modway EEI-3045 User manual

EEI-3045 Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 5
Thank you for purchasing the
MODWAY CHAIR.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 25 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
A. Bolt M8x60mm x 10
B. Flat Washer M8 x 10
C. Allen Wrench x1
Component:
1 Back Cushion x1 2 Seat Cushion x1 3 Back Frame x1 4 Left Arm x1
5 Right Arm x1 6 Seat Frame x1 7 Leg x4
5
6
3

EEI-3045 Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 5
STEP 1:
Please take t he compressed Seat Cushions (2), Back Cushions (1), all Legs and hardwares bag from the
bottom of Seat Frame (6).
Carefully remove plastic packaging of the compressed Seat Cushions (2) and Back Cushions (1).
Being carefully not to cut through to them.
Place compressed Seat Cushions (2) and Back Cushions (1) on a flat surface in a well ventilated room and
allow 48 hours for expansion.
Due to the unique properties of the compressed Seat Cushions (2) and Back Cushions (1), dimensions after
expansion will vary slightly; this is normal and will not affect the performance of your chair.
STEP 2:
Please put Sofa Frame (6) on a carpeted or padded surface.
Insert Leg (7) to the bottom of Frame (6) and tight by hand in the direction of the arrow as shown.
Repeat the same steps for the other 3 pieces of Leg (7).
HARDWARE
INSIDE
8
6
7
6
7
7
7
FRONT
BACK

EEI-3045 Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 5
STEP 3:
Attach Left Arm (4) to the side of Seat Frame (6) by using 4 pieces of Bolts (A) with 4 pieces of Flat Washers (B)
as shown.
Tighten Bolts (A) by using Allen Wrench (C) as shown. Don't tight Bolts (A) fully.
Hardware & Tools required
STEP 4:
Attach Right Arm (5) to the side of Seat Frame (6) by using 4 pieces of Bolts (A) with 4 pieces of Flat Washers
(B) as shown.
Tighten Bolts (A) by using Allen Wrench (C) as shown. Don't tight Bolts (A) fully.
Hardware & Tools required
A
x 4x 4
B
x 1
C
A
x 4x 4
B
x 1
C
4
FRONT
BACK
A
C
B
4
5
6
FRONT
BACK

EEI-3045 Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4 of 5
STEP 5:
Slide the two clips of Back Frame (3) to the clips of the side of the Left Arm (4), Right Arm (5) by hand in the
direction of the arrow as shown.
STEP 6:
Insert 2 pieces of Bolts (A) with 2 pieces of Flat Washers (B) into the pre-drilled holes on Seat Frame (6) .
Use Allen Wrench (C) to tighten Bolts (A) as shown. Don't tight Bolts (A) fully.
When Left Arm (4), Right Arm (5) and Back Frame (3) fixed, please fully tighten all Bolts (A).
Hardware & Tools required
A
x 2 x 2
B
x 1
C
4
5
6
3
4
4
5
FRONT
BACK

EEI-3045 Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 5 of 5
STEP 7:
Put Back Cushion (1) and Seat Cushion (2) to the assembled chair as shown.
Assembly is complete. Your Chair is ready to be used now!
6
2
1