modway EEI-3147 User manual

EEI-3147 DINING TABLE
Customer Service 609-256-9000︱www.modway.com
Page 1 of 4
Thank you for purchasing the MODWAY Dining Table.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the Dining Table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6. Please keep all pieces out of reach of children.
Hardware:
Components:
Bolt M8x20mm x16
Small Flat Washer x18
1. Leg x2 2. Handle x2 3. Top Panel x1 4. Upper Rail x2 5. Bottom Support
x1
C.
Allen Wrench M8 x1
E.
Bolt M6x15mm x2
B.
A.
Big Flat Washer x4
D.
Allen Wrench M6 x1
F.
Large Nut x2
G.
Adjustable Spanner x1
H.
* Not include hardware bag

EEI-3147 DINING TABLE
Customer Service 609-256-9000︱www.modway.com
Page 2 of 4
STEP 1:
1. Please remove the plastic cover as shown with Figure 1.
2. Please insert Handle (2) into Leg (1) by the convex slot as shown with Figure 2.
3. Use Allen Wrench (F) to tighten Bolts (B) and Small Flat Washer (C) clockwise as shown with Figure 3.
4. Repeat the same way to assemble the handle on the other side
STEP 2:
1. Please insert 1 piece of Bottom Support (5) into the pre-drilled holes on one side of Leg (1) with 1 piece of Big
Flat Washer (D) as shown with Figure 2.
2. Please insert 2 pieces of Upper Rails (4) into the pre-drilled holes on one side of Leg (1) by the convex slot as
shown with Figure 1.
3. Repeat the same way to assemble the Upper Rails (4) and Bottom Support (5) on the other side of Leg (1).

EEI-3147 DINING TABLE
Customer Service 609-256-9000︱www.modway.com
Page 3 of 4
STEP 3:
1. Attach 1 piece of Big Nut (G) and 1 piece of Big Flat Washer (D) to the end of Bottom Support (5) as shown.
2. Use Adjustable Spanner (H) to tighten Big Nut (G) clockwise until secure.
3. Repeat the same way to assemble the other side.
STEP 4:
1. Please put Top Panel (3) upside down on a carpeted or padded surface.
2. Attach Leg (1) to the Top Panel (3) by using 16 pieces of Bolts (A) and 16 pieces of Small Flat Washers (C)
as shown and use Allen Wrench (E) to tighten all Bolts (B) clockwise as shown.
Note: It takes two adults to lift Legs (1) when placed on the Top Panels (3).

EEI-3147 DINING TABLE
Customer Service 609-256-9000︱www.modway.com
Page 4 of 4
STEP 5
Carefully turn over the assembled Dining Table by at two adults.
Note: Shaking the handle (2) can adjust the height of the Top panel (3).
Assembly is complete. Your Dining Table is ready to enjoy now!