b
a
a

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 7
EEI -1324 DESK
STEP 2:
STEP 3:
Insert 11pcs Cam Post (a) into the corresponding holes on the bottom of Top Panels (A) as shown.
Use Phillips Head Screwdriver (not included) to tighten the Cam Posts (a) clockwise until secure.
Insert 8pcs Dowel (d) into the corresponding holes on the bottom Top Panels (A) as shown.
ax20 dx20 Phillips Head Screwdriver
( not included) Hardware & Tools required
c
Insert 11pcs Cam Post (a) into the corresponding holes on the bottom of Top Panels (A) as shown.
Use Phillips Head Screwdriver (not included) to tighten the Cam Posts (a) clockwise until secure.
Insert 8pcs Dowel (d) into the corresponding holes on the bottom Top Panels (A) as shown.
Repeat the same steps and hardware for the Bottom Panel (E).
A
E
Hardware & Tools required
bx10 Phillips Head Screwdriver
( not included)

Customer Service 908-368-1025︱www.modwayfurniture.com Page 5 of 7
EEI -1324 DESK
bx10 Phillips Head Screwdriver
( not included)
STEP 4:
STEP 5:
Please put the Top Panel (A)) upside down on a carpeted or padded surface.
Place the Left Side Panels (B) and Right Side Panel (C) to the Top Panel (A) as shown.
Attach them by using 8pcs Cam (b).
Use Phillips Head Screwdriver (not included) to tighten the Cams (b) clockwise until secure.
Place the Bottom Panel (E) to the Assembled Side Panels (B), Side Divide Panel (C) and Center Divide Panel (D) as shown.
Attach them by using 10pcs Cam (b).
Hardware & Tools required
Hardware & Tools required
ex4 fx1 Phillips Head Screwdriver
( not included)
e A
Hardware & Tools required
B B
C
C
E
e
f f
D
A
D C
C
b b b
b
b
b
b
B B

Customer Service 908-368-1025︱www.modwayfurniture.com Page 6 of 7
EEI -1324 DESK
STEP 6:
STEP 7:
Attach the Top Rail (H) and Bottom Rail (J) to 1pc Leg (G) by using 4pcs Bolt (h) as shown.
Use Allen Wrench (n) to tighten all the Bolts (h) clockwise until secure.
Repeat the same steps for the remaining other Leg (G).
Place the assembled Legs (G) to the assembled Bottom Panel (E) as shown.
Connect them by using 4pcs Bolt (j).
Use Allen Wrench (n) to tighten all the Bolts (j) clockwise until secure.
Secure the 4pcs Leveler (m) to the bottom of Legs (G) as shown.
Hardware & Tools required
Hardware & Tools required
hx8 nx1
jx4 mx4 nx1
m
E
G
G
m
m
m
j
j
n j
j
G
G
H
J
h
n
h
n
h
h

Customer Service 908-368-1025︱www.modwayfurniture.com Page 7 of 7
EEI -1324 DESK
STEP 8:
STEP 9:
Place the assembled drawer to the assembled desk as shown.
Attach them by using 4pcs Screw (e).
Use Phillips Head Screwdriver (not include) to tighten the Screws (e) clockwise until secure.
Rotate the adjustable feet on bottom of each leg to desired height and leveling according to your floor surface.
Hardware & Tools required
Assembly is completed. The desk is ready to enjoy now!
Place the desk to where you desired.
ex4 Phillips Head Screwdriver
( not included)
e
e
e
e
F1