modway EEI-2870 User manual

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 10
Thank you for purchasing the MODWAY TABLE！
Before you start, here is some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6. Please keep all fitting out of reach of children.
Hardware:
A. Bolt M8x40mm x 12
B. Nut M8 x 4
C. Double End Bolt M8x160mm x4
D. Flat Washer ø8*18mm x 12
E. Allen Wrench M5 x1
Component:
1 Table Top x1 2 Top Rail x1 3 Left Side Panel x1 4 Right Side Panel x1
5 Middle Panel x1 6 Base x1 7 Bottom Panel x1

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 10
STEP 1:
Put Middle Panel (5) on a carpeted or padded surface.
Place Middle Panel (5) to Top Rail (2) as shown.
Insert 2 pieces of Bolts (A) with 2 pieces of Flat Washers (D)into the pre-drilled holes on Middle Panel (5)
through the pre-drilled holes on Top Rail (2).
Use Allen Wrench (E)to tighten Bolts (A) clockwise until secure.
Hardware & Tools required
STEP 2:
Place 2 pieces of two Side Panels (3)&(4) to the assembled Middle Panel (5) and Top Rail (2) as shown.
Insert 2 pieces of Bolts (A) with 2 pieces of Flat Washers (D) into the pre-drilled holes on Top Rail (2) through the
pre-drilled holes on Side Panels (3)&(4).
Use Allen Wrench (E) to tighten Bolts (A) clockwise until secure.
Hardware & Tools required

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 10
STEP 3:
Put Base (6) on a carpeted or padded surface.
Place the assembled Top Rail (2), Side Panels (3)& (4), and Middle Panel (5)
to Base (6) as shown.
Insert 4 pieces of Bolts (A) into the pre-drilled holes on Top Rail (2)
through the pre-drilled holes on Side Panels (3)&(4).
Use Allen Wrench (E)to tighten Bolts (A) clockwise until secure.
Hardware & Tools required
STEP 4:
Put Table Top (1) upside down on a carpeted or padded surface.
Insert 4 pieces of Double-End Bolts (C) into the pre-drilled holes on the bottom of Table Top (1) to clockwise until
secure.
Hardware & Tools required
with 4 pieces of Flat Washers (D)

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4 of 10
STEP 5:
Place the assembled Top Rail (2), Side Panels (3)&(4), Middle Panel (5), and Base (6) to Table Top (1) as
shown.
Insert 4 pieces of Nuts (B) to the end of assembled Double-End Bolts (C).
Use Allen Wrench (E)to tighten Nuts (B) clockwise until secure.
Hardware & Tools required

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 5 of 10
STEP 6:
Place Bottom Panel (7) to the assembled Table Top (1), Top Rail (2), Side Panels (3)&(4), Middle Panel (5),
and Base (6).
Insert 4 pieces of Bolts (A)with 4 pieces of Flat Washers (D)into the pre-drilled holes on Base (6) through the
pre-drilled holes on Bottom Panel (7).
Use Allen Wrench (E)to tighten Bolts (A) clockwise until secure.
Hardware & Tools required
STEP 7:
Carefully turn over the assembled dining table.
Assembly is complete. Your table is ready to be used now!

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 6 of 10
STEP 8:
If you want to shorten the table , please do as follows.
Open the lock on the back of the table as shown.
STEP 9:
Slide table top apart follow the arrow as shown.

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 7 of 10
STEP 10:
Lift half of Butterfly Leaf to the other half and fold the apron on butterfly leaf as shown.
STEP 11:
Fold the apron of butterfly leaf as shown.

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 8 of 10
STEP 12:
Repeat the same way to fold the other side as shown.
STEP 13:
Slide table top apart follow the arrow as shown.

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 9 of 10
STEP 14:
Close the lock on the back of the table as shown.
Your shorten table is ready to be used now!
STEP 15:
If you want to elongate the table，please do as follows.
Open the lock on the back of the table and slide table top apart follow the arrow as shown.

EEI –2870 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 10 of 10
STEP 16:
Open butterfly leaf and apron of butterfly leaf as shown.
STEP 17:
Slide table top apart follow the arrow.
Close the lock on the back of the table as shown.
Your extended table is ready to be used now!