modway EEI-3936 User manual

EEI-3936/ EEI-3937/ EEI-3938
Customer Service 609-256-9000︱www.modway.com Page 1 of 4
Thank you for purchasing the M DWAY SINGLE BASIN.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2. Tools and Materials required: a. Flat, nonabrasive work surface such as a blanket or smooth cardboard;
b. Sealant.
3. Owing to the size and weight of the basin, we recommend that it is assembled by a professional two men
crew, a single person crew is much more likely to break or chip the marble top. Double tops might require a 3
men crew, on a carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30
minutes.
4. Professional installation by two person crew is required for this fixture. Install water supply and drain piping
according to local plumbing and building codes. Insure that wall and floor are square and plumb at site of
installation.
5. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
6. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
7. Please keep all the pieces out of reach of children.
Hardware:
Components:
1. Metal Frame Side x2 2. Upper Side Bar x2 3. Bottom Side Bar x2
4. Upper Middle Bar x2 5. Top with Basin x1 6. Glass x1
Bolt M8x12mm x24
.
C.
llen Wrench x1
B.
Rubber Sucker x6

EEI-3936/ EEI-3937/ EEI-3938
Customer Service 609-256-9000︱www.modway.com Page 2 of 4
STEP 1:
1. Please put 1 piece of Metal Frame Side (1) on a carpeted or padded surface.
2. Attach 2 pieces of Upper Side Bars (2), 2 pieces of Bottom Side Bars (3) and 2 pieces of Upper Middle
Bars (4) to the Metal Frame Side (1) by using 12 pieces of Bolts (A) as shown. Don’t fully tight Bolts (A).
3. Repeat the same way to assemble the other Metal Frame Side (1) as shown.
4. Use Allen Wrench (B) to tighten all Bolts (A) clockwise as shown.
STEP 2:
Always use a two men crew, a single person crew is much more likely to break or chip the Top (5).
Sometimes might require a three men crew.

EEI-3936/ EEI-3937/ EEI-3938
Customer Service 609-256-9000︱www.modway.com Page 3 of 4
STEP 3:
1. Carefully put Top (5) on the assembled Base from the Step 1 by two adults as shown. Set Top (5) on the
Base's at the back and leave about 5mm distance from the edge for all other three sides.
2. Make sure the Top (5) fits closely and pour Sealant (Not provided) for the sealing as shown.
STEP 4:
1. Put 6 pieces of Rubber Suckers (C) on the pre installed Clips of the Metal Frame Sides (1) as shown.
2. Put 1 piece of Glass (6) on the Rubber Suckers (C) with your hand as shown.

EEI-3936/ EEI-3937/ EEI-3938
Customer Service 609-256-9000︱www.modway.com Page 4 of 4
Assembly is complete. Your single basin is ready to enjoy now!
ttention:
If the Single Basin is not
stable, you may adjust
it by alignment pin.