modway EEI-2788 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 6
EEI –2788 DESK
Thank you for purchasing the MODWAY DESK！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
A Cam x11
B
D
Component:
1 Top Panel x1 2 Left Panel x1
Cam Post x11
3
6
F
H Adjustable Leveler x4
K
Plastic Cover x1
Short Screw M4x14mm x12
Phillips Head Screwdriver
( Not included)
3 Right Panel x1 4 Back Panel x1
5 Divider Panel x2 6 Left Frame x1 7 Right Frame x1 8 Rail x1
C Bolt M6x40mm x2
E Dowel x2
Large Screw M7x70mm x4
G
Medium Screw M7x50mm x8
J
Allen Wrench M4 x1
1
2 3
4
5 5
7
8

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 6
EEI –2788 DESK
HOW TO USE CAM AND CAM POST HARDWARE
STEP 1:
1. 2.
3. 4.
Note cam arrow
direction
Note cam arrow
direction
Turn cam clockwise
1/2 turn
5.
Put Left Panel (2) and Right Panel (3) upside down on a carpeted or padded surface.
Insert 8 pieces of Cam Post (B) into the pre-drilled holes on Left Panel (2) and Right Panel (3) as shown.
Use Phillips Head Screwdriver (Not provided) to tighten Cam Post (B) clockwise until secure.
Bx8 Phillips Head Screwdriver
( not included) Hardware & Tools required
2 3
B
B
B
B
B
B
B
B
B
A
ABA
A

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 6
EEI –2788 DESK
STEP 2:
STEP 3:
Hardware & Tools required
Bx3 Ex2 Phillips Head Screwdriver
( not included)
4
Ax11 Phillips Head Screwdriver
( not included)
Put Back Panel (4) backside down on a carpeted or padded surface.
Insert 3 pieces of Cam Post (B) and 2 pieces of Dowel (E) into the pre-drilled holes on Left Panel (2) and Right Panel (3) as shown.
Use Phillips Head Screw Driver (Not provided) to tighten Cam Post (B) clockwise until secure.
4
B
E
B
E
B
Put Top Panel (1) to Back Panel (4) as shown.
Then Put Left Panel (2) and Right Panel (3) to the assembled Top Panel (1) and Back Panel (4) as shown.
Attach them by using 11 pieces of Cam (A).
Use Phillips Head Screwdriver (Not provided) to tighten Cams (A) clockwise until secure.
1
3
2
A A
A A
A
A
A
A
A
A
A

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 6
EEI –2788 DESK
STEP 4:
STEP 5:
Hardware & Tools required
Hardware & Tools required
Cx2 Kx1
Put Desk Top (1), left Panel (2), Right Panel (3), and Back Panel (4) upside down on a carpeted or padded surface.
Put the assembled Left Frame (6), Right Frame (7), and Rail (7) to the assembled Desk Top (1), Left Panel (2),
Right Panel (3), and Back Panel (4) as shown.
Attach them by using 4 pieces of Large Screw (D) and 8 pieces of Short Screw (G) .
Use Allen Wrench (K) to tighten Large Screw (D) clockwise until secure.
Put Left Frame (6), Right Frame (7), and Rail (8) on a carpeted or padded surface.
Insert 2 pieces of Bolt (C) into the pre-drilled holes on the end of Rail (2) through the pre-drilled holes on Left Frame (6)
and Right Frame (7).
Use Allen Wrench (K) to tighten Bolt (C) clockwise until secure.
6
4
C
C
7
1
Dx4 Phillips Head Screwdriver
( not included)
Gx8 Kx1
7
8
K
2
3
6
8
D D
G
G
G
G
D D
K

Customer Service 908-368-1025︱www.modwayfurniture.com Page 5 of 6
EEI –2788 DESK
STEP 6:
STEP 7:
Hardware & Tools required
Hardware & Tools required
Hx4
Fx8 Phillips Head Screwdriver
( not included)
Gx4 Jx1
1
Insert 4 pieces of Adjustable Leveler (H) into the bottom of Left Frame (6) and Right Frame (7) as shown.
Secure Leveler (H) by hand.
1
4
3
2
6
7
8
2
2
4
2
3
1
4
6
7
5 5
F
F
F
F
F
Carefully turn over the assembled desk.
Place 2 pieces of Divider Panel (5) to the assembled Desk Top (1) and Back Panel (4) as shown.
Insert 4 pieces of Medium Screw (F) into Divider Panel (5) from the back of assembled desk.
Insert 4 pieces of Medium Screw (F) into Divider Panel (5) from the bottom of Desk Top (1).
Insert 4 pieces of Short Screw (G) into Back Panel (4) from the back of assembled desk.
Use Phillips Head Screwdriver (not included) to tighten all Screws (F&G) until secure.
Put Plastic Cover (J) into Desk Top (1) as shown.
F
F
F
G
G
G
G
J
HH
H
H

Customer Service 908-368-1025︱www.modwayfurniture.com Page 6 of 6
EEI –2788 DESK
STEP 8:
Place the assembled desk to the position you desired.
If leveling is needed, turn Levelers (H) clockwise to down and counterclockwise to raise.
Assembly is complete. Your desk is ready to be used now!