modway EEI-2678 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 6
EEI-2678/2679 TV STAND
Hardware:
Components:
A Double-ended Bolt M8x190mm x12
B
1 Top Panel x1
Thank you for purchasing the MODWAY TV STAND！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the TV stand, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
2 Side Panel x6
D
3 Bottom Panel x2
E
F
G
H
J
C
Dowel ɸ8x40mm x24
Nut M8 x12
Flat Washer M8 x24
Box Wrench #8 x1
Short Bolt M6x25mm x4
Mat 40x40mm x4
Allen Wrench #5 x1
Long Bolt M8x30mm x8
1
2
2
2
3
3
4
2
2
2
5
5
5
5
4 Center Panel x1 5 Leg x4

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 6
EEI-2678/2679 TV STAND
STEP 1:
Ax6 Hardware & Tool required
STEP 2:
1
Put Top Panel (1) upside down on a carpeted or padded area.
Insert 6 pieces of Double-ended Bolt (A) into the corresponding holes in the Top Panel (1) by hand as shown.
Tighten all the Double-ended Bolts (A) clockwise until secure.
Bx24 Hardware & Tool required
Insert 4 pieces of Dowel (B) into 4 holes of Side Panel (2) as shown.
Repeat the same steps for the remaining 5 pieces of Side Panel (2).
Position 3 pieces of assembled Side Panel (2) to Top Panel (1) as shown.
Please confirm the assembled Double-ended Bolts (A) and Dowel (B) have been inserted into the pre-drilled holes
in Top Panel (1) fully as shown.
2
2
1
2
2
B
B
B
B
A
A
B
B
A
A
A
A
A
A

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 6
EEI-2678/2679 TV STAND
STEP 3:
Cx6 Dx6 Ex1 Hardware & Tool required
STEP 4:
1
Put Bottom Panels (3) upside down on a carpeted or padded area.
Position 1 piece of Bottom Panel (3) to the assembled Top panel (1) and Side Panels (2) as shown.
Please confirm the assembled Double-ended Bolts (A) and Dowels (B) have been inserted into the pre-drilled holes on
Bottom Panel (3) fully.
Insert 6 pieces of Nut (C) with 6 pieces of Flat Washer (D) into the assembled Double-ended Bolts (A) as shown.
Use Box Wrench (E) to tighten all the Nuts (C) clockwise until secure.
Dx4 Fx4 Hx1 Hardware & Tool required
2
Position 1 piece of Legs (5) to the assembled Top Panel (1), Side Panels (2), and Bottom Panel (3) as shown.
Insert 2 pieces of Long Bolt (F) with 2 pieces of Flat Washer (D) into the pre-drilled holes in the Bottom Panel (3)
through the holes In the Leg (5).
Use Allen Wrench (H) to tighten Long Bolts (F) clockwise until secure.
Repeat the same steps for the other piece of Leg (5).
2
2
2
3
3
D
C
E
E
1
2
2
5
5
3
3
5
D
F
H

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 6
EEI-2678/2679 TV STAND
A
A
G
D
H
5
5
4
3
2
2
2
A
A
A
A
1
4
STEP 5:
Ax1 Dx4 Gx4 Hx1 Hardware & Tool required
STEP 6:
Position Center Panel (4) to the assembled Top Panel (1), Side Panels (2), Bottom Panel (3), and Legs (5) as shown.
Insert 4 pieces of Short Bolts (G) with 4 pieces of Flat Washer (D) into the pre-drilled holes in the Legs (5) through the
holes In the Center Panel (4).
Use Allen Wrench (H) to tighten Short Bolts (G) clockwise until secure.
Insert 6 pieces of Double-ended Bolt (A) into the corresponding holes on the Center Panel (4) by hand as shown.
Tighten all the Double-ended Bolts (A) clockwise until secure.
Position the remaining 3 pieces of assembled Side Panel (2) to the assembled Top Panel (1), Side Panels (2),
Bottom Panel (3), and Center Panel (4) as shown.
Please confirm the assembled Double-ended Bolts (A) and Dowel (B) have been inserted into the pre-drilled holes on
Center Panel (4) fully as shown.
A
A
1
5
B
2
2
2
3
4
2
2
2
B 5

EEI-2678/2679 TV STAND
STEP 7:
Cx6 Dx6 Ex1 Hardware & Tool required
STEP 8:
1
Position the other piece of Bottom Panel (3) to the assembled Top Panel (1), Side Panels (2), Bottom Panel (3),
and Center Panel (4) as shown.
Please confirm the assembled Double-ended Bolts (A) and Dowel (B) have been inserted into the pre-drilled holes on the
other piece of Bottom Panel (3) fully.
Insert 6 pieces of Nut (C) with 6 pieces of Flat Washer (D) into the assembled Double-ended Bolts (A) as shown.
Use Box Wrench (E) to tighten all the Nuts (C) clockwise until secure.
Position 1 piece of Legs (5) to the assembled Top Panel (1), Side Panels (2), and Bottom Panel (3) as shown.
Insert 2 pieces of Long Bolts (F) with 2 pieces of Flat Washer (D) into the pre-drilled holes in the Bottom Panel (3)
through the holes In the Leg (5).
Use Allen Wrench (H) to tighten Long Bolts (F) clockwise until secure.
Repeat the same steps for the other piece of Leg (5).
2
2
2
3
3
D
C
E
2
3
4
2
2
1
Tear off the sticker on the 4 pieces of Mats (J).
Carefully attach 4 pieces of Mat (J) to Legs (5) as shown.
2
2
2
3
3
D
F
E
1
2
2
2
4
5
5
5
5
J
5
5
3
3
Customer Service 908-368-1025︱www.modwayfurniture.com Page 5 of 6
Hardware & Tool required
Dx4 Fx4 Hx1 Jx4