modway 1384 User manual

Page 1 of 3
Component:
Hardware:
EEI - 1384/1491/3779 CHAIR
Thank you for purchasing the MODWAY CHAIR!
Before you start, here is some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2. Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6. Please keep all pieces out of reach of small children.
JCBC BOLT M6 x 45mm
JCBC BOLT M6 x 60mm
JCBC BOLT M6 x 90mm
FLAT WASHER M6
SPRING WASHER M6
ALLEN KEY (BALL SHAPE) M4
1 PCS
4 PCS
4 PCS
9 PCS
9 PCS
1 PC
A
B
C
D
E
F
Chair Back
1 x1 Seat Frame2 x1 Front Leg
3 x2
2
3
3
1
Customer Service 609-256-9000 www.modway.com

Hardware & Tool required
Hardware & Tool required
Please put Chair back (1) upside down on a carpeted or padded area.
Then open the black fabric which is attached by the Velcro from back to front on bottom of the Seat Frame (2), The inside of
the Seat Frame (2) will now be visible.
Attach Seat Frame (2) to Chair Back (1) by using 1 pieces of Blot (A), 1 pieces of Spring Washer (E) and 1 pieces of Flat
Waher (D) as shown.
DO not fully tighten Bolt (A) at this step also.
STEP 1:
Attach Seat Frame (2) to Chair Back (1) by 4 pieces of Bolt (C), 4 pieces of Spring Washer (E) and 4 pieces of
Flat washer (D) as shown.
Do not fully tighten Bolt (C) at this step.
STEP 2:
Page 2 of 3
Ax1 Dx1 Ex1
Cx4 Dx4 Ex4
1
2
F
A
E
D
Fx1
1
2
F
Fx1
C
E
D
Customer Service 609-256-9000 www.modway.com
EEI - 1384/1491/3779 CHAIR

Hardware & Tool required
Hardware & Tool required
Insert 1 piece of Front Leg (3) into the upper hole on the bottom of Seat Frame(2) as shown.
Attach by 2 pieces of Bolt (B), 2 pieces of Spring Washer (E) and 2 pieces of Flat Wahser (D) as shown.
Repeat the same steps for Front leg (3)
Do not fully tighten Bolts (B) for either leg.
STEP 3:
Carefullly turn over the chair.
Please put a heavy object or seat one adult on top of the Seat Frame (2) to pressure the chair for leveling.
Fully tighten all Bolts (A,B,C) with Allen Wrench (F).
STEP 4:
Assembly is completed. The chair is ready to use now!
Page 3 of 3
Bx4 Dx4 Ex4
Fx1
1
2
3
F
B
E
D
Fx1
2
F
Customer Service 609-256-9000 www.modway.com
EEI - 1384/1491/3779 CHAIR