modway EEI–2805 User manual

Before you start, here is some helpful advice:
Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI–2805/2806/2807/2808 TABLE
Hardware:
Component:
A Double-End Bolt x 4
Thank you for purchasing the MODWAY TABLE!
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
C Spring Washer 1/4” x 8
Table Glass x1 2 Table Top x1 3 Table Leg x4
1
1
D Flat Washer 1/4” x 8
E Wrench 1/4” x 1
F Plastic Cover x 4
B Nut 1/4” x 4
3
3
3
3
2
Hammer (Not provided)

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI–2805/2806/2807/2808 TABLE
STEP 1:
2
Cx4 Dx4 EX1 Hardware & Tool required
Please put Table Top (2) upside down on a carpeted or padded area.
Fully secure 4 pieces of Double-End Bolt (A) with 4 pieces of Spring Washer (C), 4 pieces of Flat Washer (D) into the bottom of
Table Top (2) as shown.
Secure the assembled Nuts (B) towards Table Top (2) by hand as shown.
Insert Wrench (E) without handle into the assembled Double-End Bolts (A) and use Wrench (E) to fully secure Nuts which pre-
assembled on Double-End Bolts (A) by inserting half of handle into
Wrench (E) as shown.
A
A
A
A
2
D
C
A
D
C
B
B
C
D
B
D
C
B
C
D
B
E
D
A
Handle
STEP 2:
Put 4 pieces of Table Leg (3) to Table Top (2) through the assembled Double-End Bolt (A) as shown.
2
3
3
3
3
This side with middle of pre-drilled
holes face toward to the another leg.
Note:

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI–2805/2806/2807/2808 TABLE
STEP 3:
Bx4 Ex1 Cx4 Dx4
Secure 4 pieces of Nut (B), 4 piece of Spring Washer (C), and 4 pieces of Flat Washer (D) to the other end of assembled
Double-End Bolt (A) as shown.
Use Wrench (E) to tighten Nuts (B) clockwise until secure.
2
3
3
3
3
E
B
C
D
3
D
B
C
D
C B
D
C B
D
C B
STEP 4:
Insert 4 pieces of Plastic Cover (F) into the assembled Table Leg (3) by using Hammer (Not provided) as shown.
Hardware & Tool required
3
3
2
3
3
F
F
F
F
Fx4 Not provided

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI–2805/2806/2807/2808 TABLE
STEP 5:
Carefully turn over the assembled table.
Put Table Glass (1) to the Table Top (2) as shown.
Assembly is complete. Your table is ready to be used now!
1
2
3
3
3
3