modway EEI-2803 User manual

EEI-2803/2804 BAR TABLE
Customer Service 609-256-9000︱www.modway.com
Page 1of 4
Thank you for purchasing the MODWAY BAR TABLE.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the Bar Table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Hardware:
Components:
Double-End Bolt
x4
Flat Washer Dia22mm x8
1. Table Glass x1 2. Table Top x1 3. Table Leg x4 4. Stretcher x1
A.
H.
Allen Wrench x1
C.
Spring Washer ¼ x8
D.
Bolt M6x20mm x8
B.
Nut ¼ x4
E.
Wrench ¼ x1
F.
Flat Washer Dia18mm x8
G.
I.
Plastic Cover x4
J.
Hammer (Not Provided)

EEI-2803/2804 BAR TABLE
Customer Service 609-256-9000︱www.modway.com
Page 2of 4
STEP 1:
1. Please put Table Top (2) upside down on a carpeted or padded area.
2. Fully secure 4 pieces of Double-End Bolts (A) with 4 pieces of Flat Washers (C) and 4 pieces of
Spring Washers (D) into the bottom of Table Top (2) as shown.
3. Secure the assembled Double-End Bolts (A) towards Table Top (2) by hand as shown.
4. Insert Wrench (F) without handle into the assembled Double-End Bolts (A) and use Wrench (F) to fully
secure nuts which preassembled on Double-End Bolts (A) by inserting half of handle into Wrench (F) as
shown.
STEP 2:
Put 4 pieces of Table Legs (3) to Table Top (2) through the assembled Double-End Bolts (A) as shown.
Noted:
This side with middle of pre-drilled
holes face toward to another leg.

EEI-2803/2804 BAR TABLE
Customer Service 609-256-9000︱www.modway.com
Page 3of 4
STEP 3:
1. Place Stretcher (4) to the assembled Table Top (2) and Table Legs (3) as shown.
2. Insert 8 pieces of Bolts (B) with 8 pieces of Flat Washers (G) into the holes on Table Legs (3) through the
holes on Stretcher (4).
3. Use Allen Wrench (H) to tighten all Bolts (B) clockwise until secure.
STEP 4:
1. Secure 4 pieces of Nuts (E), 4 pieces of Spring Washers (D) and 4 pieces of Flat Washers (C) to the other
end of assembled Double-End Bolts (A) as shown.
2. Use Wrench (F) to tighten all Nuts (E) clockwise until secure.

EEI-2803/2804 BAR TABLE
Customer Service 609-256-9000︱www.modway.com
Page 4of 4
STEP 5:
Insert 4 pieces of Plastic Covers (I) into the assembled Table Legs (3) by using Hammer (J) as shown.
STEP 6:
1. Carefully turn over the assembled bar table.
2. Put Table Glass (1) to the Table Top (2) as shown.
Assembly is complete. Your Bar Table is ready to enjoy now!