modway Conduit EEI-2799 User manual

Long Bolt x40mm x 8
Short Bolt x20mm x 8
Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI–2799/2800 BAR STOOL
Hardware:
Components:
A
1
Thank you for purchasing the MODWAY BAR STOOL!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the bar stool, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
C Flat Washer x 16
4
4
3
Bar Stool Back x1 2 Bar Stool Seat x1 3 Bar Stool Front x1
1
2
B
D Allen Wrench x 1
4 Stretcher x2
5
5
EEI-1006 Seat Cushion (Packed separately)

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI–2799/2800 BAR STOOL
STEP 1:
STEP 2:
Please put Bar Stool Back (1) on a carpeted or padded area.
Place Bar Stool Seat (2) to as shown.
Insert 4 pieces of Long Bolt (B) with 4 pieces of Flat Washer (C) into the holes on Bar Stool Back (1) through the holes on
Bar Stool Seat (2) .
Use Allen Wrench (D) to tighten Long Bolts (B). Do not fully tighten Long Bolts (B) at this step.
Place Stretchers (4) to the assembled Bar Stool Back (1), and Bar Stool Seat (2) as shown.
Insert 4 pieces of Short Bolt (A) with 4 pieces of Flat Washer (C) into the holes on Bar Stool Back (1) through the holes on
Stretchers (4).
Use Allen Wrench (D) to tighten Short Bolts (A). Do not fully tighten Short Bolts (A) at this step.
Bx4 Cx4 Dx1 Hardware & Tool required
Hardware & Tool required
1
B
2
C B
C
Ax4 Cx4 Dx1
4
1
4
A
C
A
C
D
D
Bar Stool Back (1)
2

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI–2799/2800 BAR STOOL
STEP 3:
Put Bar Stool Front (3) to the assembled Bar Stool Back (1) , Bar Stool Seat (2), and Stretchers (4) as shown.
Insert 4 pieces of Long Bolt (B) with 4 pieces of Flat Washer (C) into the holes on Bar Stool Front (3) through the holes on
Bar Stool Seat (2).
Insert 4 pieces of Short Bolt (A) with 4 pieces of Flat Washer (C) into the holes on Bar Stool Back (1) through the holes on
Stretchers (4).
Use Allen Wrench (D) to tighten all the Short Bolts (A) and Long Bolts (B). Do not fully tighten the Bolts (A&B) at this step.
3
Bx4 Cx8 Dx1 Ax4 Hardware & Tool required
Carefully turn over the assembled Bar Stool.
Please put a heavy object or seat one adult on top of the assembled Bar Stool to press the bar stool
for leveling.
Use Allen Wrench (D) to tighten all the Short Bolts (A) and Long Bolts (B) clockwise until secure.
STEP 4:
Dx1 Hardware & Tool required
A
C
A
C
D
B C
B C
D
1
2
Assembly is complete. Your Bar Stool are ready to be used now!

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI–2799/2800 BAR STOOL
Carefully put Seat Cushion (5) to Bar Stool Seat (2)..
Fasten Seat Cushion (5) to Bar Stool Seat (2) by using the band on Seat Cushion (5) as shown.
STEP 5:
Band on Seat Cushion (5)
5